Sharp MX-FXX2 (serv.man2) Service Manual ▷ View online
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 30
32
1, 2
Reception
Designation of
reception size
(indicating the width of
reception capacity)
reception size
(indicating the width of
reception capacity)
This sets this machine’s receivable document
width that is notified to the other party’s machine
when receiving.
"00": By loaded cassette
"01": A4 width
"10": B4 (A4, B4) width
"11": A3 (A4, B4, A3) width
When using the loaded cassette, width is as
follows depending on the maximum cassette size.
A5/5.5x8.5R size: A4 width
B5 size: B4 width
A4/8.5x11 size: A3 width
8.5x13/8.5x14: A3 width
B4 size: B4 width
11x17: B4/A3 width (changeover by means of the
FAX soft SW)
A3 size: A3 width
A3 width is adopted in cases where a tray capable
of receiving and printing facsimiles is not set and
cases where all cassettes are open.
width that is notified to the other party’s machine
when receiving.
"00": By loaded cassette
"01": A4 width
"10": B4 (A4, B4) width
"11": A3 (A4, B4, A3) width
When using the loaded cassette, width is as
follows depending on the maximum cassette size.
A5/5.5x8.5R size: A4 width
B5 size: B4 width
A4/8.5x11 size: A3 width
8.5x13/8.5x14: A3 width
B4 size: B4 width
11x17: B4/A3 width (changeover by means of the
FAX soft SW)
A3 size: A3 width
A3 width is adopted in cases where a tray capable
of receiving and printing facsimiles is not set and
cases where all cassettes are open.
1
A3
Setting
1
3
Transmission
Training
Setting whether the training in high speed sending
is set to long or short in V.17.
"0": Short
"1": Long
is set to long or short in V.17.
"0": Short
"1": Long
0
Short
4
Reception
Reception gain
changeover when
receiving
changeover when
receiving
Setting to determine the FTT determination
method when confirming TCF reception.
"0": Judge the EQM value to determine if the
received data is 0
"1": Only judge from the EQM value. Accordingly,
TCF confirmation becomes loose
method when confirming TCF reception.
"0": Judge the EQM value to determine if the
received data is 0
"1": Only judge from the EQM value. Accordingly,
TCF confirmation becomes loose
0
"0" receiving & EYE-Q
check
check
Communication/
Setting
Setting
5
Reception
Time out time setting
after starting TCF
signal reception
after starting TCF
signal reception
The time for time out is set after starting TCF
signal reception.
"0": 4 seconds
"1": 2 seconds
signal reception.
"0": 4 seconds
"1": 2 seconds
0
4 seconds
Setting
6
Communication
Time between DCS-
TCF
TCF
Setting to determine how many seconds in the
interval between DCS transmission and sending
of the TCF signal.
"0": 75msec
"1": 150msec
75±20ms in the ITU-T standard.
interval between DCS transmission and sending
of the TCF signal.
"0": 75msec
"1": 150msec
75±20ms in the ITU-T standard.
0
75ms
Adjustment
value
value
7, 8
Communication
300bps preamble send
time
time
The preamble send time is set in the FSK signal
sending.
"00": 0.5 seconds
"01": 1 second
"10": 1.5 seconds
"11": 2 seconds
sending.
"00": 0.5 seconds
"01": 1 second
"10": 1.5 seconds
"11": 2 seconds
0
1 second
1
33
1, 2
Transmission
Phase-C head dummy
data send time
data send time
Setting of the time to send the dummy data until
sending the head data when sending in Phase-C.
"00": 0.3 seconds
"01": 0.4 seconds
"10": 0.5 seconds
"11": 0.2 seconds
When the dummy data send time is increased, the
remote machine which receives data can easily
detect high speed signals.
sending the head data when sending in Phase-C.
"00": 0.3 seconds
"01": 0.4 seconds
"10": 0.5 seconds
"11": 0.2 seconds
When the dummy data send time is increased, the
remote machine which receives data can easily
detect high speed signals.
0
0.3 seconds
0
3
Communication
Error handling when
transmission and
receiving RTN
transmission and
receiving RTN
Setting to determine whether or not to recognize
communication errors when receiving RTN
signals (only in the V.17 mode).
"0": Recognize errors during RTN reception
"1": Do not recognize error during RTN reception
communication errors when receiving RTN
signals (only in the V.17 mode).
"0": Recognize errors during RTN reception
"1": Do not recognize error during RTN reception
0
Recognize errors
Setting
4, 5
Reception
SED ON level when
receiving
receiving
Setting of an indication of the receivable level
when receiving FAX signals. When noises are
picked up and PPR occurs frequently, set to
"-43dBm" or greater. (For example, "-38dBm.")
"00: -48dBm
"01: -38dBm
"10: -33dBm
"11: -43dBm
when receiving FAX signals. When noises are
picked up and PPR occurs frequently, set to
"-43dBm" or greater. (For example, "-38dBm.")
"00: -48dBm
"01: -38dBm
"10: -33dBm
"11: -43dBm
0
-48dBm
0
6, 7
Transmission
Transmission cable
amplitude equalizer
amplitude equalizer
When sending FAX signals, apply different gain
from the frequency to the data signals between
the modem and line. Setting to determine how
high to make the 4000Hz gain compared to 0Hz.
"00": 0dB
"01": 4dB
"10": 8dB
"11": 12dB
Indispensable in Australia
from the frequency to the data signals between
the modem and line. Setting to determine how
high to make the 4000Hz gain compared to 0Hz.
"00": 0dB
"01": 4dB
"10": 8dB
"11": 12dB
Indispensable in Australia
0
0dB
Communication/
Adjustment
value
Adjustment
value
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 31
Functions
33
8
Not used
0
34
1, 2
Reception
Receive cable
amplitude equalizer
amplitude equalizer
When FAX signals are received, a gain different
from the frequency is applied to the data signals
between the MODEM and the line. Setting of how
much greater the gain of 4000Hz is set when
compared with 0Hz.
"00": 0dB
"01": 4dB
"10": 8dB
"11": 12dB
from the frequency is applied to the data signals
between the MODEM and the line. Setting of how
much greater the gain of 4000Hz is set when
compared with 0Hz.
"00": 0dB
"01": 4dB
"10": 8dB
"11": 12dB
0
0dB
0
3-8
Not used
0
0
0
0
0
0
0
0
0
0
0
35
1-8
Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
36
1
Not used
0
2
Communication
F.A.S.T function
This sets the management function performed in
the FAX communication procedure through the
telephone line.
"0": No
"1": Yes
Valid only in North America.
the FAX communication procedure through the
telephone line.
"0": No
"1": Yes
Valid only in North America.
0
No
3
Print
Print setting when
there is no
communication record
table data
there is no
communication record
table data
Setting to determine whether the record table is
printed or not in the list printing from the system
when there is no record data (history) which have
not printed in printing of the communication
record table.
The list printing from the system setting is as
follows:
• Print output by selecting from the data list print
• Time specification print from the FAX setting or
printed or not in the list printing from the system
when there is no record data (history) which have
not printed in printing of the communication
record table.
The list printing from the system setting is as
follows:
• Print output by selecting from the data list print
• Time specification print from the FAX setting or
print at memory full
"0": Do not print
→ "No print data" is displayed and printing of a list
→ "No print data" is displayed and printing of a list
is disabled.
"1": Print
→ A list is printed though there is no new history.
→ A list is printed though there is no new history.
This setting is used to check that there is no
new history.
new history.
0
Do not print
4
Print
Report output (when
cancelled)
cancelled)
Setting to determine whether or not to output the
communication results sheet in cases where
document transmission is cancelled while in
progress.
"0": Do not output
"1": Output
communication results sheet in cases where
document transmission is cancelled while in
progress.
"0": Do not output
"1": Output
0
Do not output
5
Print
Report output (when
refusing reception)
<FAX only>
refusing reception)
<FAX only>
Setting to determine whether or not to output the
communication results sheet when reception is
refused in FAX reception. However, other than not
printing is set by means of the report output (when
receiving) setting.
"0": Do not output
"1": Output
Internet FAX is set by means of SW63-2.
Irrespective of "Always print" and "Error," the
results sheet is not printed.
communication results sheet when reception is
refused in FAX reception. However, other than not
printing is set by means of the report output (when
receiving) setting.
"0": Do not output
"1": Output
Internet FAX is set by means of SW63-2.
Irrespective of "Always print" and "Error," the
results sheet is not printed.
0
Do not output
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 32
36
6
Print
Printing of transmitted
document contents at
times of F code
communication
<FAX only>
document contents at
times of F code
communication
<FAX only>
Setting to determine whether or not to print part of
the transmitted document on the communication
results sheet at times of F code communication.
However, only when the "Document contents
printing at times of transmission" setting is valid.
"0": Do not print
"1": Print
The "Document contents printing (results sheet)
at times of transmission" setting takes priority.
the transmitted document on the communication
results sheet at times of F code communication.
However, only when the "Document contents
printing at times of transmission" setting is valid.
"0": Do not print
"1": Print
The "Document contents printing (results sheet)
at times of transmission" setting takes priority.
0
Do not print
7
Print
Document content print
when sending (PC-Fax
(Internet Fax) report
table)
when sending (PC-Fax
(Internet Fax) report
table)
Setting to print images or not on the report table
when sending PC-Fax (Internet Fax).
"0": Not print
"1": Print
When the system setting is set so that images are
added in the communication report table, if the
destination is a PC-Fax (Internet Fax), the
document contents are printed by this setting.
when sending PC-Fax (Internet Fax).
"0": Not print
"1": Print
When the system setting is set so that images are
added in the communication report table, if the
destination is a PC-Fax (Internet Fax), the
document contents are printed by this setting.
1
Print
8
Not used
0
37
1, 2
Function
Protocol monitor
Setting to determine whether or not the protocol
monitor (recognized by the FAX) for 1
communication is printed.
"00": No (do not print)
"01": No (do not print)
"10": Print (always)
"11": Only at times of error (print)
When a new communication occurs before the
protocol monitor is printed, delete the old protocol
data (overwrite).
monitor (recognized by the FAX) for 1
communication is printed.
"00": No (do not print)
"01": No (do not print)
"10": Print (always)
"11": Only at times of error (print)
When a new communication occurs before the
protocol monitor is printed, delete the old protocol
data (overwrite).
0
No (do not print)
0
3
Function
Determination of sub-
scan length
(determination setting
when selecting the
page)
scan length
(determination setting
when selecting the
page)
Setting to determine whether to give priority to
width or length when selecting the optimum sheet
when printing received data.
"0": Priority to data length
"1": Priority to data width
width or length when selecting the optimum sheet
when printing received data.
"0": Priority to data length
"1": Priority to data width
0
Priority to data length
4
Print
Paper selection when
reception printing
(LTR/A4)
reception printing
(LTR/A4)
Used to set whether LTR is confirmed first of all in
selection of paper for reception printing or paper
that provides smaller reduction rate of A4 and
LTR is selected.
"0": Priority on LTR/A4 reduction rate
"1": Priority on LTR
selection of paper for reception printing or paper
that provides smaller reduction rate of A4 and
LTR is selected.
"0": Priority on LTR/A4 reduction rate
"1": Priority on LTR
0
Priority on LTR/A4
reduction rate
reduction rate
5
Not used
0
6
Function
Valid/Invalid setting of
FAX A4, 8.5 x 11
threshold
FAX A4, 8.5 x 11
threshold
When printing received FAX data with A4 and 8.5
x 11 paper in the tray, this setting determines
whether to make threshold values in paper
selection valid or invalid. If made valid, it becomes
easier to select letters.
"0": Valid
"1": Invalid
When printing received Internet FAX data,
conduct setting using the separate SW (Valid/
Invalid setting of Internet FAX A4, 8.5 x 11
threshold).
x 11 paper in the tray, this setting determines
whether to make threshold values in paper
selection valid or invalid. If made valid, it becomes
easier to select letters.
"0": Valid
"1": Invalid
When printing received Internet FAX data,
conduct setting using the separate SW (Valid/
Invalid setting of Internet FAX A4, 8.5 x 11
threshold).
0
Valid
7
Reception
Setting of the reception
width of 11x17 sheet
width of 11x17 sheet
This sets the receivable document width in cases
where "11 x 17 sheet" is selected as the FAX
printing paper.
"0": A3 width (A3, B4, A4)
"1": B4 width (B4, A4)
where "11 x 17 sheet" is selected as the FAX
printing paper.
"0": A3 width (A3, B4, A4)
"1": B4 width (B4, A4)
0
A3 width
8
Not used
0
38
1-4
Function
Magnification setting in
automatic reduction
automatic reduction
Setting to determine the page length for reduced
printing of documents received when automatic
reduced printing is set at permitted.
Percentage threshold that can be reduced
(excluding reduction between fixed page sizes)
Setting can be made over the range of 85% to
100% in 1% increments by binary inputting (N x
1% + 85%).
The initial value of 90% is reverted to if a value
outside of the setting range is set.
printing of documents received when automatic
reduced printing is set at permitted.
Percentage threshold that can be reduced
(excluding reduction between fixed page sizes)
Setting can be made over the range of 85% to
100% in 1% increments by binary inputting (N x
1% + 85%).
The initial value of 90% is reverted to if a value
outside of the setting range is set.
0
90%
1
0
1
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 33
38
5
Print
Rotated printing
Setting to determine whether or not to rotate and
output received data when this is possible at
times of receiving and printing FAX and Internet
FAX data.
"0": Permitted (rotate and print)
"1": Prohibited (do not rotate and print)
output received data when this is possible at
times of receiving and printing FAX and Internet
FAX data.
"0": Permitted (rotate and print)
"1": Prohibited (do not rotate and print)
0
Permitted
6
Print
Designation of rotation
direction when printing
on both sides and the
rear side.
direction when printing
on both sides and the
rear side.
Setting to determine whether to adopt vertical
binding or horizontal binding when printing on
both sides.
When horizontal binding is selected, the header
position on both sides (front and rear) is printed in
the same direction.
When vertical binding is selected, since the image
rotates by 180 degrees, the header position is
reversed.
"0": Horizontal binding
"1": Vertical binding
binding or horizontal binding when printing on
both sides.
When horizontal binding is selected, the header
position on both sides (front and rear) is printed in
the same direction.
When vertical binding is selected, since the image
rotates by 180 degrees, the header position is
reversed.
"0": Horizontal binding
"1": Vertical binding
0
Horizontal binding
7
Function
Setting of received
document output when
receiving
document output when
receiving
Setting to determine whether to output data
received in FAX, Internet FAX communications en
masse or to output 1 page at a time as it is
received.
"0": Save and output en masse following
completion of reception
"1": Output 1 page at a time
received in FAX, Internet FAX communications en
masse or to output 1 page at a time as it is
received.
"0": Save and output en masse following
completion of reception
"1": Output 1 page at a time
0
Save and output en
masse following
completion of reception
masse following
completion of reception
8
Print
Selection of error page
output when error
occurs during FAX
reception.
output when error
occurs during FAX
reception.
Setting to determine whether to output the error
page or to not output it and discard it in cases
where communication errors occur during FAX
reception.
"0": Output the error page
"1": Do not output the error page
However, in cases where errors occur during F
code relay-instructed reception or F code
confidential reception, the error page is not
outputted irrespective of this SW setting.
page or to not output it and discard it in cases
where communication errors occur during FAX
reception.
"0": Output the error page
"1": Do not output the error page
However, in cases where errors occur during F
code relay-instructed reception or F code
confidential reception, the error page is not
outputted irrespective of this SW setting.
0
Output the error page
39
1
Transmission
Selection of re-send
page at times of error
page at times of error
Select the page to be re-sent when errors occur
during transmissions that do not contain F code.
"0": Error page and onwards (re-send from the
pages that have not been transmitted to the other
party’s machine).
"1": All pages (re-send from the first page
including pages that have been transmitted to the
other party’s machine).
When transmitting in F code, all pages are re-
transmitted irrespective of this setting.
during transmissions that do not contain F code.
"0": Error page and onwards (re-send from the
pages that have not been transmitted to the other
party’s machine).
"1": All pages (re-send from the first page
including pages that have been transmitted to the
other party’s machine).
When transmitting in F code, all pages are re-
transmitted irrespective of this setting.
0
Error page and onwards
2
Print
Selection of date and
transmission source
print language
<Format>
transmission source
print language
<Format>
Setting to determine the format of the date and
transmission source attached when transmitting
FAX.
"0": Date format
"1": North American format
transmission source attached when transmitting
FAX.
"0": Date format
"1": North American format
0
Date format
3
Print
Relay data output
Setting to determine whether or not to output
documents received from the relay command
station when F code relay broadcast instructions
are received.
"0": Output
"1": Do not output
documents received from the relay command
station when F code relay broadcast instructions
are received.
"0": Output
"1": Do not output
0
Output
4
Transmission
F code relay broadcast
FAX sender addition
setting
FAX sender addition
setting
Setting to determine whether the machine's
sender is added or not when relay broadcast send
is performed to the FAX remote machines which
are registered in the machine (relay broadcast
instruction receiving station) after receiving the F
code relay broadcast instruction is received from
a remote machine.
This is in order to cope with the FAX circular
specifications.
"0": Added
"1": Not added
sender is added or not when relay broadcast send
is performed to the FAX remote machines which
are registered in the machine (relay broadcast
instruction receiving station) after receiving the F
code relay broadcast instruction is received from
a remote machine.
This is in order to cope with the FAX circular
specifications.
"0": Added
"1": Not added
0
Added
5
Communication
F code communication
error handling
error handling
Setting to determine whether or not to re-send at
times of F code communication.
"0": Re-send
"1": Do not re-send
However, do not re-call in cases where the "Re-
call permission at times of communication error"
setting is at "0: Prohibited."
Do not re-send when the other party’s machine
does not have F code functions.
times of F code communication.
"0": Re-send
"1": Do not re-send
However, do not re-call in cases where the "Re-
call permission at times of communication error"
setting is at "0: Prohibited."
Do not re-send when the other party’s machine
does not have F code functions.
0
Re-send
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
Click on the first or last page to see other MX-FXX2 (serv.man2) service manuals if exist.