Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ▷ View online
MX-5111N MX-LC11 (LARGE CAPACITY TRAY) 6 – 4
6)
In the case of a shift to the left, lift the grip so that the height
adjustment check rib is in the same line with the axis line of the
mounting plate upper, and insert the large capacity tray unit.
adjustment check rib is in the same line with the axis line of the
mounting plate upper, and insert the large capacity tray unit.
7)
Tighten the loosened screw.
D. Connector connection
1)
Remove the screw, and remove the connector cover.
2)
Connect the connector, and tighten the screw.
E. Paper size switch
(1) Paper size switch from A4 to LT
Since the factory setting of the paper size is A4, if paper size switch
is required, perform the following procedures.
1)
is required, perform the following procedures.
1)
Slowly pull out the tray until it stops.
2)
Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.
of the tray so that the stopper does not function.
3)
Pull out the tray again until it stops.
MX-5111N MX-LC11 (LARGE CAPACITY TRAY) 6 – 5
a. Side plate size switch
1)
1)
Remove four fixing screws (blue screws) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.
upper and the lower sections of the side plate F and the side
plate R.
2)
Adjust the mark position of the tray and the side plates in the
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).
b. Auxiliary guide size switch
1)
1)
When switching the size of the side plate R, check to confirm
the mark position ( ) of the side plate R and the size guide
adjustment plate.
the mark position ( ) of the side plate R and the size guide
adjustment plate.
2)
Loosen the fixing screw (flat screw 1pc) of the auxiliary guide.
3)
Set the mark position ( ) of the auxiliary guide and the cas-
sette R to the size from A4 to LT, and fix with the fixing screw
(flat screw).
sette R to the size from A4 to LT, and fix with the fixing screw
(flat screw).
At that time, set the mark position ( ) of the auxiliary guide
and the cassette R to the same scale of the mark position ( )
of the side plate R and the size guide adjustment plate con-
firmed in procedure 1). (If the scale of the size guide adjust-
ment plate is at the center, set it to the center. If the size guide
adjustment plate is in 1mm in the front side, set it in 1mm in the
front side.)
and the cassette R to the same scale of the mark position ( )
of the side plate R and the size guide adjustment plate con-
firmed in procedure 1). (If the scale of the size guide adjust-
ment plate is at the center, set it to the center. If the size guide
adjustment plate is in 1mm in the front side, set it in 1mm in the
front side.)
c. Rear edge shaft switch
1)
1)
Remove the rear edge shift fixing screw (blue screw) which is
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
2)
Tighten the removed rear edge shaft with the fixing screw
(blue), and store it in the storage space inside the front cabi-
net.
(blue), and store it in the storage space inside the front cabi-
net.
F side
R side
F side
R side
A4
LT
2
1
MX-5111N MX-LC11 (LARGE CAPACITY TRAY) 6 – 6
3)
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
tion, and fix the fixing screw.
At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.
with the stopper reception of the large capacity tray unit.
4)
Slowly insert the tray to the original position.
(2) Paper size switch from A4 to B5
Since the factory setting of the paper size is A4, if paper size switch
is required, perform the following procedures.
1)
is required, perform the following procedures.
1)
Slowly pull out the tray until it stops.
2)
Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.
of the tray so that the stopper does not function.
3)
Pull out the tray again until it stops.
a. Side plate size switch
1)
1)
Remove four fixing screws (blue screws) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.
upper and the lower sections of the side plate F and the side
plate R.
2)
Adjust the mark position of the tray and the side plates in the
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).
F side
R side
MX-5111N MX-LC11 (LARGE CAPACITY TRAY) 6 – 7
b. Auxiliary guide size switch
* Since the auxiliary guide setting is not required, fix the auxiliary
* Since the auxiliary guide setting is not required, fix the auxiliary
guide to either of A4 or LT. (To prevent against missing of the
part)
part)
c. Rear edge shaft switch
1)
1)
Remove the rear edge shift fixing screw (blue screw) which is
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
2)
Insert the removed rear edge shaft into the mounting hole in
the paper feed desk as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.
the paper feed desk as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.
NOTE: When the rear edge shaft is switched to B5, check to con-
firm that the side plates F/R are already set to B5. If the
side plates F/R are not set to B5, the rear edge shaft can-
not be switched to B5.
side plates F/R are not set to B5, the rear edge shaft can-
not be switched to B5.
3)
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
tion, and fix the fixing screw.
At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.
with the stopper reception of the large capacity tray unit.
4)
Slowly insert the tray to the original position.
F. Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
F side
R side
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) service manuals if exist.