Sharp MX-FXX2 (serv.man2) Service Manual ▷ View online
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 22
6
1-4
Calling
Setting of DTMF send
level (low group)
High group - Low
group: level difference
level (low group)
High group - Low
group: level difference
This sets the difference between the DTMF signal high area
level and low area level in units of 0.5dB.
Setting can be made over the range of -2.0dB to 5.5dB in
0.5dB increments by binary inputting.
High group - Low group
"0 0 0 0": -2.0dB
level and low area level in units of 0.5dB.
Setting can be made over the range of -2.0dB to 5.5dB in
0.5dB increments by binary inputting.
High group - Low group
"0 0 0 0": -2.0dB
"1 0 0 0": 2.0dB
"0 0 0 1": -1.5dB
"1 0 0 1": 2.5dB
"0 0 1 0": -1.0dB
"1 0 1 0": 3.0dB
"0 0 1 1": -0.5dB
"1 0 1 1": 3.5dB
"0 1 0 0": 0.0dB
"1 1 0 0": 4.0dB
"0 1 0 1": 0.5dB
"1 1 0 1": 4.5dB
"0 1 1 0": 1.0dB
"1 1 1 0": 5.0dB
"0 1 1 1": 1.5dB
"1 1 1 1": 5.5dB
1
"1000": 2.0dB
(Other country)
"0100": 0.0dB
(New Zealand)
"1010": 3.0dB (Australia)
(Other country)
"0100": 0.0dB
(New Zealand)
"1010": 3.0dB (Australia)
Adjustment
value
value
0
0
0
5-8
Not used
0
0
0
0
0
0
0
7
1-8
Calling
Setting of DTMF
minimum pause time
minimum pause time
This sets the minimum pause time between DTMF signals
when sending DTMF signals.
Minimum pause time can be set by binary inputting N over the
range of 0 to 255 (1ms x N).
Setting can be made over the range of 50ms to 255ms in 1ms
increments by binary inputting.
When SW15-3,4 are set to other than "MODEM fixed," the set
value less than 54ms is considered as 54ms.
The initial value is reverted to if a value outside of the setting
range is set.
when sending DTMF signals.
Minimum pause time can be set by binary inputting N over the
range of 0 to 255 (1ms x N).
Setting can be made over the range of 50ms to 255ms in 1ms
increments by binary inputting.
When SW15-3,4 are set to other than "MODEM fixed," the set
value less than 54ms is considered as 54ms.
The initial value is reverted to if a value outside of the setting
range is set.
0
120ms
Adjustment
value
value
1
1
1
1
0
0
0
1
1
1
0
0
0
8
1-5
Calling
DTMF signal send time
This sets the time that DTMF signals are sent when sending
DTMF signals.
Send time can be set over the rage of 70 to 310ms in 10ms
increments by binary inputting N from 0 to 31 (110ms x N).
The initial value is reverted to if a value outside of the setting
range is set.
DTMF signals.
Send time can be set over the rage of 70 to 310ms in 10ms
increments by binary inputting N from 0 to 31 (110ms x N).
The initial value is reverted to if a value outside of the setting
range is set.
0
110ms
Adjustment
value
value
1
0
1
1
0
1
1
6, 7
Calling
Dial call waiting time
This sets the waiting time from the end of line connection to
the start of dial call at times of automatic dial calling.
"00": 3.5 seconds
"01": 4 seconds
"10": 5 seconds
"11": 6 seconds
This only functions when dial tone detection is OFF.
the start of dial call at times of automatic dial calling.
"00": 3.5 seconds
"01": 4 seconds
"10": 5 seconds
"11": 6 seconds
This only functions when dial tone detection is OFF.
0
"00": 3.5 seconds
(Other country)
"01": 4 seconds (U.K./
Finland/Norway/Denmark/
Netherlands/Italy/New
Zealand/Slovakia/South
Africa/Spain/Portuguese/
Luxemburg/Belgium/
Czech/Hungary/Greece/
Poland)
(Other country)
"01": 4 seconds (U.K./
Finland/Norway/Denmark/
Netherlands/Italy/New
Zealand/Slovakia/South
Africa/Spain/Portuguese/
Luxemburg/Belgium/
Czech/Hungary/Greece/
Poland)
Adjustment
value
value
0
8
Calling
Line current detection
at times of dial calling
at times of dial calling
Setting to determine whether or not to call dial following
detection of line current during line connection at times of
automatic dial calling.
"1": No
"0": Yes
In cases where the setting is "Yes" but no line current can be
detected, dial is not called but the busy re-call procedure is
followed.
detection of line current during line connection at times of
automatic dial calling.
"1": No
"0": Yes
In cases where the setting is "Yes" but no line current can be
detected, dial is not called but the busy re-call procedure is
followed.
1
"1": No (North America/
Taiwan/Middle East/
Other3/Rusia)
"0": Yes (Other country)
Taiwan/Middle East/
Other3/Rusia)
"0": Yes (Other country)
Setting
9
1
Calling
Manual calibration
setting when sending
setting when sending
Setting to execute the manual calibration or not when
sending.
In case of an abnormal current waveform, the auto calibration
fails and the DTFM signal is deformed. This setting provides
the countermeasure against that problem.
"0": Execute
"1": Not execute
sending.
In case of an abnormal current waveform, the auto calibration
fails and the DTFM signal is deformed. This setting provides
the countermeasure against that problem.
"0": Execute
"1": Not execute
0
Execute
Setting
2
Call
arrival
arrival
Manual calibration
setting when a signal
arrives
setting when a signal
arrives
Setting to execute the manual calibration or not when a signal
arrives.
In case of an abnormal current waveform, the auto calibration
fails and the transmission is affected. This setting provides
the countermeasure against that problem.
"0": Execute
"1": Not execute
arrives.
In case of an abnormal current waveform, the auto calibration
fails and the transmission is affected. This setting provides
the countermeasure against that problem.
"0": Execute
"1": Not execute
0
Execute
Setting
3, 4
Not used
1
1
1
5
Calling
SDT signal detection
Setting to determine whether or not to detect the SDT signal,
which is the second dial tone when transmitting to the F-net.
When the SDT signal is not detected, ordinary dialling is
conducted even after 16X dialling.
"0": Do not detect
"1": Detect
which is the second dial tone when transmitting to the F-net.
When the SDT signal is not detected, ordinary dialling is
conducted even after 16X dialling.
"0": Do not detect
"1": Detect
0
Do not detect
Setting
6
Calling
No. 2 dial tone
detection
detection
Setting of ON/OFF of No.2 dial tone detection function.
"0": OFF (No. 2 dial tone detection is not performed.)
"1": ON (No. 2 dial tone detection is performed.)
"0": OFF (No. 2 dial tone detection is not performed.)
"1": ON (No. 2 dial tone detection is performed.)
0
Detection is not performed
Setting
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 23
9
7
Calling
Dial tone detection
When the setting is "Yes," the dial is sent following
confirmation of detection of the dial tone when the line is
captured; and when the setting is "No," dial is sent without a
dial tone because no confirmation of dial tone detection is
carried out after line capture.
"0": No
"1": Yes
confirmation of detection of the dial tone when the line is
captured; and when the setting is "No," dial is sent without a
dial tone because no confirmation of dial tone detection is
carried out after line capture.
"0": No
"1": Yes
1
"1": Yes (Other country)
"0": No (Australia/New
Zealand/China/Indonesia/
Thailand/Malaysia/India/
Philippine/Hong Kong/
Taiwan/Middle East/
Other3/Rusia)
"0": No (Australia/New
Zealand/China/Indonesia/
Thailand/Malaysia/India/
Philippine/Hong Kong/
Taiwan/Middle East/
Other3/Rusia)
Setting
8
Calling
Dial tone ON detection
time (during
continuous detection)
time (during
continuous detection)
This sets the waiting time from the end of line connection to
the start of dial call at times of automatic dial calling.
"0": 1.5 seconds
"1": 1 seconds
the start of dial call at times of automatic dial calling.
"0": 1.5 seconds
"1": 1 seconds
0
1.5 seconds
Adjustment
value
value
10
1-4
Calling
Lower limit of dial tone
ON/OFF detection time
(during intermittent
detection)
ON/OFF detection time
(during intermittent
detection)
This sets the lower limit time for detection of dial tone ON/
OFF time.
Setting can be made over the range of 40ms to 490ms in
30ms increments by binary inputting.
(N x 30ms) + 40ms
This is only valid during intermittent DT detection.
OFF time.
Setting can be made over the range of 40ms to 490ms in
30ms increments by binary inputting.
(N x 30ms) + 40ms
This is only valid during intermittent DT detection.
0
"0010": 100ms (North
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/Brazil)
"0001": 70ms
(Other country)
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/Brazil)
"0001": 70ms
(Other country)
Adjustment
value
value
0
1
0
5-8
Calling
Upper limit of dial tone
ON/OFF detection time
(during intermittent
detection)
ON/OFF detection time
(during intermittent
detection)
This sets the upper limit time for detection of dial tone ON/
OFF time.
Setting can be made over the range of 400ms to 1900ms in
100ms increments by binary inputting.
(N x 100ms) + 400ms
This is only valid during intermittent DT detection.
OFF time.
Setting can be made over the range of 400ms to 1900ms in
100ms increments by binary inputting.
(N x 100ms) + 400ms
This is only valid during intermittent DT detection.
0
"0011": 700ms (North
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/Brazil)
"1000": 1200ms
(Other country)
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/Brazil)
"1000": 1200ms
(Other country)
Adjustment
value
value
0
1
1
11
1-4
Calling
External line
connection number
setting 1 <First digit>
connection number
setting 1 <First digit>
When No. 2 dial tone is detected, this area is compared with
the external in connection number. If they match, the units
waits for No. 2 dial tone.
Up to two external line connection numbers (max. 4 digits)
can be registered as options.
The first digit of the external line connection number 1 is set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
the external in connection number. If they match, the units
waits for No. 2 dial tone.
Up to two external line connection numbers (max. 4 digits)
can be registered as options.
The first digit of the external line connection number 1 is set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
5-8
Calling
External line
connection number
setting 1 <Second
digit>
connection number
setting 1 <Second
digit>
The second digit of the external line connection number 1 is
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
12
1-4
Calling
External line
connection number
setting 1 <Third digit>
connection number
setting 1 <Third digit>
The third digit of the external line connection number 1 is set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
0
5-8
Calling
External line
connection number
setting 1 <Fourth digit>
connection number
setting 1 <Fourth digit>
The fourth digit of the external line connection number 1 is
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
0
13
1-4
Calling
External line
connection number
setting 2 <First digit>
connection number
setting 2 <First digit>
The first digit of the external line connection number 2 is set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
0
5-8
Calling
External line
connection number
setting 2 <Second
digit>
connection number
setting 2 <Second
digit>
The second digit of the external line connection number 2 is
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 24
14
1-4
Calling
External line
connection number
setting 2 <Third digit>
connection number
setting 2 <Third digit>
The third digit of the external line connection number 2 is set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
0
5-8
Calling
External line
connection number
setting 2 <Fourth digit>
connection number
setting 2 <Fourth digit>
The fourth digit of the external line connection number 2 is
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
set.
The numbers and codes which can be registered are as
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) /
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].
0
0
Setting
0
0
0
0
15
1, 2
Calling
DT/BT detection level
This sets the minimum detection level for determining that
dial tone and busy tone have been detected. Signal levels not
larger than this setting are ignored.
"00": -43dB
"01": -35dB
"10": -33dB
"11": -30dB
DT, BT common
dial tone and busy tone have been detected. Signal levels not
larger than this setting are ignored.
"00": -43dB
"01": -35dB
"10": -33dB
"11": -30dB
DT, BT common
0
-43dB
Adjustment
value
value
0
3, 4
Calling
DT/BT detection
frequency range
setting
frequency range
setting
This sets the detection frequency range when detecting dial
tone and busy tone.
Change the setting if dial tone and busy tone are erroneously
detected.
"00": MODEM fixed (about 308Hz - 517Hz)
"01": 420Hz - 680Hz
"10": 360Hz - 440Hz
"11": 245Hz - 650Hz
For CTR21: 245Hz - 650Hz
tone and busy tone.
Change the setting if dial tone and busy tone are erroneously
detected.
"00": MODEM fixed (about 308Hz - 517Hz)
"01": 420Hz - 680Hz
"10": 360Hz - 440Hz
"11": 245Hz - 650Hz
For CTR21: 245Hz - 650Hz
1
"11": 245Hz - 650Hz
(Other country)
"00": MODEM fixed
(Thailand/India)
"01": 420Hz - 680Hz
(China)
"10": 360Hz - 440Hz
(Indonesia/Malaysia/
Middle East/Other3/Rusia)
(Other country)
"00": MODEM fixed
(Thailand/India)
"01": 420Hz - 680Hz
(China)
"10": 360Hz - 440Hz
(Indonesia/Malaysia/
Middle East/Other3/Rusia)
Adjustment
value
value
1
5
Calling
Busy tone detection
Setting to determine whether or not to detect the busy tone
signal during automatic dial calling and when the external
telephone simulated call sound is ringing.
"0": Detect
"1": Do not detect
signal during automatic dial calling and when the external
telephone simulated call sound is ringing.
"0": Detect
"1": Do not detect
0
Detect
Setting
6
Calling
Busy tone OFF non-
detection time
detection time
This sets the non-detection time on the busy tone OFF
section.
Change the setting in cases where noise, etc. on the busy
tone ON section adversely affects the ON section.
"0": 100ms
"1": 300ms
* Make shorter than the "busy tone OFF detection time."
section.
Change the setting in cases where noise, etc. on the busy
tone ON section adversely affects the ON section.
"0": 100ms
"1": 300ms
* Make shorter than the "busy tone OFF detection time."
0
100ms
Adjustment
value
value
7, 8
Calling
Lower limit of busy
tone ON detection time
tone ON detection time
This sets the lower limit time of the ON section when
detecting frequency of the busy tone signal.
If busy tone signals are not detected in excess of this time, do
not count as 1 pulse.
"00": 250ms
"01": 140ms
"10": 450ms
"11": 350ms
detecting frequency of the busy tone signal.
If busy tone signals are not detected in excess of this time, do
not count as 1 pulse.
"00": 250ms
"01": 140ms
"10": 450ms
"11": 350ms
0
"00": 250ms (North
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/South Africa)
"01": 140ms
(Other country)
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/South Africa)
"01": 140ms
(Other country)
Adjustment
value
value
0
16
1, 2
Calling
Upper limit of busy
tone ON detection time
tone ON detection time
This sets the upper limit time of the ON section when
detecting frequency of the busy tone signal.
If busy tone signal is detected in excess of this time, do not
count as 1 pulse.
"00": 750ms
"01": 650ms
"10": 1000ms
"11": 2850ms
detecting frequency of the busy tone signal.
If busy tone signal is detected in excess of this time, do not
count as 1 pulse.
"00": 750ms
"01": 650ms
"10": 1000ms
"11": 2850ms
0
"00": 750ms
(Other country)
"10": 1000ms
(Australia/India)
"11": 2850ms
(Singapore/South Africa)
(Other country)
"10": 1000ms
(Australia/India)
"11": 2850ms
(Singapore/South Africa)
Adjustment
value
value
0
3, 4
Calling
Lower limit of busy
tone OFF detection
time
tone OFF detection
time
This sets the lower limit time of the OFF section when
detecting frequency of the busy tone signal.
If busy tone OFF signals are not detected in excess of this
time, do not count as 1 pulse.
"00": 250ms
"01": 140ms
"10": 450ms
"11": 350ms
detecting frequency of the busy tone signal.
If busy tone OFF signals are not detected in excess of this
time, do not count as 1 pulse.
"00": 250ms
"01": 140ms
"10": 450ms
"11": 350ms
0
"00": 250ms (North
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/South Africa)
"01": 140ms
(Other country)
America/Australia/New
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/South Africa)
"01": 140ms
(Other country)
Adjustment
value
value
0
5, 6
Calling
Upper limit of busy
tone OFF detection
time
tone OFF detection
time
This sets the upper limit time of the OFF section when
detecting frequency of the busy tone signal.
If busy tone signal is detected in excess of this time, do not
count as 1 pulse.
"00": 750ms
"01": 650ms
"10": 1000ms
"11": 2850ms
detecting frequency of the busy tone signal.
If busy tone signal is detected in excess of this time, do not
count as 1 pulse.
"00": 750ms
"01": 650ms
"10": 1000ms
"11": 2850ms
0
"00": 750ms
(Other country)
"10": 1000ms (Singapore/
India/South Africa)
(Other country)
"10": 1000ms (Singapore/
India/South Africa)
Adjustment
value
value
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 25
16
7, 8
Not used
0
0
0
17
1-4
Call
arrival
arrival
Call signal OFF non-
detection time
detection time
This sets the time for ignoring OFF signals and regarding ON
time to be continuous following ON detection of the call signal
(CI).
This is intended to treat the PBX call signal "ring-ring" as a
single call signal.
Setting can be made over the range of 0ms to 1500ms in
100ms increments by binary inputting.
time to be continuous following ON detection of the call signal
(CI).
This is intended to treat the PBX call signal "ring-ring" as a
single call signal.
Setting can be made over the range of 0ms to 1500ms in
100ms increments by binary inputting.
0
"0110": 600ms (North
America/Australia/Taiwan/
Middle East/Other3/Rusia)
"0100": 400ms
(Other country)
"1010": 1000ms
(New Zealand)
America/Australia/Taiwan/
Middle East/Other3/Rusia)
"0100": 400ms
(Other country)
"1010": 1000ms
(New Zealand)
Adjustment
value
value
1
1
1
0
5-8
Call
arrival
arrival
Lower limit of call
signal ON time
signal ON time
This sets the minimum ON time for detecting call signal (CI)
pulses (number of pulses). 1 pulse is counted if the CI signal
remains ON for the set ON time or longer.
Setting can be made over the range of 150ms to 300ms in
10ms increments by binary inputting.
pulses (number of pulses). 1 pulse is counted if the CI signal
remains ON for the set ON time or longer.
Setting can be made over the range of 150ms to 300ms in
10ms increments by binary inputting.
0
"0000": 150ms
(Other country)
"0010": 170ms (Australia)
(Other country)
"0010": 170ms (Australia)
Adjustment
value
value
0
0
0
0
0
18
1-4
Call
arrival
arrival
Upper limit of call
signal ON time
signal ON time
This sets the maximum ON time for detecting call signal (CI)
pulses (number of pulses). Disregard and do not count as 1
pulse if the CI signal remains ON for the set ON time or
longer.
Setting can be made over the range of 3000ms to 4500ms in
100ms increments by binary inputting.
pulses (number of pulses). Disregard and do not count as 1
pulse if the CI signal remains ON for the set ON time or
longer.
Setting can be made over the range of 3000ms to 4500ms in
100ms increments by binary inputting.
0
3000ms
Adjustment
value
value
0
0
0
0
0
5-8
Call
arrival
arrival
Lower limit of call
signal OFF time
signal OFF time
This sets the minimum OFF time for detecting call signal (CI)
pulses (number of pulses). 1 pulse is counted if the CI signal
remains OFF for the set OFF time or longer.
Setting can be made over the range of 100ms to 1500ms in
100ms increments by binary inputting.
Setting range
When 0 is set, initial value 700ms operation takes place.
pulses (number of pulses). 1 pulse is counted if the CI signal
remains OFF for the set OFF time or longer.
Setting can be made over the range of 100ms to 1500ms in
100ms increments by binary inputting.
Setting range
When 0 is set, initial value 700ms operation takes place.
0
700ms
Adjustment
value
value
1
1
1
1
19
1, 2
Call
arrival
arrival
Upper limit of call
signal OFF time
signal OFF time
This sets the maximum waiting time from detection of the call
signal (CI) pulse (number of pulses) to detection of the next
CI signal pulse.
Accordingly, if the next CI signal pulse is not detected within
this time, the number of calls up to now is cleared.
"00": 6.5 seconds
"01": 10 seconds
"10": 15 seconds
"11": 20 seconds
signal (CI) pulse (number of pulses) to detection of the next
CI signal pulse.
Accordingly, if the next CI signal pulse is not detected within
this time, the number of calls up to now is cleared.
"00": 6.5 seconds
"01": 10 seconds
"10": 15 seconds
"11": 20 seconds
0
"00": 6.5 seconds
(Other country)
"01": 10 seconds
(Sweden/Indonesia)
(Other country)
"01": 10 seconds
(Sweden/Indonesia)
Adjustment
value
value
0
3
Call
arrival
arrival
CI clear judgment
Setting of the judgment of CI signal 1 cycle.
"1": Cleared only when the max. cycle is exceeded. (The min.
cycle is 0.)
"0": Cleared when outside the range of 1 cycle. (The min. and
the max. cycles are set with other soft switches.)
"1": Cleared only when the max. cycle is exceeded. (The min.
cycle is 0.)
"0": Cleared when outside the range of 1 cycle. (The min. and
the max. cycles are set with other soft switches.)
0
Cleared when outside the
range of 1 cycle.
range of 1 cycle.
4, 5
Call
arrival
arrival
Filter time when the CI
signal is detected.
signal is detected.
The detection sampling time of the CI signal is set in the CI
signal detection setting.
"00": 10ms
"01": 5ms
"10": 15ms
"11": 20ms
signal detection setting.
"00": 10ms
"01": 5ms
"10": 15ms
"11": 20ms
0
10ms
0
6-8
Not used
0
0
0
0
0
20
1-8
Not used
0
0
0
0
0
1
0
1
0
0
0
0
1
0
1
21
1-8
Not used
1
0
1
0
0
0
0
0
0
1
0
0
0
0
0
22
1-8
Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
Click on the first or last page to see other MX-FXX2 (serv.man2) service manuals if exist.