DOWNLOAD Sharp MX-BM50 (serv.man2) Service Manual ↓ Size: 25.75 MB | Pages: 127 in PDF or view online for FREE

Model
MX-BM50 (serv.man2)
Pages
127
Size
25.75 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Latest Service Manual inc Installation Instructions
File
mx-bm50-sm2.pdf
Date
PREV: Sharp MX-BM50 Drivers

Sharp MX-BM50 (serv.man2) Service Manual ▷ View online

11 Feb 2013 
Replacement  Adjustment
COVERS
BM-3-13
 
 
COVERS
REP  3.3.6  TOP COVER ASSEMBLY
[A]
[B]
Removal
1.  Remove Front and Rear cover ( 
 REP  3.3.1).
2.  If a Cover Feeder is installed - disconnect connectors (plugs) [A] ( 
 x2).
3.  Squeeze the barbs on the sides and remove connectors (jacks) [B] from Top 
cover ( 
 x2).
continued on next page
11 Feb 2013
BM-3-14
 
 
COVERS
4.  Note position of the adjustment plates [G] in regard to the screws holding nuts [C].  
Remove nuts [C] (   x4 ).
5.  Note position of screws [D] and [E] in regard to the cut-outs.  
Remove screws [D] and [F] (   x2 ).
6.  Move Top cover towards the front side.
7.  Note position of screws [F] in regard to the adjustment plates [G].  
Remove screws [F](   x2 ) and adjustment plates [G] ( x2 ).
8.  Lift off the Top cover.
Replacement
1.  Reverse the removal procedure.
[C]
[D]
[C]
[F]
[E]
[G]
[G]
REP  3.3.6 TOP COVER ASSEMBLY, CONTINUED
continued on next page
11 Feb 2013 
Replacement  Adjustment
COVERS
BM-3-15
 
 
COVERS
Adjustment
1.  Make sure that the Top cover rests on the rubber supports [H] ( x3 ) when closed.  
Loosen screw [D], [E] and screws [F] to adjust.
2.  Check that the Top cover lock works without binding.
3.  Check that the Top cover Interlock switch is correctly adjusted ( 
 REP  3.3.7).
[H]
REP  3.3.6 TOP COVER ASSEMBLY, CONTINUED
11 Feb 2013
BM-3-16
 
 
COVERS
REP  3.3.7  INTERLOCK SWITCH BM-SW1 (SW16/SW17)
Removal
1.  Remove Front cover ( 
REP  3.3.1 ).
2.  Note position and remove connectors [A] ( 
 x4 ).
3.  Remove screws [B] to remove interlock box (   x4 ).
Replacement
1.  Reverse the removal procedure.
Adjustment
 
Correctly adjusted (figure 1), the hooks [C] should stay locked under the rollers [D]
so that the Top cover stays locked without play after the Top cover is closed. The 
metal switch actuator [E] on the Top cover should not touch the Interlock switch 
[F]. The handle [G] should be flush with the Top cover surface.
[A]
SW1.2 SW1.4 SW1.3 SW1.1
[B]
[C]
[B]
[D]
[F]
[E]
[G]
figure 1
[H]
continued on next page
Page of 127
Display

Click on the first or last page to see other MX-BM50 (serv.man2) service manuals if exist.

RANDOM: