DOWNLOAD Sharp MX-BMX1 Service Manual ↓ Size: 22.28 MB | Pages: 127 in PDF or view online for FREE

24 November 2010 

COVER FEEDER INSTALLATION

1.  Turn on the power for the Booklet Maker.
2.  Enter the service mode on the Booklet Maker by pressing and holding the 

leftmost menu button while powering on the Booklet Maker. 

NOTE: Do not enter the service mode through the Tools menu.

3.  Enter the password.
4.  Scroll down to MX-CFX3 Service and press OK.
5.  Press the CHG button, so the “Installed:” is set to YES.
6.  Press OK.
7.  Perform a Cover Feeder motors Calibration according to section ( 

 5.5 ).

8.  Perform a Cover Feeder DSD sensor Calibration according to section ( 

 

5.5 ).

9.  Make sure that the stapler heads are removed, according to section 

( 

 Service Manual MX-BMX1 3.4.12 ).

10.  Perform a self diagnosis.
 

- Scroll up to Diagnostic and press OK.

 

- Press the RUN button.

 

- If the Diagnostic is OK, continue.

11.  Power off the Booklet Maker.
12.  Reinstall the stapler heads according to section ( 

 Service manual MX-

BMX1 3.4.12 ).

24 November 2010

COVER FEEDER INSTALLATION

1.  If installing a Trimmer MX-TMX1 continue to section ( 

 1.5 ) otherwise 

continue with step 2.

2.  Turn on the power for the Booklet maker.

NOTE: Make sure that the finisher connector is connected to the copier.

3.  Turn on the power for the Copier.

NOTE: Make sure that the Booklet maker is powered ON before the Copier.

4.  Prepare a 15mm high stack of A4/8.5 x 11” covers.
5.  Make sure that the ink has dried out well, to avoid smearing.
6.  Make sure that the covers are well fanned to avoid misfeeds or double-feeds.
7.  Align the covers well to achieve a reliable collating operation and good finish-

ing result.

8.  Press down the green marks on Paper bin and load the covers.
9.  Move the adjustable side guides up against the covers, until there is no clearance.
10.  Set up the Cover Feeder to Cover ON, the fan will start and the Cover Feeder 

will prefeed the first cover to be ready for the set from the copier.

11.  Set up the Booklet maker to A4/8.5 x 11” paper size.
12.  Send one A4/8.5 x 11” job to the Booklet maker system.
13.  Check for the correct feeding of the set from the finisher.

NOTE: The paper should enter in the middle of the infeeder. If not, adjust the 

Booklet maker according to section ( 

 1.3.3 ).

14.  Check that the covers are correctly fed into the Booklet maker.
15.  Set up the Cover Feeder to Cover OFF and remove all covers from the bin. 

Use the Purge mode to completely empty the Cover Feeder from covers.

16.  Prepare a 15mm high stack of A3/11 x 17” covers.
17.  Repeat step 5 to 10.
18.  Set up the Booklet maker to A3/11 x 17” paper size.
19.  Send one A3/11 x 17” job to the Booklet maker system.
20.  Check for the correct feeding of the set from the finisher.

NOTE: The paper should enter in the middle of the infeeder. If not, adjust the 

Booklet maker according to section ( 

 1.3.3 ).

21.  Check that the covers are correctly fed into the Booklet maker.

24 November 2010 

TRIMMER INSTALLATION

[A]

Check the quantity and condition of the accessories in the box against the follow-

ing list:

NOTE: - The Installation Box is located in the trim bin on the Trimmer. 

- The trim bin is tie wrapped on the rear. 

- Trimmer fan is bubble wrapped and located inside the Trimmer. 

- The Rail Extension is located in the packing material

A.  Communication cable between the Booklet maker ..............  1 

  and the Trimmer
B.  Powercord between the Booklet maker and Trimmer ..........  1
C.  Rail extension  ......................................................................  1 

  Plugs and screws  ................................................................  4
D.  Cable protector .....................................................................  1
E.  Cable protector sticker .........................................................  1
F.  Cable holder .........................................................................  1

[B]

[C]

[D]

[E]

[F]

24 November 2010

TRIMMER INSTALLATION

1.  Remove all parts from the pallets.
2.  Ensure all of the packing material is removed from the outside of the Trimmer.
3.  Tilt the Trimmer to upright position.