Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ▷ View online
MX-5111N Dehumidifying heater 3 – 7
2)
Install the table glass. Install the SPF glass and the glass
holder, and secure it with the screw.
holder, and secure it with the screw.
F. Installation of the desk heater kit
(1) Assembling of the desk heater
1)
Attach the desk heater (package part No. 20) to the heater
heat sink (package part No. 21), and secure it with the screw
(M3x4 S-tight) (package part No. 22).
heat sink (package part No. 21), and secure it with the screw
(M3x4 S-tight) (package part No. 22).
2)
Attach the heater heat sink to the desk heater mounting plate
(packing part No. 23), and secure it with the screw (M3x4 S-
tight) (packing part No.22).
Attach the edge wire saddle (packing part No. 24) and pass the
desk harness through it.
(packing part No. 23), and secure it with the screw (M3x4 S-
tight) (packing part No.22).
Attach the edge wire saddle (packing part No. 24) and pass the
desk harness through it.
(2) Removal of the tray, the desk rear cabinet, the rear
cover of the main unit
1)
Remove the tray 3 and the tray 4.
2)
Remove the screw, and remove the desk rear cabinet and the
rear cover of the main unit.
rear cover of the main unit.
(3) Installation of the desk heater unit
1)
Attach the desk heater unit to the desk frame, and secure it
with the screw (M3x6 S-tight) (package part No. 25).
Pass the harness of the desk heater through the hole on the
desk frame.
with the screw (M3x6 S-tight) (package part No. 25).
Pass the harness of the desk heater through the hole on the
desk frame.
MX-5111N Dehumidifying heater 3 – 8
2)
Attach the caution label (package part No. 26) to the desk
frame.
frame.
NOTE: Wipe the surface where the label is to be affixed with alco-
hol, then attach the label along the mark.
3)
Secure the earth wire of the desk heater harness (package
part No. 27) to the desk frame with the screw (M4x8 K) (pack-
age part No. 28).
part No. 27) to the desk frame with the screw (M4x8 K) (pack-
age part No. 28).
NOTE: When installing, put the direction of the earth wire terminal
within the reference range.
4)
Attach the mini clamp (package part No.29).
Attach the snap band of the desk heater harness to the desk
frame, and connect the desk heater harness to the harness of
the desk heater.
Attach the snap band of the desk heater harness to the desk
frame, and connect the desk heater harness to the harness of
the desk heater.
(4) Installation of the tray, the desk rear cabinet and
the rear cover of the main unit
1)
Install the desk rear cabinet to the desk heater tray that pulled
out, and secure it with the screw.
out, and secure it with the screw.
NOTE: Put out the desk heater harness from the notch part of the
desk rear cabinet.
2)
Connect the desk heater harness to the main unit.
3)
Split the main unit rear cover along the perforated line, then
attach it to the main unit, and secure it with the screw.
attach it to the main unit, and secure it with the screw.
Reference mark
Reference
mark
mark
Reference
MX-5111N Dehumidifying heater 3 – 9
G. Installation of the LCC heater kit
(1) Paper feed unit removal
1)
Pull out the paper feed tray.
2)
Open the upper cover.
3)
Remove the upper cabinet.
4)
Disconnect the connector, and remove the paper feed unit.
(2) Heater cover and cabinet removal
1)
Remove the heater cover.
2)
Remove the cabinet.
(3) Heater attachment
1)
Attach the heater.
1
1
2
2
3
1
2
1
2
1
1
2
1
2
2
1
MX-5111N Dehumidifying heater 3 – 10
2)
Attach the protect sheet.
(4) Heater harness unit attachment
1)
Attach the snap band of the heater harness unit. While holding
the harness upward, attach the AC cord fixer.
the harness upward, attach the AC cord fixer.
NOTE: After attaching the snap band, cut and trim the end of the
band.
NOTE: Be careful not to mistake the attaching direction of the AC
cord fixer.
2)
Pull the harness tightly in the arrow direction, and check to
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
3)
Connect the connector of the heater harness unit, and attach
the earth wire.
the earth wire.
NOTE: Attach the earth wire at an angle of 45 degrees.
(5) Cabinet and heater cover attachment
1)
Attach the cabinet.
2)
Attach the heater cover.
75
˴5mm
r
0
˴
2mm
㨪
1
2
45q
2
1
2
1
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) service manuals if exist.