Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man8) Service Manual ▷ View online
MX-2300/2700 N/G MX-PNX1A/B/C/D 7 – 4
16) Slide the inner finisher to the original position, and close the
front cover.
C. Punch position label attachment
1) Attach the label to the position indicated in the figure.
[For scanner] (package part No. 1)
[For RSPF] (package part No. 2)
D. Turn on the power of the main unit
1)
Connect the earth cord, and insert the power plug of the main
unit into the power outlet.
unit into the power outlet.
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
2
1
Label attachment reference
* Corner of the
"upper cabinet rear"
Corner R end fitting
Corner R end fitting
No clearance
Second label
First label
R2.5 connection line
Edge line R 2.5
CAUTION
Cleaning of the document scan section
When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
Document scan section
ON
ON
ON
MX-2300/2700 N/G MX-RBX1, MX-FNX2 8 – 1
MX2700N
Service Manual
[8] MX-RBX1, MX-FNX2
1. Unpacking the MX-RBX1
A. Removal of the interface pass unit
B. Removal of the fixing tape
1) Remove the fixing tape.
C. Check the packed items
1)
Check that all the items are included in the package.
2. Installing the MX-RBX1
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit.
Turn OFF the power switch in the front cabinet of the main unit.
No.
Packed part names
Quantity
1
Right cover plate
1
2
Interface left cabinet
1
3
Reverse tray
1
4
Fixing screw A
6
5
Fixing screw B
1
6
Ornamental screw
1
7
Reverse detection actuator
1
8
Stopper
1
1
1
2
3
4
5
6
7
8
OFF
OFF
OFF
: Dec. 15 2005
1
MX-2300/2700 N/G MX-RBX1, MX-FNX2 8 – 2
3) Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.
B. Removal of the paper holding arm unit
1) Push up the section A to disengage the pawl, and remove the
paper holding arm and the paper holding arm holder together
as a unit.
* Be careful to remove both of the paper holding arm (which is
as a unit.
* Be careful to remove both of the paper holding arm (which is
easily removed alone) and the paper holding arm holder.
C. Installation of the interface pass unit
1) Open the front cabinet. Remove the screws, and remove the
front cabinet upper.
2)
Disengage the pawls, and remove the paper exit tray cover.
3)
Remove the screws, and remove the paper exit tray.
4)
Remove the paper exit full detection actuator (A), and install
the reverse detection actuator (B) (package part No. 7).
* Be careful of the installing direction of the reverse detection
the reverse detection actuator (B) (package part No. 7).
* Be careful of the installing direction of the reverse detection
actuator.
5)
Engage the projection of the main unit frame with the hole in
the right cover plate (package part No. 1), and install the right
cover plate and fix it with the fixing screw A (package part No.
4).
the right cover plate (package part No. 1), and install the right
cover plate and fix it with the fixing screw A (package part No.
4).
* Be sure to clamp and fix the paper exit tray shifter side plate
with the fixing guide.
2
1
A
1
2
A
B
B
MX-2300/2700 N/G MX-RBX1, MX-FNX2 8 – 3
6) Insert the rib of the interface left cabinet (package part No. 2)
into the slit on the lower surface of the scanner left cabinet.
Install the interface left cabinet with the fixing screw A (pack-
age part No. 4) of the paper exit tray which was removed in
procedure 4).
Install the interface left cabinet with the fixing screw A (pack-
age part No. 4) of the paper exit tray which was removed in
procedure 4).
7) Insert the reverse tray (package part No. 3) along the groove in
the interface left cabinet and the top surface of the right cover
plate.
* When inserting the reverse tray, check to insure that the
plate.
* When inserting the reverse tray, check to insure that the
switch guide of the reverse tray is up.
8) Fix the reverse tray with the ornamental screw (package part
No. 6).
9)
Install the front cabinet upper, and fix with the screws.
10) Fix the stopper (package part No. 8) with the fixing screw B
(package part No. 5).
11) Insert the interface pass unit along the guide rail.
12) Fix the interface pass disconnection preventing lever with the
fixing screw A (package part No. 4).
13) Go to the saddle finisher installing procedure.
Click on the first or last page to see other MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man8) service manuals if exist.