DOWNLOAD Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man8) Service Manual ↓ Size: 21.98 MB | Pages: 88 in PDF or view online for FREE

MX-2300/2700 N/G  MX-FXX1  19 – 4

1) Switch the operation panel to the copy mode and use the key

operation [P], [

∗], [C], and [∗] to enter the simulation mode.

2) Use the numeric keys to enter [66] in the main code entry

screen shown below and press the [START] key.

3) Use the numeric keys to enter [10] in the sub-code entry

screen shown below and press the [START] key.

4) In the submenu screen shown below, press [EXECUTE] on the

touch panel.
After [YES] on the panel lights up, press it.

5) The screen shown below is displayed and memory clear oper-

ation is executed.

6) After several minutes, memory clear operation is completed

and the [YES] button goes out. Press the [CA] key to exit from
the simulation mode.
Then the main unit is automatically rebooted.

Connect the line cable of the line side to the modular jack indicated
with “LINE.”

• For using an external telephone:

For using an external telephone, wind the line cable around the
supplied ferrite core by two turns and connect the cable to the
modular jack indicated with “TEL.”

MX-2300/2700 N/G  MX-FWX1  20 – 1

MX2700N

Service Manual

 

<Note before installation>
• In order to enable the Internet Fax send function, the product key

must be acquired.

• In order to specify the address of the Internet Fax with the PC-

FAX driver, the PC-FAX driver must be updated by the Internet
Fax expansion kit.

1) In order to enable the Internet Fax send function, enter the

product key by the key operation on the operation panel.
For entry of the product key, refer to the item of the product key
entry of the system setting guide.

2) After completion of entry of the product key, turn OFF the

power switch of the main unit and the main power switch, then
turn ON the power switch and the main power switch.
After completion of 1) and 2), the Internet Fax send function
from the main unit becomes enable. To enable the Internet Fax
send with the PC-FAX driver, the following steps 3) and 4) are
required.

3) Use the CD-ROM packed together with the machine to install

the PC-FAX driver.
For installing procedures, refer to the software setup guide.

4) Update the PC-FAX driver with the CD-ROM packed together

with the machine.

Install and setting of the driver to the PC server must be performed
by the user or by the request from the user.

After completion of entry of the product key, check to confirm that
the Internet Fax send is performed normally from the machine.
After completion of update of the PC-FAX driver, press the print
button on the test page of the PC-FAX driver to check to confirm
that the Internet Fax send is performed normally.

1

CD-ROM

1

2

Product key sheet

1

1

2

MX-2300/2700 N/G  MX-SMX1  21 – 1

MX2700N

Service Manual

 

1) Turn OFF the main switch of the copier, and disconnect the

power plug of the copier from the power outlet.

2) Remove the screw, and remove the rear cabinet.

3) Remove the connector and the screw, and remove the MFP

PWB shield plate upper.

4) Install the expansion memory to the connector.

* Note for installing the expansion memory
a)

Push the sections indicated with 

→ at the same time with

both hands.
* When handling the expansion memory, be careful not to

touch the pin section.

* Insert the memory straightly until it comes in contact

with the contact.

* When inserting, be careful not to slant the memory for

the connector. Do not push the memory by one hand
alone.

b)

Push the sections indicated with 

→ at the same time with

both hands until the right and the left buttons are locked.

5)

Install the MFP PWB shield plate upper, and connect the con-
nector.

256MB expansion memory

MX-2300/2700 N/G  MX-SMX1  21 – 2

6) Install the rear cabinet.

7) Insert the power plug of the copier into the power outlet. Turn

ON the power switch.