Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man20) User Manual / Operation Manual ▷ View online
36
SPECIFYING THE SCAN SIZE OF THE ORIGINAL
If the original is a non-standard size or you wish to change the scan size, touch the [Original] key to specify the original
size manually. Place the original in the document feeder tray or on the document glass and follow the steps below.
size manually. Place the original in the document feeder tray or on the document glass and follow the steps below.
Specifying the size using paper sizes
1
Display the original settings screen.
(1) Touch the [Image Settings] key.
(2) Touch the [Original] key.
The automatically detected size appears at the top of the
[Original] key.
[Original] key.
2
Touch the [Scan Size] key.
3
Specify the scan size.
(1) Touch the appropriate original size key.
(2) Touch the [OK] key.
• If you are sending a long original, touch the [Long Size] key. Use the automatic document feeder to scan a long
original. (When the automatic document feeder is not installed, the [Long Size] key does not appear.) The maximum
length that can be scanned is 800 mm (31-1/2") (the maximum width is 297 mm (11-5/8")).
length that can be scanned is 800 mm (31-1/2") (the maximum width is 297 mm (11-5/8")).
• To specify an inch size for the scan size, touch the [AB
Inch] key to highlight the [Inch] side and then specify the
scan size.
4
Touch the [OK] key.
When [Long Size] is selected, the two-sided scanning setting and send size cannot be changed. In addition, scanning will
take place in Mono 2 mode.
take place in Mono 2 mode.
Quick File
File
Special Modes
Address Entry
Address Book
Scan
Mode Switch
Image
Settings
Send Settings
Auto
Exposure
200X200dpi
Resolution
PDF/PDF
File Format
Special Modes
Original
Auto A4
Mono2/Auto
Colour Mode
(1)
(2)
Scan
Original
Original
100%
OK
Scan Size
Auto A4
2-Sided
Booklet
Booklet
2-Sided
Tablet
Tablet
Send Size
Auto
Image Orientation
Scan
Original
Original
OK
Size Input
Standard Size
Auto
Manual
Manual
B5R
AB
Inch
A5
B4
A3
A4
A5R
A4R
B5
Long Size
(2)
(1)
B5
Scan
Original
Original
OK
Scan Size
Send Size
2-Sided
Booklet
Booklet
2-Sided
Tablet
Tablet
Auto
Image Orientation
100%
37
Specifying the size by entering numerical values.
When scanning a non-standard size original such as a postcard or card, follow these steps to specify the original size.
The width can be from 64 mm to 432 mm (2-1/2" to 17"), and the length can be from 64 mm to 297 mm (2-1/2" to 11-5/8").
The width can be from 64 mm to 432 mm (2-1/2" to 17"), and the length can be from 64 mm to 297 mm (2-1/2" to 11-5/8").
1
Display the original settings screen.
(1) Touch the [Image Settings] key.
(2) Touch the [Original] key.
The automatically detected size appears at the top of the
[Original] key.
[Original] key.
2
Touch the [Scan Size] key.
3
Enter the scan size (original size).
(1) Touch the [Size Input] tab.
(2) Touch the [X] key and enter the X
(horizontal) dimension with the
keys.
(3) Touch the [Y] key and enter the Y (vertical)
dimension with the
keys.
(4) Touch the [OK] key.
System Settings (Administrator): Original Size Detector Setting
This is used to set the size entry screen to "mm units" or "inch units".
This is used to set the size entry screen to "mm units" or "inch units".
4
Touch the [OK] key.
The specified size appears in the [Scan Size] key.
• When the scan size is specified by numerical values, the send size cannot be specified.
• When the automatic document feeder is used, an original longer that 432 mm (17") can be scanned (maximum length 800
mm (31-1/2")). To scan a long original, touch the [Standard Size] tab in the screen of step 3 and then touch the [Long Size]
key.
key.
☞
Specifying the size using paper sizes
(page 36)
Quick File
File
Special Modes
Address Entry
Address Book
Scan
Mode Switch
Image
Settings
Send Settings
Auto
Exposure
200X200dpi
Resolution
PDF/PDF
File Format
Special Modes
Original
Auto A4
Mono2/Auto
Colour Mode
(1)
(2)
Scan
Original
Original
100%
OK
Scan Size
Auto A4
2-Sided
Booklet
Booklet
2-Sided
Tablet
Tablet
Send Size
Auto
Image Orientation
Scan
Original
Original
64
64
OK
Size Input
Standard Size
(64 432)
mm
mm
(64 297)
mm
mm
X
Y
Auto
Manual
Manual
X
Y
(4)
(2), (3)
(1)
Scan
Original
Original
2-Sided
Booklet
Booklet
2-Sided
Tablet
Tablet
OK
Scan Size
Send Size
Auto
Image Orientation
X64 Y64
38
SPECIFYING THE SEND SIZE OF THE ORIGINAL
Specify the send size as a paper size. If a send size bigger than the scan size is selected, the image will be enlarged. If
a send size smaller than the scan size is selected, the image will be reduced.
a send size smaller than the scan size is selected, the image will be reduced.
The send size cannot be specified when [Long Size] is selected for the scan size, or when the scan size is specified by
numerical values.
numerical values.
1
Display the original settings screen.
(1) Touch the [Image Settings] key.
(2) Touch the [Original] key.
2
Touch the [Send Size] key.
3
Specify the send size.
(1) Touch the desired send size key.
(2) Touch the [OK] key.
• Size keys that cannot be specified for the send size are greyed out to prevent selection.
• To specify an inch size for the send size, touch the [AB
Inch] key to highlight the [Inch] side and then specify the
send size.
4
Touch the [OK] key.
The ratio used for reduction or enlargement of the original will
appear between the "Scan Size" and the "Send Size".
appear between the "Scan Size" and the "Send Size".
Quick File
File
Special Modes
Address Entry
Address Book
Scan
Mode Switch
Image
Settings
Send Settings
Auto
Exposure
200X200dpi
Resolution
PDF/PDF
File Format
Special Modes
Original
Auto A4
Mono2/Auto
Colour Mode
(1)
(2)
Auto
100%
OK
Scan Size
Auto A4
Send Size
Image Orientation
Scan
Original
Original
2-Sided
Booklet
Booklet
2-Sided
Tablet
Tablet
Scan
Original
Original
OK
Auto
B5R
AB
Inch
A5
B4
A3
A4
A5R
A4R
B5
Manual
A4
(2)
(1)
A3
141%
Scan
Original
Original
OK
Scan Size
Auto A4
2-Sided
Booklet
Booklet
2-Sided
Tablet
Tablet
Send Size
Image Orientation
39
CHANGING THE COLOUR MODE
This procedure is used to change the colour mode used to scan the original when the [COLOUR START] key (
)
or the [BLACK & WHITE START] key (
) is pressed.
Start key
Mode
Scanning method
[COLOUR START]
key
Auto
The machine detects whether the original is colour or black and white and
automatically selects full colour or black and white (Mono 2 or Greyscale)
scanning.
automatically selects full colour or black and white (Mono 2 or Greyscale)
scanning.
Full Colour
The original is scanned in full colour. This mode is best for full colour
originals such as catalogues.
originals such as catalogues.
[BLACK & WHITE
START] key
Mono2
Colours in the original are scanned as black or white. This mode is best for
text-only originals.
text-only originals.
Greyscale
The colours in the original are scanned in black and white as shades of
grey (greyscale).
grey (greyscale).
1
Display the colour mode screen.
(1) Touch the [Image Settings] key.
(2) Touch the [Colour Mode] key.
2
Select the colour mode.
(1) Touch the key of the mode to be used when
the [COLOUR START] key (
) is
pressed.
You can select whether black & white scanning will take
place in Mono 2 or greyscale when [Auto] is selected and
a black and white original is scanned. Note that if the file
format is set to JPEG, scanning will take place in
greyscale.
place in Mono 2 or greyscale when [Auto] is selected and
a black and white original is scanned. Note that if the file
format is set to JPEG, scanning will take place in
greyscale.
(2) Touch the key of the mode to be used when
the [BLACK & WHITE START] key (
) is
pressed.
(3) Touch the [OK] key.
• System Settings (Administrator): Default Colour Mode Settings
The default colour mode can be changed.
• System Settings (Administrator): Disable Change of B/W Setting in Auto Mode
This prohibits selection of the black and white original scanning setting when [Auto] is selected for the colour mode.
Quick File
File
Special Modes
Address Entry
Address Book
Scan
Mode Switch
Image
Settings
Send Settings
Auto
Exposure
200X200dpi
Resolution
PDF/PDF
File Format
Mono2/Auto
Colour Mode
Special Modes
Original
Auto A4
(1)
(2)
Scan
Colour Mode
Colour Mode
OK
Mono2
B/W
Full Colour
Colour
Greyscale
Greyscale
Colour Mode
B/W Mode
Auto
Mono2
(2)
(1)
(3)
Click on the first or last page to see other MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man20) service manuals if exist.