Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ▷ View online
MX-5111N Dehumidifying heater 3 – 3
2)
Remove the snap band. Insert the supporter (package part No.
3) to the frame of the power unit, and attach the WH PWB
(package part No. 4) on it.
3) to the frame of the power unit, and attach the WH PWB
(package part No. 4) on it.
NOTE: Be careful not to break the PWB when mounting the PWB
to the supporters.
3)
Connect the harness to the WH PWB.
4)
Connect the AC-WH harness 1 (package part No. 5) to the AC
PWB, the WH PWB and the dehumidifier heater switch.
PWB, the WH PWB and the dehumidifier heater switch.
NOTE: The AC-WH harness 1 should pass under the MSW har-
ness.
C. Installation of the heater kit
(1) Assembling of the heater unit
1)
Attach the heater (package part No. 6) to the heater mounting
plate (package part No. 7), and secure it with the screw (M3x6
S-tight) (package part No. 8).
plate (package part No. 7), and secure it with the screw (M3x6
S-tight) (package part No. 8).
2)
Attach the heater mounting plate to the T-Heater cover (pack-
age part No. 9), and secure it with the screw (M3x6 S-tight)
(package part No. 8).
Attach the snap band of the heater harness to the T-Heater
cover.
age part No. 9), and secure it with the screw (M3x6 S-tight)
(package part No. 8).
Attach the snap band of the heater harness to the T-Heater
cover.
NOTE: After installing, check that the harness of the heater go
straight into the T-Heater cover.
3)
Attach the caution label (package part No. 10) to the T-Heater
cover.
cover.
NOTE: Wipe the surface where the label is to be affixed with alco-
hol, then attach the label along the reference line.
Reference line
Reference
line
line
MX-5111N Dehumidifying heater 3 – 4
(2) Installation of the heater unit
1)
Remove the tray 1 and the tray 2.
2)
Install the heater unit to the main unit, and secure it with the
screw (M3x5 S-tight) (package part No.11).
Pass the harness of the heater through the hole on the main
unit frame, and attach the snap band.
screw (M3x5 S-tight) (package part No.11).
Pass the harness of the heater through the hole on the main
unit frame, and attach the snap band.
3)
Pass the harness of heater that arrange behind the main body
through the wire saddle, and connect it to the WH PWB.
Bind the harness of the heater and the AC-DC WH harness
with the omega lock (package part No. 12).
through the wire saddle, and connect it to the WH PWB.
Bind the harness of the heater and the AC-DC WH harness
with the omega lock (package part No. 12).
4)
Attach the core (This procedure only applies to the 200V
series 41cpm).
Attach the AC-cable connection plate (only for 120V series), or
attach the inlet mounting plate (only for 230V series). Secure it
with screw.
series 41cpm).
Attach the AC-cable connection plate (only for 120V series), or
attach the inlet mounting plate (only for 230V series). Secure it
with screw.
NOTE: When installing, be careful to biting the wire.
D. Installation of the rear cabinet and the left rear
lower cabinet
1)
Install the left rear lower cabinet and secure it with the screw.
2)
Install the rear cabinet and secure it with the screw.
120V Series
200V Series 41cpm
MX-5111N Dehumidifying heater 3 – 5
E. Installation of the scanner heater kit
(1) Assembling of the scanner heater unit
1)
Secure the marking position on the harness of the scanner
heater (package part No.13) to the heater fixing plate (package
part No.14) with the banding band (package part No.15).
heater (package part No.13) to the heater fixing plate (package
part No.14) with the banding band (package part No.15).
2)
Extend the harness, and secure the other position of it with
banding band (packing part No.15).
banding band (packing part No.15).
3)
Tighten the snap band and cut its tip to approx. 5 mm or less.
Slide the banding band head to the square hole (Part that is
enclosed by the mark).
Slide the banding band head to the square hole (Part that is
enclosed by the mark).
NOTE: The banding band head and cut tip must not protrude
behind the heater fixing plate.
(2) Removal of the table glass, the paper exit cover
1)
Remove the screw, and remove the SPF glass and the glass
holder. Remove the table glass.
holder. Remove the table glass.
2)
Remove the paper exit cover.
(3) Installation of the scanner heater unit
1)
Attach the clamp (package part No. 16) to the scanner frame.
NOTE: When installing, be careful to prevent damage of the wire.
MX-5111N Dehumidifying heater 3 – 6
2)
Remove two screws from the scanner bottom.
3)
Connect the harness of the scanner heater. Install the heater
fixing plate of the scanner heater unit, and secure it with the
screw (M3x4 Round-tipped) (package part No. 17).
fixing plate of the scanner heater unit, and secure it with the
screw (M3x4 Round-tipped) (package part No. 17).
4)
Install the scanner heater and secure it with the screw (M4x6
Bind machine screw) (package part No. 18). Pass the harness
through the clamp.
Bind machine screw) (package part No. 18). Pass the harness
through the clamp.
NOTE: The convex part of the scanner heater must be inserted
into the hole of the scanner frame.
5)
Tighten the loose scanner heater harness by pulling it in the
arrow direction and secure it with the snap band (packing part
No. 19) then cut its tip to approx. 5 mm or less.
arrow direction and secure it with the snap band (packing part
No. 19) then cut its tip to approx. 5 mm or less.
6)
Move the lamp unit by hand and check that it move smoothly in
all movable area.
all movable area.
NOTE: Check that there is no interference of the harness of the
scanner heater in the wire and the 2/3 mirror unit.
(4) Installation of the table glass, the paper exit cover
1)
Install the paper exit cover.
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) service manuals if exist.