Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man9) Service Manual ▷ View online
MX-4070N MX-FN29 (SADDLE STITCH FINISHER) 11 – 4
4)
Bring the finisher near the main unit, and connect them.
5)
Install the finisher fixing screw.
6)
Close the front cover of the finisher.
7)
Unscrew the screw of the connector cover of the man unit, and
remove the connector cover.
remove the connector cover.
Front
Right side
Be careful not to fix
with the screw here.
with the screw here.
Push the lock lever.
Move the lock lever to
the upper side.
the upper side.
MX-4070N MX-FN29 (SADDLE STITCH FINISHER) 11 – 5
8)
Fix the plate with the tied cables to the main unit with the screw
(M3x6), and connect the connector of the harness. Tie the har-
ness of the interface unit and the harness of the finisher with the
clamp, and fix it.
(M3x6), and connect the connector of the harness. Tie the har-
ness of the interface unit and the harness of the finisher with the
clamp, and fix it.
9)
Fix the connector cover of the main unit with the screw.
F. Installation of the saddle stitch finisher
The basic installation procedure is the same as the finisher.
Only the installation method of the saddle tray is different.
1)
Lift the paper fixing arm, and install the saddle tray.
2)
Lower the paper fixing arm.
MX-4070N MX-PN15B/C/D (PUNCH MODULE) 12 – 1
MX-4070N
Service Manual
[12] MX-PN15B/C/D (PUNCH MODULE)
1. Unpacking
A. Removal of the punch unit
B. Packed items check
No.
Name
Quantity
1
Punch unit
1
2
Resist sensor
1
3
Guide plate
1
4
Hopper
1
5
Stay
1
6
Hopper
1
7
Stepping motor
1
8
Harness
1
9
Screw
15
1
: ‘16/Feb.
1
MX-4070N MX-PN15B/C/D (PUNCH MODULE) 12 – 2
2. Installation
NOTE: Be sure to install the punch unit before installing the finisher to
the main unit. In the case of installing the punch unit afterward,
remove the finisher from the main unit once.
remove the finisher from the main unit once.
NOTE: Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the
power outlet. Make double sure that the data lamp on the
operation panel does not light up or blink when performing
installation.
power outlet. Make double sure that the data lamp on the
operation panel does not light up or blink when performing
installation.
A. Installation of the punch unit
1)
Remove the tapes from the packing materials.
2)
When the finisher is connected to the main unit, disconnect the
interface cable and remove the finisher.
interface cable and remove the finisher.
3)
Remove the rear cabinet of the finisher.
4)
Incline the upper part of the rear cabinet, and remove the rear
cabinet while lifting the pawls of the rear cabinet.
cabinet while lifting the pawls of the rear cabinet.
5)
Open the front cabinet of the finisher.
6)
Remove the knob.
7)
For MX-FN29 (Saddle finisher), remove the knob.
8)
Unscrew the screw fixing the inner cover.
Lift the pawls.
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man9) service manuals if exist.