Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man8) Service Manual ▷ View online
MX-2300/2700 N/G MX-RBX1, MX-FNX2 8 – 8
H. Turn on the power of the main unit
1) Connect the earth cord, and insert the power plug of the main
unit into the power outlet.
2) Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
3) Turn ON the power switch on the operation panel.
I. Storage of the paper entry guide
1)
When the punch unit is not installed, store the paper entry
guide (package part No. 7) to the position in the saddle finisher
section as shown in the table below.
Pinch the paper guide with the plate (A), and then insert the
boss (B) in the hole in the paper guide.
guide (package part No. 7) to the position in the saddle finisher
section as shown in the table below.
Pinch the paper guide with the plate (A), and then insert the
boss (B) in the hole in the paper guide.
ON
ON
ON
A
B
B
1
2
MX-2300/2700 N/G AR-PN1A/B/C/D 9 – 1
MX2700N
Service Manual
[9] AR-PN1A/B/C/D
1. Unpacking
A. Removal of the punch unit
B. Check the packed items
1) Check that all the items are included in the package.
* The punch position labels (No.5 and No.6) and must be those
bundled with the MX-FNX2 rather than those bundled with the
AR-PN1A/B/C/D.
AR-PN1A/B/C/D.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit.
Turn OFF the power switch in the front cabinet of the main unit.
3)
Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.
main unit from the power outlet.
4)
Disconnect the connector between the main unit and the sad-
dle finisher.
dle finisher.
No.
Packed part names
Quantity
1
Harness A (Purple)
1
2
Harness B (Orange)
1
3
Fixing screw (M4 x 6 with tooth lock washer)
1
4
Dust box label
1
5
Punch position label (For scanner) *
1
6
Punch position label (For RSPF) *
1
1
2
3
4
5
6
OFF
OFF
OFF
MX-2300/2700 N/G AR-PN1A/B/C/D 9 – 2
B. Installation of the punch unit
1) Release the lock and separate the saddle finisher from the
main unit.
2) Open the front door, and remove the knob.
3) Remove the screws, and remove the front cabinet upper.
4)
Remove the screw, and remove the pawl (A) on the rear cabi-
net in the arrow direction (B), and remove the rear cabinet
upper in the arrow direction (C).
Remove the interface harnesses (2 pcs.) from the outlet port of
the rear cabinet upper.
net in the arrow direction (B), and remove the rear cabinet
upper in the arrow direction (C).
Remove the interface harnesses (2 pcs.) from the outlet port of
the rear cabinet upper.
5)
Remove the screws. Open the top door and remove the right
cabinet upper and the right cabinet middle.
cabinet upper and the right cabinet middle.
6)
Remove the pawls (2 positions) of the upper cover, and sepa-
rate it into the upper and the lower sections. Reuse the upper
section.
rate it into the upper and the lower sections. Reuse the upper
section.
1
2
B
C
A
1
2
MX-2300/2700 N/G AR-PN1A/B/C/D 9 – 3
C. Replacement of the paper entry paper guide
1) Remove the dust box of the punch unit.
2) Remove the guide from the dust box.
The guide is not used in the MX-FNX2.
3) Remove two screws which are fixing the paper entry paper
guide.
4) Remove the hook (boss) on the upper side of the paper entry
paper guide.
5)
Remove the hook (boss) on the upper side of the paper entry
paper guide with a screwdriver.
paper guide with a screwdriver.
6)
Remove the paper entry paper guide.
7)
Install the paper entry paper guide exclusively used for the
MX-FNX2 packed with the saddle finisher.
MX-FNX2 packed with the saddle finisher.
8)
Fix the incoming paper guide using the screws removed in
step 2.
step 2.
9)
Replace the dust box to the original position.
1
2
Click on the first or last page to see other MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man8) service manuals if exist.