Sharp MX-FXX2 (serv.man2) Service Manual ▷ View online
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 42
68
3-6
Calling
Pause time setting
(between dials)
(between dials)
This sets the time per pause inputted during dialling.
The pause time can be set from 1 to 15 seconds in 1-
second increments by binary inputting N over the
range of 0 to 15 (1 second x N).
If a value outside the setting range (or "0000") is set,
the initial value of 2 seconds is reverted to.
The pause time can be set from 1 to 15 seconds in 1-
second increments by binary inputting N over the
range of 0 to 15 (1 second x N).
If a value outside the setting range (or "0000") is set,
the initial value of 2 seconds is reverted to.
0
"0010": 2 seconds
(Other country)
"0100": 4 seconds
(South Africa)
(Other country)
"0100": 4 seconds
(South Africa)
FAX initial
setting/
Adjustment
value
setting/
Adjustment
value
0
1
1
0
7, 8
Calling
PBX setting
Setting to determine whether or not to send out ID or
Flash before dialing.
Functions only in Germany and France.
In other countries, this setting is fixed to "OFF".
"00": OFF
"01": Flash
"10": ID
The setting other than the above would be granted
as the default.
Flash before dialing.
Functions only in Germany and France.
In other countries, this setting is fixed to "OFF".
"00": OFF
"01": Flash
"10": ID
The setting other than the above would be granted
as the default.
0
OFF
FAX initial
setting
setting
0
69
1-4
Calling
ID (number) setting
<Input the 1st digit
when dial inputting and
dialing>
<Input the 1st digit
when dial inputting and
dialing>
Conduct ID No. setting when the PBX function is
valid.
Valid when ID is set using SW68-7, 8.
The initial value of 0 is reverted to if a value outside
of the setting range (10 - 15) is set.
valid.
Valid when ID is set using SW68-7, 8.
The initial value of 0 is reverted to if a value outside
of the setting range (10 - 15) is set.
0
0
FAX initial
setting
setting
0
0
0
0
0
5-8
Calling
ID (number) setting 2
<Input the 2nd digit
when dial inputting and
dialing>
<Input the 2nd digit
when dial inputting and
dialing>
Conduct ID No. setting when the PBX function is
valid.
Valid when ID is set using SW68-7, 8.
When 10 - 12, 14, 15 are designated, do not use
numbers with those digits.
"-" when 13 is set.
valid.
Valid when ID is set using SW68-7, 8.
When 10 - 12, 14, 15 are designated, do not use
numbers with those digits.
"-" when 13 is set.
1
-
FAX initial
setting
setting
1
0
0
1
70
1-4
Calling
ID (number) setting 3
<Input the 3rd digit
when dial inputting and
dialing>
<Input the 3rd digit
when dial inputting and
dialing>
Conduct ID No. setting when the PBX function is
valid.
Valid when ID is set using SW68-7, 8.
When 10 - 12, 14, 15 are designated, do not use
numbers with those digits.
"-" when 13 is set.
valid.
Valid when ID is set using SW68-7, 8.
When 10 - 12, 14, 15 are designated, do not use
numbers with those digits.
"-" when 13 is set.
1
-
FAX initial
setting
setting
1
0
0
1
5-8
Call arrival
Distinctive ring (DRD
setting)
setting)
Setting to determine whether or not to execute FAX
arrival call by the distinctive ring.
Even if a call signal other than the set pattern is
detected, there will be no automatic arrival call.
"0000": OFF
"0001": STANDARD
"1000": Pattern 1
"0100": Pattern 2
"1100": Pattern 3
"0010": Pattern 4
"1010": Pattern 5
"0110": ON (Australia)
"1110": ON (New Zealand)
"1001": ON (Hong Kong)
When contents other than the above are set, the
initial value is reverted to.
arrival call by the distinctive ring.
Even if a call signal other than the set pattern is
detected, there will be no automatic arrival call.
"0000": OFF
"0001": STANDARD
"1000": Pattern 1
"0100": Pattern 2
"1100": Pattern 3
"0010": Pattern 4
"1010": Pattern 5
"0110": ON (Australia)
"1110": ON (New Zealand)
"1001": ON (Hong Kong)
When contents other than the above are set, the
initial value is reverted to.
0
OFF
FAX initial
setting/
Setting
setting/
Setting
0
0
0
71
1
Not used
1
2-5
Call arrival
Setting of the number
of automatic reception
calls
of automatic reception
calls
Set the number of call sounds until the start of
receiving (holding of the line) when automatic
reception is set.
This can be set from 0 to 15 (Europe/Indonesia/
Thailand: 0 to 9, Australia/New Zealand: 2 to 4) times
by binary inputting.
If 0 is set, the call sound will not be sounded.
(However, this does not include the nighttime FAX
mode.)
receiving (holding of the line) when automatic
reception is set.
This can be set from 0 to 15 (Europe/Indonesia/
Thailand: 0 to 9, Australia/New Zealand: 2 to 4) times
by binary inputting.
If 0 is set, the call sound will not be sounded.
(However, this does not include the nighttime FAX
mode.)
0
2 times
FAX
reception
setting/
Setting
reception
setting/
Setting
0
1
0
6
Call arrival
Setting for changing
over to automatic
reception during
manual reception
over to automatic
reception during
manual reception
Setting to determine whether or not to initiate
automatic reception after the ringer sounds a certain
number of times when manual reception is set.
"0": Prohibited (do not changeover)
"1": Permitted (changeover)
automatic reception after the ringer sounds a certain
number of times when manual reception is set.
"0": Prohibited (do not changeover)
"1": Permitted (changeover)
0
Prohibited
FAX
reception
setting/
Setting
reception
setting/
Setting
7, 8
Not used
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 43
72
1-5
Call arrival
Setting of the number
of calls for changing
over from manual to
automatic reception
of calls for changing
over from manual to
automatic reception
Set the number of calls before changing over to
automatic reception when in the manual reception
mode.
Functions only in France.
This functions when the "Setting for changing over to
automatic reception during manual reception"
(SW71-6) is valid.
Setting can be made over the range of 1 to 9 times in
1 time increments by binary inputting.
The initial value is reverted to if a value outside of the
setting range is set.
automatic reception when in the manual reception
mode.
Functions only in France.
This functions when the "Setting for changing over to
automatic reception during manual reception"
(SW71-6) is valid.
Setting can be made over the range of 1 to 9 times in
1 time increments by binary inputting.
The initial value is reverted to if a value outside of the
setting range is set.
0
9 times
FAX
reception
setting/
Setting
reception
setting/
Setting
1
0
0
0
6
Communication
ECM (valid except
during V.34: reflected
in the V.21 DIS/DCS/
DTC)
during V.34: reflected
in the V.21 DIS/DCS/
DTC)
Setting to determine whether or not to execute the
error re-send mode.
However, this is only valid when communication is
other than V.34.
"0": Yes. Set with ECM function.
"1": No. Set with no ECM function.
ECM is on during communication in the V.34 mode.
error re-send mode.
However, this is only valid when communication is
other than V.34.
"0": Yes. Set with ECM function.
"1": No. Set with no ECM function.
ECM is on during communication in the V.34 mode.
0
Yes
FAX initial
setting
setting
7
Function
Change from the
image send screen to
the copy screen
image send screen to
the copy screen
Setting to determine whether or not to automatically
change from the image send screen to the copy
screen.
When changing over, if no keys are operated for 20
seconds after pushing the final key in the image send
mode, the copy mode will be automatically switched
to.
If there is no changeover, the machine will remain in
the image send mode and not switch to the copy
mode.
"0": Do not change over
"1": Change over
change from the image send screen to the copy
screen.
When changing over, if no keys are operated for 20
seconds after pushing the final key in the image send
mode, the copy mode will be automatically switched
to.
If there is no changeover, the machine will remain in
the image send mode and not switch to the copy
mode.
"0": Do not change over
"1": Change over
1
"1": Change over
(North America)
"0": Do not change over
(Other country)
(North America)
"0": Do not change over
(Other country)
Operation
setting
setting
8
Function
Image quality setting
when saving (FAX)
when saving (FAX)
Setting to determine whether or not to make filed
image quality valid (initial setting for image quality
selection when transmitting filed document files by
FAX)
"0": Do not apply
"1": Apply
image quality valid (initial setting for image quality
selection when transmitting filed document files by
FAX)
"0": Do not apply
"1": Apply
0
Do not apply.
73
1-4
Function
Image quality priority
selection (standard
image quality setting)
selection (standard
image quality setting)
Setting to determine the initial setting for image
quality selection when reading documents on the
FAX.
"0000": Ordinary lettering
"0001": Small lettering
"0010": Fine
"0011": Very fine
"0101": Small lettering, medium tone
"0110": Fine, medium tone
"0111": Very fine, medium tone
"Ordinary lettering" (initial value) is reverted to if a
value outside of the setting range is set.
quality selection when reading documents on the
FAX.
"0000": Ordinary lettering
"0001": Small lettering
"0010": Fine
"0011": Very fine
"0101": Small lettering, medium tone
"0110": Fine, medium tone
"0111": Very fine, medium tone
"Ordinary lettering" (initial value) is reverted to if a
value outside of the setting range is set.
0
Ordinary lettering
Operation
setting
setting
0
0
0
5
Function
Received data printing
hold (FAX/Internet
FAX)
hold (FAX/Internet
FAX)
Setting to determine whether or not to store data
received by FAX/Internet FAX in the memory without
outputting it.
"0": Do not hold
"1": Hold
received by FAX/Internet FAX in the memory without
outputting it.
"0": Do not hold
"1": Hold
0
Do not hold
Operation
setting
setting
6
Function
Saving the setting
contents for a certain
period after completion
of scanning
contents for a certain
period after completion
of scanning
Setting to determine whether the set values of the
destination and various functions are saved without
returning to the default values or not when
reservation is completed on the image send screen.
"0": The set values are not saved.
"1": The set values are saved.
destination and various functions are saved without
returning to the default values or not when
reservation is completed on the image send screen.
"0": The set values are not saved.
"1": The set values are saved.
0
The set values are not
saved.
saved.
Operation
setting
setting
7
Not used
0
8
Function
Default finish stamp
setting
setting
Setting to determine whether the finish stamp is used
or not after completion of document scan when the
document feed unit (RSPF) is used.
"0": NO (The finish stamp is not used.)
"1": YES (The finish stamp is used.)
or not after completion of document scan when the
document feed unit (RSPF) is used.
"0": NO (The finish stamp is not used.)
"1": YES (The finish stamp is used.)
0
NO
Operation
setting
setting
74
1-4
Function
Speaker volume when
on-hook (Speaker
volume during DTMF
sending)
on-hook (Speaker
volume during DTMF
sending)
This sets speaker volume for when the on-hook
button is pushed.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," it is considered as setting to the
default.
button is pushed.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," it is considered as setting to the
default.
1
8
FAX initial
setting
setting
0
0
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 44
74
5-8
Function
Call sound volume
Irrespective of whether there is a handset, this sets
the volume of the call sound that is sounded when a
signal arrives.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
the volume of the call sound that is sounded when a
signal arrives.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
1
8
FAX initial
setting
setting
0
0
0
75
1-4
Function
Line monitor volume
setting
setting
Set the speaker volume during line monitoring.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
1
"1000": 8 (Other country)
"0000": 0 (U.K./France/
Germany/Rusia)
"0000": 0 (U.K./France/
Germany/Rusia)
FAX initial
setting
setting
0
0
0
5-8
Function
Volume of the
transmission
completion sound
(Volume of the
successful
transmission sound)
transmission
completion sound
(Volume of the
successful
transmission sound)
Set the volume of the completion sound outputted
from the speaker upon completion of FAX
transmission.
When sending is succeeded, a sound is generated
by this setting.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
from the speaker upon completion of FAX
transmission.
When sending is succeeded, a sound is generated
by this setting.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
1
8
FAX initial
setting
setting
0
0
0
76
1-4
Function
Volume of the
communication error
completion sound
(Volume of the
transmission and
reception error sound)
communication error
completion sound
(Volume of the
transmission and
reception error sound)
This sets the volume of the completion sound
outputted from the speaker upon completion of FAX
communication error.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
outputted from the speaker upon completion of FAX
communication error.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
1
8
FAX initial
setting
setting
0
0
0
5-8
Function
Volume of the
reception completion
sound (Volume of the
reception completion
sound)
reception completion
sound (Volume of the
reception completion
sound)
This sets the volume of the completion sound
outputted from the speaker upon completion of FAX
reception.
When receiving is succeeded, a sound is generated
by this setting.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
outputted from the speaker upon completion of FAX
reception.
When receiving is succeeded, a sound is generated
by this setting.
The sound volume is set with a value. The greater
the value is, the greater the sound volume is.
Setting range is 1 (small) to 15 (large) by binary
input.
When it is set to "0," there is no sound (OFF).
1
8
FAX initial
setting
setting
0
0
0
77
1, 2
Function
Tone of the successful
transmission sound
transmission sound
This sets the tone sounded when transmission is
successful.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
successful.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
1
Pattern 3 (1000Hz)
FAX initial
setting
setting
0
3, 4
Function
Tone of the
transmission and
reception error sound
transmission and
reception error sound
This sets the tone sounded when there is a
transmission and reception error.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
transmission and reception error.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
1
Pattern 3 (1000Hz)
FAX initial
setting
setting
0
5, 6
Function
Tone of the reception
sound
sound
This sets the tone sounded upon completion of
reception.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
reception.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
1
Pattern 3 (1000Hz)
FAX initial
setting
setting
0
7
Function
Auto startup mode
In the case where FAX or Internet FAX is received
during nighttime mode or simulated mode, if this
setting is ON, the received document will be
outputted when the machine becomes able to output.
When OFF, the machine will receive the data by
proxy without outputting the document, but it will
output the received document when the panel power
SW is ON.
"0": Setting (setting for automatically starting up the
main unit and outputting)
"1": Release (setting for storing in the memory
without starting up the main unit)
during nighttime mode or simulated mode, if this
setting is ON, the received document will be
outputted when the machine becomes able to output.
When OFF, the machine will receive the data by
proxy without outputting the document, but it will
output the received document when the panel power
SW is ON.
"0": Setting (setting for automatically starting up the
main unit and outputting)
"1": Release (setting for storing in the memory
without starting up the main unit)
0
Setting
FAX initial
setting
setting
8
Not used
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
MX-FXX2 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 45
78
1-3
Function
Setting of the
successful
transmission sound
time
successful
transmission sound
time
This sets the time the tone is sounded when
transmission is successful.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the
setting range is set.
transmission is successful.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the
setting range is set.
0
3.0 seconds
FAX initial
setting
setting
1
0
4-6
Function
Setting of the reception
sound time
sound time
This sets the time the tone is sounded upon
completion of reception.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the
setting range is set.
completion of reception.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the
setting range is set.
0
3.0 seconds
FAX initial
setting
setting
1
0
7
Function
Setting of the time of
the transmission/
reception error sound
the transmission/
reception error sound
Transmission error sound sounding interval
"0": Every 0.3 seconds
"1": Every 0.7 seconds
Sounding time and paper feeding time are the same.
"0": Every 0.3 seconds
"1": Every 0.7 seconds
Sounding time and paper feeding time are the same.
0
Every 0.3 seconds
FAX initial
setting
setting
8
Not used
0
79
1, 2
Print
Communication results
sheet print settings (for
ordinary transmission)
<FAX only>
sheet print settings (for
ordinary transmission)
<FAX only>
This sets outputting of the communication results
sheet following transmission (excluding successive
broadcast, successive polling and relay broadcast
transmission).
"00": Do not print
"01": Always print
"10": At times of transmission failure
The initial value is reverted to if a value outside of the
setting range is set.
sheet following transmission (excluding successive
broadcast, successive polling and relay broadcast
transmission).
"00": Do not print
"01": Always print
"10": At times of transmission failure
The initial value is reverted to if a value outside of the
setting range is set.
1
At times of transmission
failure
failure
FAX initial
setting
setting
0
3, 4
Print
Setting of the
communication results
sheet printing (at times
of broadcast
transmission)
communication results
sheet printing (at times
of broadcast
transmission)
This sets outputting of the communication results
sheet at times of successive broadcast, successive
polling and relay broadcast transmission.
"00": Do not print
"01": Always print
"10": Failed transmission address
The initial value is reverted to if a value outside of the
setting range is set.
sheet at times of successive broadcast, successive
polling and relay broadcast transmission.
"00": Do not print
"01": Always print
"10": Failed transmission address
The initial value is reverted to if a value outside of the
setting range is set.
0
Always print
FAX initial
setting
setting
1
5, 6
Print
Communication results
sheet print setting
(when receiving)
<FAX only>
sheet print setting
(when receiving)
<FAX only>
This sets outputting of the communication results
sheet for when communications are received
(excluding confidential communications).
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the
setting range is set.
sheet for when communications are received
(excluding confidential communications).
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the
setting range is set.
0
Do not print
FAX initial
setting
setting
0
7
Print
Report output (when
receiving confidential
communications)
<FAX only>
receiving confidential
communications)
<FAX only>
Setting to determine whether or not to output the
communication results sheet (receiving) when
confidential communications are received.
"0": Print
"1": Do not print
This only functions when the communication results
sheet print setting (receiving) is set to be outputted.
communication results sheet (receiving) when
confidential communications are received.
"0": Print
"1": Do not print
This only functions when the communication results
sheet print setting (receiving) is set to be outputted.
0
Print
FAX initial
setting
setting
8
Not used
0
80
1, 2
Print
Print document
contents when
transmitting (results
sheet)
<FAX only>
contents when
transmitting (results
sheet)
<FAX only>
Setting to determine whether or not to print part of
the transmitted document on the communication
results sheet (transmission) when FAX transmission
error occurs.
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the
setting range is set.
This functions when the communication results sheet
print setting (ordinary transmission) (broadcast
transmission) is set to be outputted.
the transmitted document on the communication
results sheet (transmission) when FAX transmission
error occurs.
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the
setting range is set.
This functions when the communication results sheet
print setting (ordinary transmission) (broadcast
transmission) is set to be outputted.
1
At times of error
FAX initial
setting
setting
0
SW
No.
No.
Bit
No.
Item
SW selection and function
Initial value
System
settings
Click on the first or last page to see other MX-FXX2 (serv.man2) service manuals if exist.