DOWNLOAD Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ↓ Size: 30.84 MB | Pages: 127 in PDF or view online for FREE

MX-5111N  MX-LC11 (LARGE CAPACITY TRAY)  6 – 8

Execute SIM 26-2 "Size setting" with the key operations of the main
unit.
1)

The size selection menu of the large capacity tray is displayed
on the operation message display.

2)

Select a size button to be set on the message screen.

1)

 Run SIM 50-10 using the keypad on the main unit. 
 The following screen appears. 

2)

This screen allows you to configure the print off-center adjust-
ment value for each paper feed tray. 

3)

On the touch panel, press [

] to select "G: 50 :MAIN-LCC." 

4)

Enter the desired adjustment value through the numeric key-
pad. 
(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
• Reducing the adjustment value by 1 causes the main scan/

print position to shift by 0.1 mm toward the rear. 

• Increasing the adjustment value by 1 causes the main scan/

print position to shift by 0.1 mm toward the front. 

5)

After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting. 

6)

Check that the adjustment pattern image is printed in the cor-
rect position.
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met: 

No adjustment is needed if A - B = 0 

 3.0 mm.

If the above condition is not met, do the following:

7)

Change the adjustment value. 
(Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm. 
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied. 

8)

After you have completed the adjustment, exit from simulation
mode by pressing the [CA] key.

Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
removed, perform the following adjustment procedures.
1)

Slowly pull out the tray until it stops.

2)

Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.

3)

Pull out the tray again until it stops.

ǂǂǂ6,08/$7,21ǂǂ12

7(67

3$3(5&(17(52))6(76(783

$˖

˷̚
˹

˖%.0$*

$˖

˖0$,10)7

%˖

˖0$,1&6

&˖

˖0$,1&6

'˖

˖0$,1&6

)˖

˖0$,1&6

(˖

˖0$,1/&&

*˖

˖0$,1$'8

+˖

˖68%0)7

,˖

˖68%&6

-˖

˖68%&6

.˖

˖68%/&&

/˖

2.

&/26(

(;(&87(

A-B = 0

3.0mm

+

-

B

A

MX-5111N  MX-LC11 (LARGE CAPACITY TRAY)  6 – 9

a. When the shift is in the front side
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)

Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction A (R side) by the shift amount, and tighten
the red fixing screws (2 for each). Move the auxiliary guide in
the direction A by the same size.

Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.

2)

Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.

b. When the shift is in the rear side
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)

Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction B (F side) by the shift amount, and tighten
the red fixing screws (2 for each). Restore the stopper to the
original position, and fix it with the fixing screws. Move the aux-
iliary guide in the direction B by the same size.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.

2)

Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.

A

R side

F side

B

R side

F side

MX-5111N  MX-TRX2 (EXIT TRAY UNIT)  7 – 1

MX-5111N

Service Manual

 

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Open the right door. Remove the screw, and remove the con-
nector cover.

2)

Remove the screw. Disengage the engagement in the front
side then in the rear side, and remove the paper exit cover.

3)

Connect the connector, and install the exit roller unit (Packed
items). Use the screw which was removed in step 3) and fix
the unit.

4)

Install the connector cover, and fix it with the screw.

1

Exit roller unit

1

2

Full detection actuator

1

1

2

MX-5111N  MX-TRX2 (EXIT TRAY UNIT)  7 – 2

5)

Install the exit tray unit (A) and the full detection actuator (B)
(Packed items). 
* Be careful of the installing direction of the full detection actu-

ator.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

Use SIM26-1 to set the tray YES/NO.