DOWNLOAD Sharp MX-BMX1 Service Manual ↓ Size: 22.28 MB | Pages: 127 in PDF or view online for FREE

24 November 2010 

BOOKLET MAKER INSTALLATION

1.  Connect the communication cable [A] from the finisher ( 

 x1), to the Book-

let maker.

2.  Connect the Belt Stacker cable [B] ( 

 x1). 

NOTE: Unless Trimmer MX-TMX1 and/or Book Folder MX-FDX2 will be in-

stalled. If so, Belt Stacker cable will be connected to the last module in the 

system.

3.  Install the Terminator plug [C] and the Interlock jumper [G].

NOTE: The Terminators and Interlock jumpers are stored in the installation kit.

4.  Install the Terminator plug [D] and the Interlock jumper [F]. 

NOTE: Unless Trimmer MX-TMX1 will be installed. If so, communication cable 

and power cord between MX-BMX1 and MX-TMX1 will be connected.

5.  Connect the powercord [E] to the Booklet maker ( 

 x1).

6.  Mount the cable protector [H] positioned as shown with two screws in the 

holes [I] and route the cables inside the cable protector (   x 2).

7.  Attach the sticker “Do not lift here” [J] on the cable protector.
8.  Install the cable holders on the rear of the Booklet Maker and route the cables 

through them.

[B]

[A]

[C]

[D]

[E]

[F]

[G]

[H]

[I]

[J]

24 November 2010

BOOKLET MAKER INSTALLATION

1.  If installing a Cover Feeder MX-CFX3 or Trimmer MX-TMX1, continue to that 

section ( 

 1.4 or 1.5 ) otherwise continue with step 2.

2.  Turn on the power for the Booklet maker.

NOTE: Make sure that the finisher connector is connected to the copier.

3.  Remove the two Stapler heads, according to section ( 

 3.4.12 ).

4.  Perform a Detailed self-diagnostic, according to section ( 

 5.3.3 )

5.  Reinstall the two Stapler heads, according to section ( 

 3.4.12 ).

6.  Turn on the power for the Copier.

NOTE: Make sure that the Booklet maker is powered ON before the Copier.

7.  Set up the Booklet maker to Auto paper size.
8.  Send one A4/8.5 x 11” job to the Booklet maker.
9.  Check for the correct feeding of the paper.

NOTE: If paper is not fed correctly, check adjustment of the Booklet maker ac-

cording to section ( 

 1.3.3 ).

10.  Send one A3/11 x 17” job to the Booklet maker.
11.  Check for the correct feeding of the paper.

NOTE: If paper is not fed correctly, check adjustment of the Booklet maker ac-

cording to section ( 

 1.3.3 ).

24 November 2010 

COVER FEEDER INSTALLATION

Check the quantity and condition of the accessories in the box against the follow-

ing list:

A.  Cover Feeder module, MX-CFX3 .........................................  1
B.  Feeder roller  ........................................................................  1
C.  DSD Calibration strip ............................................................  1

[A]

[B]

[C ]

24 November 2010

COVER FEEDER INSTALLATION

1.  Remove all parts from the box.
2.  Cut the cable tie [A] to release the paper bin and DSD Calibration strip [B].
3.  Place the DSD Calibration strip on the cable holder [C] behind the Booklet 

Maker rear cover.

[B]

[C]

[A]