Sharp MX-FXX2 (serv.man2) Service Manual ▷ View online
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 38
Others
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
61
1
Internet FAX
Addition of Content-X-
CIAJWNETFAX field
(in internet FAX send)
CIAJWNETFAX field
(in internet FAX send)
Setting to determine whether or not "CONtent-X-
CIAJWNETFAX" is added to the mail field in Internet
FAX send. By adding this field, printing of the mail
text on the Internet FAX receiving side can be
inhibited (however, this function is only valid when
the Internet FAX receiving side supports this field).
"0": Do not add field
"1": Add IGNORE
CIAJWNETFAX" is added to the mail field in Internet
FAX send. By adding this field, printing of the mail
text on the Internet FAX receiving side can be
inhibited (however, this function is only valid when
the Internet FAX receiving side supports this field).
"0": Do not add field
"1": Add IGNORE
0
Do not add
2
Internet FAX
Resolution type of
internet FAX
internet FAX
This sets the type of reading resolution when
sending Internet FAX.
"0": inch type
"1": mm type
sending Internet FAX.
"0": inch type
"1": mm type
0
inch type
3
Scanner
Setting of E-Mail
sending (Return
address)
sending (Return
address)
Setting to determine whether the return address is
added or not when the mail content is modified in
returning Scan to E-Mail.
"0": Return address is not added.
"1": Return address is added.
added or not when the mail content is modified in
returning Scan to E-Mail.
"0": Return address is not added.
"1": Return address is added.
1
Return address is added.
4
Scanner
Setting of E-Mail
sending (Header)
sending (Header)
Setting to determine whether the device name, the
model name, and the installing place are added to
the header or not when the mail content is modified
in returning Scan to E-Mail.
"0": The header is not added.
"1": The header is added.
model name, and the installing place are added to
the header or not when the mail content is modified
in returning Scan to E-Mail.
"0": The header is not added.
"1": The header is added.
1
The header is added.
5
Internet FAX
Setting of internet FAX
sending (Return
address)
sending (Return
address)
Setting to determine whether the return address is
added or not when the mail content is modified in
returning internet FAX.
"0": Return address is not added.
"1": Return address is added.
added or not when the mail content is modified in
returning internet FAX.
"0": Return address is not added.
"1": Return address is added.
0
Return address is not
added.
added.
6
Internet FAX
Setting of internet FAX
sending (Header)
sending (Header)
Setting to determine whether the device name, the
model name, and the installing place are added to
the header or not when the internet FAX mail content
is modified.
"0": The header is not added.
"1": The header is added.
model name, and the installing place are added to
the header or not when the internet FAX mail content
is modified.
"0": The header is not added.
"1": The header is added.
1
The header is added.
7
Internet FAX
Selection of the
Internet FAX date and
transmission source
print language
<format>
Internet FAX date and
transmission source
print language
<format>
Setting to determine the format of the date and
transmission source attached when transmitting
Internet FAX.
"0": Date format
"1": North American format
transmission source attached when transmitting
Internet FAX.
"0": Date format
"1": North American format
0
Date format
8
Scanner
File name replacement
setting (ScanToXXX)
(Line break prohibit)
setting (ScanToXXX)
(Line break prohibit)
Setting to determine whether the codes registered in
the US-ASCll are replaced with "_" or not for the file
name in ScanToXXX and the file name used as a link
destination of a hyper link mail.
"0": Not replaced
"1": Replaced (Replaced with "_")
the US-ASCll are replaced with "_" or not for the file
name in ScanToXXX and the file name used as a link
destination of a hyper link mail.
"0": Not replaced
"1": Replaced (Replaced with "_")
0
Not replaced
62
1
Scanner
Setting of attaching
"\ (back slash)" to a
common folder name
or a file name in
ScanToSMB.
"\ (back slash)" to a
common folder name
or a file name in
ScanToSMB.
Setting to determine whether "\ (back slash)" is
attached to the head of a file name or not.
"0": Not attached (When this setting is selected, the
file name is as "common folder name\file name.")
"1": Attached (When this setting is selected, the file
name is as "common folder name\\file name.")
attached to the head of a file name or not.
"0": Not attached (When this setting is selected, the
file name is as "common folder name\file name.")
"1": Attached (When this setting is selected, the file
name is as "common folder name\\file name.")
0
Not attached
2
Scanner
Secondary storage
background process
inhibit in scanner send
(other than USB)
background process
inhibit in scanner send
(other than USB)
Setting to determine whether the secondary storage
process in ScanToXXX is performed in the
background or in the foreground with "Processing"
displayed on the operation panel.
"0": Enable (Background process)
"1": Inhibit (Foreground process)
process in ScanToXXX is performed in the
background or in the foreground with "Processing"
displayed on the operation panel.
"0": Enable (Background process)
"1": Inhibit (Foreground process)
0
Enable
3
Scanner
Secondary storage
background process
when the send data
upper limit setting is
valid
background process
when the send data
upper limit setting is
valid
Setting to determine whether the secondary storage
process in ScanToXXX (except for ScanToUSB)
when the send data upper limit setting is valid is
performed in the background or in the foreground
with "Processing" displayed on the operation panel.
"0": Disable (Foreground process)
"1": Enable (Background process)
When the soft SW62-2 "Secondary storage
background process inhibit in scanner send (other
than USB)" is set to "1: Inhibit," the process is made
in the foreground regardless of this setting.
process in ScanToXXX (except for ScanToUSB)
when the send data upper limit setting is valid is
performed in the background or in the foreground
with "Processing" displayed on the operation panel.
"0": Disable (Foreground process)
"1": Enable (Background process)
When the soft SW62-2 "Secondary storage
background process inhibit in scanner send (other
than USB)" is set to "1: Inhibit," the process is made
in the foreground regardless of this setting.
0
Disable
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 39
62
4, 5
Internet FAX
Setting of size
selection in the internet
FAX reception (AB
series)
selection in the internet
FAX reception (AB
series)
The paper sizes which can be selected in the paper
selection of the internet FAX reception are set.
Since, in the paper selection for the internet FAX
reception, only one paper size can be selected
according to the received data width and the number
of lines, a user who does not use B5 paper (does not
load B5 paper in the cassette) cannot print until B5
paper is loaded. To avoid this inconvenience, the use
can use this setting for the paper size prepared in the
cassette.
"00": Selection from B5/A4/B4/A3
"01": Selection from A4/B4/A3
"10": Selection from A4/A3
"11": Selection from A4/B4
selection of the internet FAX reception are set.
Since, in the paper selection for the internet FAX
reception, only one paper size can be selected
according to the received data width and the number
of lines, a user who does not use B5 paper (does not
load B5 paper in the cassette) cannot print until B5
paper is loaded. To avoid this inconvenience, the use
can use this setting for the paper size prepared in the
cassette.
"00": Selection from B5/A4/B4/A3
"01": Selection from A4/B4/A3
"10": Selection from A4/A3
"11": Selection from A4/B4
0
Selection from B5/A4/B4/
A3
A3
0
6
Internet FAX
Valid/Invalid setting of
Internet FAX A4, 8.5 x
11 threshold
Internet FAX A4, 8.5 x
11 threshold
When printing received Internet FAX data with A4
and 8.5 x 11 paper in the tray, this setting determines
whether to make threshold values in paper selection
valid or invalid.
"0": Valid
"1": Invalid
Setting of FAX received data is performed by means
of a separate SW.
and 8.5 x 11 paper in the tray, this setting determines
whether to make threshold values in paper selection
valid or invalid.
"0": Valid
"1": Invalid
Setting of FAX received data is performed by means
of a separate SW.
1
Invalid
7
Internet FAX
Setting of Enable/
Disable of the
threshold value of the
internet FAX Mexican
legal, foolscap
Disable of the
threshold value of the
internet FAX Mexican
legal, foolscap
Setting to change the print paper judgment.
When Mexican legal is received, if the automatic
reduction is made, it may be printed in foolscap
because of the small threshold value. When Enable,
Mexican legal can be selected easily.
"0": Enable
"1": Disable
Setting of FAX received data is performed by means
of a separate SW.
When Mexican legal is received, if the automatic
reduction is made, it may be printed in foolscap
because of the small threshold value. When Enable,
Mexican legal can be selected easily.
"0": Enable
"1": Disable
Setting of FAX received data is performed by means
of a separate SW.
1
Disable
8
Internet FAX
Setting of Enable/
Disable of the
threshold value of the
internet FAX Mexican
legal, legal
Disable of the
threshold value of the
internet FAX Mexican
legal, legal
Setting to change the print paper judgment.
When Legal is received, if the automatic reduction is
made, it may be printed in Mexican legal because of
the small threshold value. When Enable, Legal can
be selected easily.
"0": Enable
"1": Disable
Setting of FAX received data is performed by means
of a separate SW.
When Legal is received, if the automatic reduction is
made, it may be printed in Mexican legal because of
the small threshold value. When Enable, Legal can
be selected easily.
"0": Enable
"1": Disable
Setting of FAX received data is performed by means
of a separate SW.
1
Disable
63
1
Internet FAX
Setting of text printing
when receiving mails
without attached files
when receiving mails
without attached files
Setting to determine whether or not to print mail texts
when incoming mails do not have attached files.
"0": Do not print mail letters
"1": Print the main text of mails
(Communication results error)
when incoming mails do not have attached files.
"0": Do not print mail letters
"1": Print the main text of mails
(Communication results error)
0
Do not print
2
Internet FAX
Report output (when
reception is refused)
<Internet FAX only>
reception is refused)
<Internet FAX only>
Setting to determine whether or not to output the
communication results sheet when reception is
refused in Internet FAX reception. However, other
than not printing is set by means of the report output
(when receiving Internet FAX) setting.
"0": Do not output
"1": Output
FAX is set at "Report output (when reception is
refused) <FAX only>." Irrespective of "Always print"
and "Error," the results sheet is not printed.
communication results sheet when reception is
refused in Internet FAX reception. However, other
than not printing is set by means of the report output
(when receiving Internet FAX) setting.
"0": Do not output
"1": Output
FAX is set at "Report output (when reception is
refused) <FAX only>." Irrespective of "Always print"
and "Error," the results sheet is not printed.
0
Do not output
3
Scanner
Display setting at times
of NW trouble
of NW trouble
Setting to determine whether or not to display on the
operation panel when network trouble occurs while
the NIC card is loaded.
"0": Display trouble
"1": Do not display trouble (do not display "CE-00"
and "CE-01")
operation panel when network trouble occurs while
the NIC card is loaded.
"0": Display trouble
"1": Do not display trouble (do not display "CE-00"
and "CE-01")
0
Display trouble
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 40
63
4
Internet FAX
Nighttime FAX mode
setting <when Internet
FAX reception is
disabled>
setting <when Internet
FAX reception is
disabled>
Setting to determine whether or not to enter the
minimum power consumption mode when the panel
power SW is turned OFF.
"0": Enter the nighttime FAX mode
"1": Do not enter the nighttime FAX mode
This soft SW is disabled (does not work) in the OSA
model.
(SW63-6: Pseudo-nighttime mode setting <External
calculation mode> functions.)
minimum power consumption mode when the panel
power SW is turned OFF.
"0": Enter the nighttime FAX mode
"1": Do not enter the nighttime FAX mode
This soft SW is disabled (does not work) in the OSA
model.
(SW63-6: Pseudo-nighttime mode setting <External
calculation mode> functions.)
0
Enter the nighttime FAX
mode
mode
5
Internet FAX
Pseudo-nighttime
mode setting <when
Internet FAX reception
is enabled>
mode setting <when
Internet FAX reception
is enabled>
Setting to determine whether or not to enter the
minimum power consumption mode when the panel
power SW is turned OFF.
"0": Enter the pseudo-nighttime FAX mode (do not
enter the nighttime mode)
"1": Do not enter the pseudo-nighttime FAX mode
(enter the nighttime mode)
This soft SW is disabled (does not work) in the OSA
model.
(SW63-6: Pseudo-nighttime mode setting <External
calculation mode> functions.)
minimum power consumption mode when the panel
power SW is turned OFF.
"0": Enter the pseudo-nighttime FAX mode (do not
enter the nighttime mode)
"1": Do not enter the pseudo-nighttime FAX mode
(enter the nighttime mode)
This soft SW is disabled (does not work) in the OSA
model.
(SW63-6: Pseudo-nighttime mode setting <External
calculation mode> functions.)
0
Enter the pseudo-
nighttime mode
nighttime mode
6
OSA
Pseudo-nighttime
mode setting <External
calculation mode>
mode setting <External
calculation mode>
Setting to determine whether the minimum low
power consumption mode is set when the panel
power switched is turned OFF in the OSA external
calculation mode.
"0": Enter the pseudo-nighttime FAX mode (do not
enter the nighttime mode)
"1": Do not enter the pseudo-nighttime FAX mode
(enter the nighttime mode)
Enable only when the external calculation mode is
ON.
Enable only in the OSA model.
power consumption mode is set when the panel
power switched is turned OFF in the OSA external
calculation mode.
"0": Enter the pseudo-nighttime FAX mode (do not
enter the nighttime mode)
"1": Do not enter the pseudo-nighttime FAX mode
(enter the nighttime mode)
Enable only when the external calculation mode is
ON.
Enable only in the OSA model.
0
Enter the pseudo-
nighttime mode
nighttime mode
7
Function
Nighttime FAX mode
setting <60W nighttime
mode>
setting <60W nighttime
mode>
Setting to determine whether the FAX BOX power is
not shut down when the panel power switch is turned
OFF (In normal cases, it is notified in the F net, dial-
in setting.)
"0": Do not enter the pseudo-nighttime FAX mode
(60W is not notified)
"1": Enter the pseudo-nighttime FAX mode (60W is
notified)
Related soft SW:
not shut down when the panel power switch is turned
OFF (In normal cases, it is notified in the F net, dial-
in setting.)
"0": Do not enter the pseudo-nighttime FAX mode
(60W is not notified)
"1": Enter the pseudo-nighttime FAX mode (60W is
notified)
Related soft SW:
SW63-4: Nighttime FAX mode setting
<when Internet FAX reception is disabled>
SW63-5: Pseudo-nighttime mode setting
<when Internet FAX reception is enabled>
SW63-6: Pseudo-nighttime mode setting
<External calculation mode>
<when Internet FAX reception is disabled>
SW63-5: Pseudo-nighttime mode setting
<when Internet FAX reception is enabled>
SW63-6: Pseudo-nighttime mode setting
<External calculation mode>
This soft SW is enable regardless of the normal
model or the OSA model.
model or the OSA model.
0
Do not enter the pseudo-
nighttime mode
nighttime mode
8
Function
Job log memory at
times of successive
communication
times of successive
communication
Setting to determine whether successive
communications in the job log are treated as 1
communication at a time or as 1 successive
communication.
"0": Treat each communication as 1
"1": Treat as 1 successive communication
communications in the job log are treated as 1
communication at a time or as 1 successive
communication.
"0": Treat each communication as 1
"1": Treat as 1 successive communication
0
Treat each communication
as 1
as 1
• Nighttime FAX mode:
• Pseudo-nighttime mode:
<Power status>
Resident power ON
Sub power OFF
Main power OFF
Sub power OFF
Main power OFF
<Power status>
Resident power ON
Sub power ON
Main power ON
Sub power ON
Main power ON
<Power SW status>
Main power SW: ON
Panel power SW: OFF
Panel power SW: OFF
<Power SW status>
Main power SW: ON
Panel power SW: OFF or ON
Panel power SW: OFF or ON
Or
Power save mode (the power save key is pressed or in the auto power shut off state)
(Either case will provide the conditions for the pseudo-nighttime mode.)
(Either case will provide the conditions for the pseudo-nighttime mode.)
<Function>
When CI (calling) signal is detected from the FAX line,
power can be supplied to the machine and the FAX BOX.
power can be supplied to the machine and the FAX BOX.
<Function>
The power is supplied to the machine (including SCU/PCU) and the FAX BOX or the
HDD, and the panel light is turned OFF.
Under this condition, the following operations except for FAX scanning can be
performed:
• FAX/NWS send, FAX receive/internet FAX receive, printer data receive, network
HDD, and the panel light is turned OFF.
Under this condition, the following operations except for FAX scanning can be
performed:
• FAX/NWS send, FAX receive/internet FAX receive, printer data receive, network
access, etc.
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 41
System settings (Line/Other)
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
64
1
Function
Background process
when specifying the
time
when specifying the
time
Setting to determine whether the secondary storage
process in ScanToXXX (except for ScanToUSB) by
specifying the time is performed in the background or
in the foreground with "Processing" displayed on the
operation panel.
When the soft SW62-2 "Secondary storage
background process inhibit in scanner send (other
than USB)" is set to "1: Inhibit," the process is made
in the foreground regardless of this setting.
"0": Disable (Foreground process)
"1": Enable (Background process)
process in ScanToXXX (except for ScanToUSB) by
specifying the time is performed in the background or
in the foreground with "Processing" displayed on the
operation panel.
When the soft SW62-2 "Secondary storage
background process inhibit in scanner send (other
than USB)" is set to "1: Inhibit," the process is made
in the foreground regardless of this setting.
"0": Disable (Foreground process)
"1": Enable (Background process)
0
Disable
2
Function
Received data printing
hold screen display
setting
hold screen display
setting
Setting to determine whether the print hold screen is
displayed or not after entering the product key of the
document service kit.
This setting can be changed only in the simulation
mode.
"0": Enable (Displayed)
"1": Disable (Not displayed)
displayed or not after entering the product key of the
document service kit.
This setting can be changed only in the simulation
mode.
"0": Enable (Displayed)
"1": Disable (Not displayed)
0
Enable (Displayed)
3
Function
Decode error process
in printing the FAX/
Internet FAX reception
data
in printing the FAX/
Internet FAX reception
data
Setting of the process when a decode error occurs in
printing the FAX/Internet FAX reception data.
"0": Judged as E7-06 trouble.
When a decode error is detected, it is judged as E7-
06 trouble and printing is not completed. The image
data of the decode error page are not deleted.
• When the power is turned OFF/ON, the received
printing the FAX/Internet FAX reception data.
"0": Judged as E7-06 trouble.
When a decode error is detected, it is judged as E7-
06 trouble and printing is not completed. The image
data of the decode error page are not deleted.
• When the power is turned OFF/ON, the received
data can be printed again. (In case of E7-06 error,
however, manual transfer cannot be performed.)
however, manual transfer cannot be performed.)
"1": Not judged as E7-06 trouble.
The area after the line of decode error is printed as
white data. It is not processed as a trouble.
The area after the line of decode error is printed as
white data. It is not processed as a trouble.
0
Judged as E7-06 trouble.
4-8
Not used
0
0
0
0
0
0
0
0
0
65
1-8
Not used
0
0
0
1
1
1
1
0
0
0
1
1
1
1
0
66
1-8
Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
67
1-8
Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
68
1, 2
Calling
Tone/Pulse initial
setting (Dial call signal
setting)
setting (Dial call signal
setting)
This is set according to dial type.
"00": 10PPS (pulse)
"01": 20PPS
"10": TONE
"11": TONE
Other than China/Thailand: If "20pps" is set, adopt
the initial TONE.
"00": 10PPS (pulse)
"01": 20PPS
"10": TONE
"11": TONE
Other than China/Thailand: If "20pps" is set, adopt
the initial TONE.
1
TONE
FAX initial
setting/
Setting
setting/
Setting
0
Click on the first or last page to see other MX-FXX2 (serv.man2) service manuals if exist.