Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ▷ View online
MX-5111N MX-4110N/5110N/4111N/5111N/4112N/5112N (MAIN UNIT) 2 – 2
2. Installation
Note before installation
* When connecting the main unit with the optional STAND/1 X 500
* When connecting the main unit with the optional STAND/1 X 500
SHEET PAPER DRAWER or STAND/2 X 500 SHEET PAPER
DRAWER, first unpack and install the PAPER DRAWER then
unpack the main unit and securely place the main unit on the
PAPER DRAWER before installing the main unit.
DRAWER, first unpack and install the PAPER DRAWER then
unpack the main unit and securely place the main unit on the
PAPER DRAWER before installing the main unit.
A. Lock release
(1) Tray rotation plate lock release
1)
Pull out the tray. Turn the fixing material and remove it.
Remove the caution label.
Attach the removed fixing material to the position shown in the
figure for future use.
Close the tray which was pulled out.
Remove the caution label.
Attach the removed fixing material to the position shown in the
figure for future use.
Close the tray which was pulled out.
(2) Scanner (2/3 mirror unit) lock release
1)
Remove the optical unit fixing screw, and remove the note
label.
label.
B. Developing (each color) installation
Be careful not to attach fingerprints or oily dirt on the DV roller sur-
face.
1)
face.
1)
Open the front cabinet, and remove the waste toner box.
2)
Check that the lock is released as shown in (A).
Loosen the blue screw, and open the drum positioning unit.
* When the lock is not released, use a screwdriver to turn the
Loosen the blue screw, and open the drum positioning unit.
* When the lock is not released, use a screwdriver to turn the
screw (B) counterclockwise so that it is fit as (A).
3)
Open the DV lock lever, and release the fixing screw.
(1position for each color)
(1position for each color)
4)
Pinch the knob and remove the development unit.
2
1
3
2
1
A
B
1
2
MX-5111N MX-4110N/5110N/4111N/5111N/4112N/5112N (MAIN UNIT) 2 – 3
5)
Remove the screws.
6)
Hold the sections A, and remove the DV cover in the arrow
direction (B).
direction (B).
7)
Supply developer (Packed items) in the developer unit.
* Shake the bag of developer with unopened state. After stir-
* Shake the bag of developer with unopened state. After stir-
ring toner and developer in the bag, supply it to the develop-
ing unit.
ing unit.
* When replacing developer, use an extreme care not to drop
developer on the drive section (marked with ()).
8)
Install the DV cover in the arrow direction A.
* When installing the DV cover, be sure to engage the pawl
* When installing the DV cover, be sure to engage the pawl
with the boss.
9)
Secure the DV cover with the two screws.
10) Shake the developer unit horizontally a few times.
* When supplying developer, do not tilt the developing unit.
A
A
B
A
A
MX-5111N MX-4110N/5110N/4111N/5111N/4112N/5112N (MAIN UNIT) 2 – 4
11) Install each developer unit.
* When installing the developer unit, be sure to check that the
DV lock lever is open.
12) Secure with fixing screw. Lower the DV lock lever until it clicks
closed.
13) Close the drum positioning unit, and tighten the blue screw.
14) Install the waste toner box.
C. Set the control level for the reference toner
density
1)
With the front cabinet open, connect the power plug to the
power outlet.
power outlet.
2)
Turn ON the main power switch of the machine and the power
switch on the operation panel.
switch on the operation panel.
3)
Enter the SIM25-2 mode.
4)
After entering the simulation, close the front cabinet.
5)
Select K, C, M, Y and then press the [EXECUTE] button. The
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density. (Operating times: approx. 3 minutes)
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density. (Operating times: approx. 3 minutes)
MEMO: Be sure to select all of the four colors: K, C, M, Y
6)
After the machine completes cycling, exit the simulation mode
by pressing the [CA] key on the main unit.
by pressing the [CA] key on the main unit.
D. Installation of individual color toner cartridges
* The life of each toner cartridge is as follows:
Black toner cartridge: equivalent to approximately 40K (A4/LT
5%)
Color toner cartridge: equivalent to approximately 18K (A4/LT
5%)
5%)
Color toner cartridge: equivalent to approximately 18K (A4/LT
5%)
1)
Shake the toner cartridge horizontally several times.
1
2
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$8720$7,&'(9(/23(5$'-8670(17
(;(&87(
$7'(9($'-B/B.
$7'(9(92B0B.
$7'(9($'-B/B&
$7'(9(92B0B&
$7'(9($'-B/B0
$7'(9(92B0B0
$7'(9($'-B/B<
$7'(9(92B0B<
$7'(9($'-B0B.
$7'(9($'-B0B&
$7'(9($'-B0B0
$7'(9($'-B0B<
$7'(9(92B/B.
$7'(9(92B/B&
$7'(9(92B/B0
$7'(9(92B/B<
.
&
0
<
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$8720$7,&'(9(/23(5$'-8670(17
(;(&87(
$7'(9($'-B/B.
$7'(9(92B0B.
$7'(9($'-B/B&
$7'(9(92B0B&
$7'(9($'-B/B0
$7'(9(92B0B0
$7'(9($'-B/B<
$7'(9(92B0B<
$7'(9($'-B0B.
$7'(9($'-B0B&
$7'(9($'-B0B0
$7'(9($'-B0B<
$7'(9(92B/B.
$7'(9(92B/B&
$7'(9(92B/B0
$7'(9(92B/B<
.
&
0
<
MX-5111N MX-4110N/5110N/4111N/5111N/4112N/5112N (MAIN UNIT) 2 – 5
2)
Open the front cabinet, and pull the toner cartridge out slowly
and horizontally.
and horizontally.
* Be sure to install the color cartridges to their proper posi-
tions. Avoid installation to a different color position.
* Do not forcibly insert the toner cartridge.
Keep holding the cartridge and completely insert it.
* When the machine is transported with the developing unit
removed, be sure to remove the toner cartridge. (If not, toner
may be clogged.)
Color toner cartridge positions
may be clogged.)
Color toner cartridge positions
3)
Insert the cartridge securely until it locks.
* Push it until the click sound is heard.
* Push it until the click sound is heard.
E. Cleaning of LSU's dust-proof glass
* Dust from the transfer belt or shutter or some other adjacent part
may fall onto the LSU during transport or installation. Be sure to
clean the dust-proof glass before checking the image quality.
clean the dust-proof glass before checking the image quality.
1)
Open the front cabinet, and remove the waste toner box.
2)
Detach the LSU cleaning bar from the front cover.
3)
Turn the felt side of the cleaning bar downward and insert it.
Slide it back and forth a few times to clean the LSU dust-proof
glass.
Slide it back and forth a few times to clean the LSU dust-proof
glass.
4)
Replace the LSU claning bar to the front cover and attach the
waste toner box. Close the front cabinet.
waste toner box. Close the front cabinet.
Yellow
Magenta
Cyan
Black
2
1
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) service manuals if exist.