DOWNLOAD Sharp DX-C202 Service Manual ↓ Size: 7.05 MB | Pages: 127 in PDF or view online for FREE

6.

Lift and slide the tray, then push it all the way in.

CER074

To avoid paper jams, make sure the tray is securely inserted.

• The upper limit differs depending on paper type; thin paper or thick paper. Check the engraved

line inside the tray to confirm the upper limit.

• The remaining paper indicator on the right front side of the paper tray shows approximately how

much paper is remaining.

• For details about paper types supported by the machine, see p.82 "Paper and Other Media".
• For details about the paper settings, see p.114 "Specifying Paper Type and Paper Size".

Loading Paper in the Bypass Tray

• Before printing on paper other than envelopes, make sure that the fusing unit levers inside the front

cover are pulled up. Leaving the levers lowered can cause print quality problems when printing on
paper other than envelopes.

• Set the size of the loaded paper using the control panel or the printer driver. Make sure the settings

do not conflict. Otherwise, the paper may jam or the print quality may be affected.

• Load paper with the print side down and in the short-edge feed direction.
• Duplex printing is not possible.
• You cannot use the bypass tray to feed in paper that requires a specified printing position (such as

preprinted paper). Use tray 1 for such paper.

• If paper is curled, straighten it before loading, by bending the paper in the opposite direction to the

curl, for example.

• Do not load paper while the machine is printing.
• Tray 1 and 2 are unavailable while paper is being loaded in the bypass tray.

Loading Paper

107

• You cannot load paper into the bypass tray while the machine is in Energy Saver mode. If the

machine is in Energy Saver mode, press the [Copy] key to recover from Energy Saver mode.

1.

Insert the top edge of the paper into the machine.

CES134

2.

Adjust the paper guides to the paper size.

CES135

3.

Support the paper with both hands, and insert it carefully until it stops.

CES136

After the paper is inserted until it stops, the paper will be automatically fed into the machine a little.

• After loading paper in the tray, specify the paper type and size using the control panel or the

printer driver.

2. Getting Started

108

• For details about supported types of paper, see p.82 "Paper and Other Media".
• For details about specifying the paper type and size, see p.114 "Specifying Paper Type and

Loading Envelopes

• The inside of this machine becomes very hot. Do not touch the parts labeled " " (indicating a

hot surface).

• Before printing on envelopes, make sure to lower the fusing unit levers inside the front cover to

avoid envelopes coming out creased. Also, pull up the levers back to their original positions after
printing. Leaving the levers lowered can cause print quality problems when printing on paper other
than envelopes.

• Since the temperature around the guide is high, wait for it to cool before touching the fusing unit

levers.

Lowering the fusing unit levers

1.

Pull the opening lever on the front cover, and then carefully lower the front cover.

CES141

Loading Paper

109

2.

Lower the fusing unit levers.

CES257

3.

Using both hands, carefully push up the front cover until it closes.

CES142

Loading envelopes in tray 1

• Avoid using self-adhesive envelopes. They may cause machine malfunctions.
• Check there is no air in the envelopes before loading.
• Load only one size and type of envelope at a time.
• Before loading envelopes, flatten their leading edges (the edge going into the machine) by running

a pencil or ruler across them.

• Some kinds of envelope might cause misfeeds, wrinkles or print poorly.
• Print quality on envelopes may be uneven if parts of an envelope have different thicknesses. Print

one or two envelopes to check print quality.

• In a hot and humid environment, the envelope might be output creased or improper printing

quality.

2. Getting Started

110