Sharp DX-C202 User Manual / Operation Manual ▷ View online
Entering Characters
This section describes how to enter characters using the control panel when configuring the machine's
settings.
Use the keys as follows to enter characters.
To enter a digit
settings.
Use the keys as follows to enter characters.
To enter a digit
Press a number key.
To delete a character
Press the [ ] key.
To enter a fax number
• To enter a number
Use the number keys.
• To enter characters other than digits
" ": Press [ ].
" ": Press [ ].
Pause: Press the [Pause/Redial] key. "P" appears on the screen.
Space: Press the [ ] key.
" ": Press [ ].
Pause: Press the [Pause/Redial] key. "P" appears on the screen.
Space: Press the [ ] key.
To enter a name
Letters, numbers, and symbols can be entered using the number keys.
To enter two characters that use the same number key successively, wait briefly after entering the
first character.
To enter two characters that use the same number key successively, wait briefly after entering the
first character.
CES164
• Characters you can enter depend on the setting you are configuring.
Entering Characters
123
• If the number you entered is too large or too small for the setting, it will not be accepted. If you
press the [OK] key, the machine will increase or decrease the number to the minimum or maximum
value for the setting.
value for the setting.
2. Getting Started
124
Restricting Machine Functions According to
User
You can set the machine to require a user code when someone tries to use certain machine functions.
• When print jobs are restricted, you can only authenticate through the PCL printer driver. Printing
from the PostScript 3 printer driver will not be possible.
Use of the following functions can be restricted:
• Copying (both color and black-and-white)
• Color copying
• Sending faxes
• Scan to E-mail/FTP/Folder
• Scan to USB
• PictBridge printing
• Printing (both color and black-and-white)
• Color printing
• Sending faxes via LAN-Fax
• Color copying
• Sending faxes
• Scan to E-mail/FTP/Folder
• Scan to USB
• PictBridge printing
• Printing (both color and black-and-white)
• Color printing
• Sending faxes via LAN-Fax
To enable this setting, you must first configure the machine via Web Image Monitor.
Enabling the User Restriction Settings
This section describes how to set the machine to permit only authorized users to use certain machine
functions.
Using Web Image Monitor, enable user restriction for all or some of the functions listed below, and then
register users who can use those functions.
functions.
Using Web Image Monitor, enable user restriction for all or some of the functions listed below, and then
register users who can use those functions.
• Copying (both color and black-and-white)
• Color copying
• Sending faxes
• Scan to E-mail/FTP/Folder
• Scan to USB
• PictBridge printing
• Printing (both color and black-and-white)
• Color printing
• Sending faxes via LAN-Fax
• Color copying
• Sending faxes
• Scan to E-mail/FTP/Folder
• Scan to USB
• PictBridge printing
• Printing (both color and black-and-white)
• Color printing
• Sending faxes via LAN-Fax
Restricting Machine Functions According to User
125
For each user, you can specify which functions are available upon authentication. A maximum of 30
users can be registered.
users can be registered.
1.
Start the Web browser, and access the machine by entering its IP address.
2.
Click [Restrict Available Functions].
3.
Enter the administrator password if required.
4.
Click [Apply].
5.
Under "Available Functions", select [Restrict] for the functions you want to restrict, and
then click [Apply].
then click [Apply].
Select [Do not Restrict] for the functions you do not want to restrict.
The user restriction setting is enabled for the selected function. Proceed to the following steps to
register users.
The user restriction setting is enabled for the selected function. Proceed to the following steps to
register users.
6.
Click [Available Functions per User].
A list of currently registered user entries appears.
2. Getting Started
126