Sharp MX-FXX2 (serv.man2) Service Manual ▷ View online
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 26
Communications
23
1-8
Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
24
1-8
Communication
Signal sending level
Set the level adjustment for sending signals from
the modem. Setting can be made over the range
of 0 to 26 in 1dBm increments by binary inputting.
Since the maximum level differs according to
country, if a value above the maximum level is
set, the maximum value for the present country
code will be adopted. (For North America and
China, there is no limitation on the max. send
level.)
When set to a value greater than the upper limit, it
is considered as setting to the upper limit. When
set to a value smaller than the lower limit, it is
considered as setting to the lower limit.
If, however, it is set to 27 to 255, it is considered
as setting to 26.
the modem. Setting can be made over the range
of 0 to 26 in 1dBm increments by binary inputting.
Since the maximum level differs according to
country, if a value above the maximum level is
set, the maximum value for the present country
code will be adopted. (For North America and
China, there is no limitation on the max. send
level.)
When set to a value greater than the upper limit, it
is considered as setting to the upper limit. When
set to a value smaller than the lower limit, it is
considered as setting to the lower limit.
If, however, it is set to 27 to 255, it is considered
as setting to 26.
0
"00001011": -11dBm
(North America/Australia/
New Zealand/India/
Taiwan/Rusia)
"00001000": -8dBm
(Other3)
"00001001": -9dBm
(Other country)
"00001010": -10dBm
(China/Singapore/
Thailand/Malaysia/
Philippine/Hong Kong/
Middle East/Brazil)
(North America/Australia/
New Zealand/India/
Taiwan/Rusia)
"00001000": -8dBm
(Other3)
"00001001": -9dBm
(Other country)
"00001010": -10dBm
(China/Singapore/
Thailand/Malaysia/
Philippine/Hong Kong/
Middle East/Brazil)
Adjustment
value
value
0
0
0
1
0
1
1
25
1-3
Transmission
Setting of call time (T0
timer setting) in
automatic transmission
timer setting) in
automatic transmission
Setting to determine how many seconds to call
when the other party doesn’t respond at times of
automatic transmission.
Setting can be made over the range of 30 to 60
(China: 30 to 45, Rusia: 30 to 35) seconds in 15
(Rusia: 5) second increments by binary inputting
N ((15 (Rusia: 5) seconds x N) + 30 seconds).
The initial value is reverted to if a value outside of
the setting range is set.
when the other party doesn’t respond at times of
automatic transmission.
Setting can be made over the range of 30 to 60
(China: 30 to 45, Rusia: 30 to 35) seconds in 15
(Rusia: 5) second increments by binary inputting
N ((15 (Rusia: 5) seconds x N) + 30 seconds).
The initial value is reverted to if a value outside of
the setting range is set.
0
45 seconds
(Other country)
35 seconds (Rusia)
(Other country)
35 seconds (Rusia)
Timer
0
1
4-7
Communication
T1 timer setting
Setting to determine how many seconds the line
is connected when the other party’s machine
doesn’t respond to FAX communication.
Setting can be made over the range of 30 to 105
seconds in 5-second increments by binary
inputting ((5 seconds x N) + 30 seconds).
T1 timer is the timer used from the point where
the other party’s machine recognizes (CED or
DCS) as FAX following line connection. 35±5
seconds according to the ITU-T standard.
is connected when the other party’s machine
doesn’t respond to FAX communication.
Setting can be made over the range of 30 to 105
seconds in 5-second increments by binary
inputting ((5 seconds x N) + 30 seconds).
T1 timer is the timer used from the point where
the other party’s machine recognizes (CED or
DCS) as FAX following line connection. 35±5
seconds according to the ITU-T standard.
0
40 seconds
Timer
0
1
0
8
Not used
0
26
1, 2
Communication
T2 timer setting
The time until a command is received is set.
"00": 6 seconds
"01": 7 seconds
"10": 8 seconds
"11": 9 seconds
This is the timer for receiving a command such as
the DIS signal. 6
"00": 6 seconds
"01": 7 seconds
"10": 8 seconds
"11": 9 seconds
This is the timer for receiving a command such as
the DIS signal. 6
±1 seconds in the ITU-T
standards.
0
6 seconds
0
3, 4
Communication
T4 timer setting
Timer during automatic
operation (+1.5
seconds at times of
manual operation)
Timer during automatic
operation (+1.5
seconds at times of
manual operation)
This sets the timer for up until reception of the
response.
+1.5 seconds at times of manual operation
"00": 3 seconds
"01": 4 seconds
"10": 5 seconds
"11": 6 seconds
This is the timer for up until reception of the
response to the DCS signal, etc. 3 seconds ±15%
under the ITU-T standard.
response.
+1.5 seconds at times of manual operation
"00": 3 seconds
"01": 4 seconds
"10": 5 seconds
"11": 6 seconds
This is the timer for up until reception of the
response to the DCS signal, etc. 3 seconds ±15%
under the ITU-T standard.
0
3 seconds
Timer
0
5
Reception
EOL detection timer
Setting to determine how many seconds to set the
detection timer for EOL (EndOfLine) during
Phase-C reception in G3.
"0": Setting to 13 seconds
"1": Setting to 25 seconds
When error occurs in EOL detection, treat as non-
detection of EOL.
detection timer for EOL (EndOfLine) during
Phase-C reception in G3.
"0": Setting to 13 seconds
"1": Setting to 25 seconds
When error occurs in EOL detection, treat as non-
detection of EOL.
0
13 seconds
Timer
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 27
26
6
Communication
Sharp machine mode
Setting is made whether Sharp's unique
procedures (relay, confidential) are allowed or not
by not sending NSF/NSS/NSC and not confirming
that the machine is a Sharp machine or not.
"0": Check
"1": Not check
procedures (relay, confidential) are allowed or not
by not sending NSF/NSS/NSC and not confirming
that the machine is a Sharp machine or not.
"0": Check
"1": Not check
0
Check
7, 8
Communication
Modem lightning
protection measures
protection measures
Function that corresponds to IEC lightning surge
requirements as prescribed in the European CE
standard.
In cases where the machine cannot shift from
CFR or MCF to high-speed signals (image
signals) due to lightning interference, this extends
the MPS waiting time.
"00": 0 second
"01": 20 seconds
"10": 30 seconds
"11": 40 seconds
requirements as prescribed in the European CE
standard.
In cases where the machine cannot shift from
CFR or MCF to high-speed signals (image
signals) due to lightning interference, this extends
the MPS waiting time.
"00": 0 second
"01": 20 seconds
"10": 30 seconds
"11": 40 seconds
0
"00": 0 second (North
America/New Zealand/
China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/Rusia/Brazil)
"01": 20 seconds
(Other country)
America/New Zealand/
China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3/Rusia/Brazil)
"01": 20 seconds
(Other country)
Setting
0
27
1, 2
Reception
CED signal sending
time
time
This sets the time over which the CED signal is
sent.
"00": 3 seconds
"01": 4 seconds
"10": 5 seconds
"11": No
sent.
"00": 3 seconds
"01": 4 seconds
"10": 5 seconds
"11": No
0
3 seconds
Communication/
Adjustment
value
Adjustment
value
0
3
Reception
CED/ANSam detection
time
time
This sets the time up until determination of the
signal when detecting CED/ANSam signals.
"0": 500ms
"1": 1000ms
signal when detecting CED/ANSam signals.
"0": 500ms
"1": 1000ms
1
1000ms
Adjustment
value
value
4
Reception
V.34 mode function (on
call arrival)
call arrival)
Setting to determine whether or not to make the
V.34 mode valid as machine capacity when
receiving (on call arrival).
"0": V.34 valid
"1": V.34 invalid
V.34 mode valid as machine capacity when
receiving (on call arrival).
"0": V.34 valid
"1": V.34 invalid
0
V.34 valid
Setting
5
Transmission
V.34 mode function
(including polling when
calling)
(including polling when
calling)
Setting to determine whether or not to make the
V.34 mode valid as machine capacity when
transmitting (calling and polling).
"0": V.34 valid
"1": V.34 invalid
V.34 mode valid as machine capacity when
transmitting (calling and polling).
"0": V.34 valid
"1": V.34 invalid
0
V.34 valid
Setting
6
Transmission
V.34 mode function at
times of manual
communication
times of manual
communication
Setting to determine whether or not to make the
V.34 mode valid at times of manual
communication (transmitting and receiving).
"0": V.34 valid
"1": V.34 invalid
However, in cases where the V.34 mode function
(including polling when calling) is set at 1: V.34
invalid, the V.34 mode will be rendered invalid
even if this SW is set to 0: valid.
V.34 mode valid at times of manual
communication (transmitting and receiving).
"0": V.34 valid
"1": V.34 invalid
However, in cases where the V.34 mode function
(including polling when calling) is set at 1: V.34
invalid, the V.34 mode will be rendered invalid
even if this SW is set to 0: valid.
0
V.34 valid
Communication/
Setting
Setting
7
Transmission
3429 symbol rate
transmission enable
during V.34
transmission.
transmission enable
during V.34
transmission.
Setting to determine whether or not to enable
3429Hz as the symbol rate for V.34.
When this is at "disable," 3429Hz is not selected.
However, only valid during transmission.
"0": disable
"1": enable
3429Hz as the symbol rate for V.34.
When this is at "disable," 3429Hz is not selected.
However, only valid during transmission.
"0": disable
"1": enable
1
enable
Setting
8
Transmission
Symbol rate 3200 high
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3200Hz is selected as the V.34 symbol
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3200 High is not
selected.
However, only valid during transmission.
When both Low/High are at "disable,"
SymbolRate=3200Hz is not selected.
"0": disable
"1": enable
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3200 High is not
selected.
However, only valid during transmission.
When both Low/High are at "disable,"
SymbolRate=3200Hz is not selected.
"0": disable
"1": enable
1
enable
Setting
28
1
Transmission
Symbol rate 3200 low
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3200Hz is selected as the V.34 symbol
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3200 Low is not
selected.
However, only valid during transmission.
"0": disable
"1": enable
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3200 Low is not
selected.
However, only valid during transmission.
"0": disable
"1": enable
1
enable
Setting
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 28
28
2
Transmission
Symbol rate 3000 high
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3000Hz is selected as the V.34 symbol
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3000 High is not
selected.
However, only valid during transmission.
When both Low/High are at "disable,"
SymbolRate=3000Hz is not selected.
"0": disable
"1": enable
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3000 High is not
selected.
However, only valid during transmission.
When both Low/High are at "disable,"
SymbolRate=3000Hz is not selected.
"0": disable
"1": enable
1
enable
Setting
3
Transmission
Symbol rate 3000 low
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3000Hz is selected as the V.34 symbol
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3000 Low is not
selected.
However, only valid during transmission.
"0": disable
"1": enable
rate, there are Low/High carriers, but this setting
determines whether or not both can be used.
When this is at "disable," 3000 Low is not
selected.
However, only valid during transmission.
"0": disable
"1": enable
1
enable
Setting
4
Transmission
Symbol rate 3429
enable during V.34
transmission
enable during V.34
transmission
Setting whether use of 3429Hz is enabled or not
as the symbol rate in V.34 transmission.
When this is set to [Disable], 3429Hz cannot be
selected.
"0": disable
"1": enable
as the symbol rate in V.34 transmission.
When this is set to [Disable], 3429Hz cannot be
selected.
"0": disable
"1": enable
1
enable
5
Transmission
Symbol rate 2800
enable during V.34
transmission
enable during V.34
transmission
Setting to determine whether or not to enable
2800Hz as the symbol rate for V.34.
When this is at "disable," 2800Hz is not selected.
"0": disable
"1": enable
2800Hz as the symbol rate for V.34.
When this is at "disable," 2800Hz is not selected.
"0": disable
"1": enable
1
enable
Setting
6
Transmission
Symbol rate 2743
enable during V.34
transmission
enable during V.34
transmission
Setting to determine whether or not to enable
2743Hz as the symbol rate for V.34.
When this is at "disable," 2743Hz is not selected.
"0": disable
"1": enable
2743Hz as the symbol rate for V.34.
When this is at "disable," 2743Hz is not selected.
"0": disable
"1": enable
1
enable
Setting
7, 8
Communication
Coding capacity during
transmission and
reception (V.34
communication)
(reflected in DIS/DCS/
DTC)
transmission and
reception (V.34
communication)
(reflected in DIS/DCS/
DTC)
This sets the coding capacity that is
communicated to the other party’s machine in
V.34 communication.
"00": JBIG/MMR/MR/MH
"01": MMR/MR/MH
"10": MR/MH
"11": MH
communicated to the other party’s machine in
V.34 communication.
"00": JBIG/MMR/MR/MH
"01": MMR/MR/MH
"10": MR/MH
"11": MH
0
JBIG/MMR/MR/MH
Communication/
Setting
Setting
0
29
1, 2
Communication
Coding capacity during
transmission and
reception (other than
V.34 communication)
(reflected in DIS/DCS/
DTC)
transmission and
reception (other than
V.34 communication)
(reflected in DIS/DCS/
DTC)
This sets the coding capacity that is
communicated to the other party’s machine in
communication other than V.34.
"00": JBIG/MMR/MR/MH
"01": MMR/MR/MH
"10": MR/MH
"11": MH
communicated to the other party’s machine in
communication other than V.34.
"00": JBIG/MMR/MR/MH
"01": MMR/MR/MH
"10": MR/MH
"11": MH
0
JBIG/MMR/MR/MH
Communication/
Setting
Setting
0
3-6
Transmission
Modem transmission
speed (Other than
V.34) (DCS)
speed (Other than
V.34) (DCS)
This sets the initial speed (upper limit) in
transmission of other than V.34. Reflect in DCS.
When the default setting is made, V.17 14400bps
is notified to the other party’s machine.
Communication does not always happen at this
speed.
transmission of other than V.34. Reflect in DCS.
When the default setting is made, V.17 14400bps
is notified to the other party’s machine.
Communication does not always happen at this
speed.
1
V.17 14400bps
Speed/
Adjustment
value
Adjustment
value
0
0
0
7, 8
Reception
Fixing of modem
speed during reception
(Other than V.34) (DIS)
speed during reception
(Other than V.34) (DIS)
This sets the initial speed (upper limit) in
transmission of other than V.34.
When the default setting is made, V.17 14400bps
is notified to the other party’s machine.
Communication does not always happen at this
speed.
"00": Not fixed
"01": V.29-9600bps
"10": V.27ter-4800bps
"11": V.17-14400bps
transmission of other than V.34.
When the default setting is made, V.17 14400bps
is notified to the other party’s machine.
Communication does not always happen at this
speed.
"00": Not fixed
"01": V.29-9600bps
"10": V.27ter-4800bps
"11": V.17-14400bps
0
Not fixed
Speed/Setting
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
"0000": V.27ter 2400bps
"1000": V.17 14400bps
"0001": V.29
9600bps
"1001": V.17 9600bps
"0010": V.27ter 4800bps
"1010": V.17 12000bps
"0011": V.29
7200bps
"1011": V.17 7200bps
"0100": V.33
14400bps
"1100": V.17 14400bps
"0101": V.17
14400bps
"1101": V.17 14400bps
"0110": V.33
12000bps
"1110": V.17 14400bps
"0111": V.17
14400bps
"1111": V.17 14400bps
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 29
30
1-4
Reception
V.34 Symbol Rate
Mask (when receiving)
Mask (when receiving)
This sets the symbol rate when receiving in the
V.34 mode.
"0000": 2400
"0001": 2400
"0010": 2800/2400
"0011": 3000/2800/2400
"0100": 3200/3000/2800/2400
"0101": 3429/3200/3000/2800/2400
When set at a value other than those shown
above, the initial value of "0101" is activated.
V.34 mode.
"0000": 2400
"0001": 2400
"0010": 2800/2400
"0011": 3000/2800/2400
"0100": 3200/3000/2800/2400
"0101": 3429/3200/3000/2800/2400
When set at a value other than those shown
above, the initial value of "0101" is activated.
0
3429/3200/3000/2800/
2400
2400
Communication/
Setting
Setting
1
0
1
5
Transmission
Echo countermeasure
(setting of hold time
between DIS reception
and sending of signal)
when transmitting.
(setting of hold time
between DIS reception
and sending of signal)
when transmitting.
Setting to determine how many seconds the
interval is from receiving DIS to sending the DCS
signal. This is only valid for communications of
other than V.34.
"0": 500msec
"1": 800msec
interval is from receiving DIS to sending the DCS
signal. This is only valid for communications of
other than V.34.
"0": 500msec
"1": 800msec
0
500msec
Communication/
Setting
Setting
6
Reception
Echo countermeasure
(CED tone sending
interval) when
receiving
(CED tone sending
interval) when
receiving
Setting to determine how many seconds the
interval is from sending CED or ANSam to
sending the DIS FSK signal.
"0": 75msec
"1": 500msec
interval is from sending CED or ANSam to
sending the DIS FSK signal.
"0": 75msec
"1": 500msec
1
500msec
Communication/
Setting
Setting
7
Transmission
Confirmation of DIS
reception when
sending
reception when
sending
Setting to determine how to confirm DIS reception
when transmitting.
"0": Once for NFS reception, twice for DIS
reception
"1": Twice
Valid apart from V.34
when transmitting.
"0": Once for NFS reception, twice for DIS
reception
"1": Twice
Valid apart from V.34
0
Once for NFS reception,
twice for DIS reception.
twice for DIS reception.
Communication/
Setting
Setting
8
Reception
Enable/Disable of 33
bit or later of DIS
(Reflected only to DIS)
bit or later of DIS
(Reflected only to DIS)
Setting whether DIS is limited to 32 bit or not
when receiving FAX.
When limited, JBIG reception, F code reception,
and UFN reception cannot be made. However,
sending is enabled as well as polling.
"0": Enable (33 bit or later enabled)
"1": Disable (33 bit or later disabled)
when receiving FAX.
When limited, JBIG reception, F code reception,
and UFN reception cannot be made. However,
sending is enabled as well as polling.
"0": Enable (33 bit or later enabled)
"1": Disable (33 bit or later disabled)
0
Enable (33 bit or later
enabled)
enabled)
31
1
Reception
CSI sending
Setting to determine whether or not to send the
CSI signal.
The CSI signal contains the transmission source
number.
"0": Yes (send the CSI signal)
"1": No (do not send the CSI signal)
CSI signal.
The CSI signal contains the transmission source
number.
"0": Yes (send the CSI signal)
"1": No (do not send the CSI signal)
0
Yes
Setting
2
Transmission
Echo suppressor tone
setting No. 1
setting No. 1
Setting to determine whether or not to have the
echo suppressor tone in the high-speed
modulation mode.
"0": With V33
"1": Without V33
echo suppressor tone in the high-speed
modulation mode.
"0": With V33
"1": Without V33
0
With V.33
Setting
3
Transmission
Echo suppressor tone
setting No. 2
setting No. 2
Setting to determine whether or not to have the
echo suppressor tone in the high-speed
modulation mode.
"0": With V17
"1": Without V17
echo suppressor tone in the high-speed
modulation mode.
"0": With V17
"1": Without V17
0
With V.17
Communication/
Setting
Setting
4
Transmission
Echo suppressor tone
setting No. 3
setting No. 3
Setting to determine whether or not to have the
echo suppressor tone in the high-speed
modulation mode.
"0": With V29
"1": Without V29
echo suppressor tone in the high-speed
modulation mode.
"0": With V29
"1": Without V29
1
Without V.29
Setting
5
Transmission
Echo suppressor tone
setting No. 4
setting No. 4
Setting to determine whether or not to have the
echo suppressor tone in the high-speed
modulation mode.
"0": With V27
"1": Without V27
echo suppressor tone in the high-speed
modulation mode.
"0": With V27
"1": Without V27
0
With V.27
Communication/
Setting
Setting
6, 7
Reception
Image capacity when
receiving
(Reflect in DIS, Do not
reflect in DTC.)
receiving
(Reflect in DIS, Do not
reflect in DTC.)
This sets the reception resolution capacity when
FAX calls arrive (when sending DIS).
Reflect in DIS, Do not reflect in DTC.
"00": Very fine
"01": Fine
"10": When small
"11": Ordinary lettering
FAX calls arrive (when sending DIS).
Reflect in DIS, Do not reflect in DTC.
"00": Very fine
"01": Fine
"10": When small
"11": Ordinary lettering
0
Very fine
Setting
0
8
Not used
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
Click on the first or last page to see other MX-FXX2 (serv.man2) service manuals if exist.