Sharp AR-M550 (serv.man23) Service Manual ▷ View online
AR-M550/M620 INSTALLATION MANUAL (AR-FX8) 10 - 1
[10] AR-FX8/AR-MM9 INSTALLATION
<Before installation>
• For installation of AR-FX8, the MFP control PWB unit must have
been installed.
• Start installation after checking that the LINE indicator and the DATA
indicator below it on the operation panel are neither lit nor blinking.
1) Turn off the power switch of the main unit.
<1>Turn the power switch located on the right side of the main unit to
the "OFF" position.
<2>Open the front cabinet and turn the main power switch to the
"OFF" position.
<3>Remove the power plug of the main unit from the outlet.
2) Remove the MFP control PWB.
<1>Remove the two screws that secure the upper right cabinet and
remove the upper right cabinet.
<2>Remove the four screws that secure the MFP control PWB unit to
the main unit.
<3>Raise the two grips and hold them to pull out the MFP control PWB
unit until the stopper is engaged.
<4>Remove the two flat cable connectors.
<5>While using your finger to release the stopper, pull the MFP control
PWB unit out of the main unit.
<Step for mounting extended memory (AR-MM9)>
*
If you need not mount an extended memory, proceed to step 4).
3) Mount an extended memory.
Mount an extended memory to the socket located on the back of
the FAX interface PWB unit.
4) Attach the FAX interface PWB unit.
Connect the FAX interface PWB unit to the FAX interface PWB
connector (100 pin) on the MFP control PWB unit and secure it
connector (100 pin) on the MFP control PWB unit and secure it
with two screws J.
5) Connect the FAX interface cable.
Connect the FAX interface cable to the MFP control PWB unit.
<Caution>
Ensure that both ends of the connector are securely locked and the
connector is not inserted at an angle.
connector is not inserted at an angle.
Parts included
FAX interface PWB unit
(1 pc.)
FAX interface cable
(1 pc.)
Line cable
(1 pc.)
Screw J (small)
(2 pcs.)
1
2
Screws
Upper right
cabinet
2
2
3
3
4
5
5
2
1
Extended memory
FAX interface PWB unit
FAX interface PWB unit
Screws J
AR-M550/M620 INSTALLATION MANUAL (AR-FX8) 10 - 2
6) Reattach the MFP control PWB unit.
<1>Reattach the MFP control PWB to the main unit.
<1>Reattach the MFP control PWB to the main unit.
<2>Connect the two flat cable connectors that have been removed in
step 2).
<Caution>
Ensure that both ends of the connector are securely locked and the
connector is not inserted at an angle.
<3>Secure the unit with four screws.
<4>Return the grips to their original positions.
7) Reattach the upper right cabinet.
Secure the snap band of the FAX interface cable.
Then, remove the cut-out portion for cable arrangement from the
upper right cabinet that has been removed in step 2).
Pull out the grip of the main unit, pass it through the hole shown in
the illustration, then attach the upper right cabinet to the main unit,
and secure it with the two screws.
8) Attach the FAX box unit.
Among the four screws shown in the illustration that secure the
rear cabinet, remove the lower two screws and loosen the upper
two screws.
Then, hang the FAX box unit on the two loosened screws and
Then, hang the FAX box unit on the two loosened screws and
secure it with the two removed screws.
Finally, tighten the two loosened upper screws to secure the FAX
box unit.
box unit.
9) Connect the FAX power connector.
Remove the screw that secures the connector cover on the main
unit for connection with the FAX power connector.
unit for connection with the FAX power connector.
Then, connect the FAX power connector to the connector on the
main unit and tighten the three screws on the connector to secure
the connector.
the connector.
10) Connect the FAX interface cable to the FAX box unit.
Pass the FAX interface cable behind the FAX box unit and connect
it to the FAX box unit.
2
3
3
4
4
1
Screws
Grip
Upper right cabinet
Snap band
Cut-out portion
Screws
Screws
Connector cover
Screw
Screw
FAX power connector
FAX interface cable
AR-M550/M620 INSTALLATION MANUAL (AR-FX8) 10 - 3
11) Turn on the main power switch and the power switch of the main
unit.
<1>Insert the power plug of the main unit to the outlet.
<2>Turn on the main power switch.
Then, close the front cabinet.
<3>Turn on the power switch located on the right side of the main unit.
12) Set the destination of the main unit.
*
*
Be sure to set the destination of the main unit before setting the
destination of the FAX.
<1>Switch the operation panel to the copy mode and use the key
operation [P], [*], [C], and [*] to enter the simulation mode.
<2>Use the 10-key pad to enter "26" in the main code entry screen
shown below and press the START key.
<3>Use the 10-key pad to enter "6" in the sub-code entry screen
shown below and press the START key.
<4>Use the 10-key pad to enter the number of the desired destination
in the submenu screen shown below and press the START key.
(For example, to set the UK as the destination, enter "7" and press
the START key.)
*
When the START key is pressed, the machine will be automatically
rebooted and will start with the setting of the selected destination.
13) Set the destination of the FAX.
<1>Switch the operation panel to the copy mode and use the key
<1>Switch the operation panel to the copy mode and use the key
operation [P], [*], [C], and [*] to enter the simulation mode.
<2>Use the 10-key pad to enter "66" in the main code entry screen
shown below and press the START key.
<3>Use the 10-key pad to enter "2" in the sub-code entry screen
shown below and press the START key.
<4>Select the number of the desired destination referring to
COUNTRY CODE TABLE, use the 10-key pad to enter the number
in the submenu screen shown below and press the START key.
(For example, to set the UK as the destination, enter "10110100"
and press the START key.)
and press the START key.)
<5>Check the destination in the screen shown below. If the display is
correct, use the 10-key pad to enter "1"(YES) and press the
START key.
<6>Press the CA key.
*
*
The machine is automatically rebooted and starts with the setting
of the selected FAX destination.
COUNTRY CODE TABLE
2
3
Destination
FAX Software SW No.1 - 8
U.S.A
1
0
1
1
0
1
0
1
AUSTRALIA
0
0
0
0
1
0
0
1
NEWZEALAND
0
1
1
1
1
1
1
0
U.K.
1
0
1
1
0
1
0
0
FRANCE
0
0
1
1
1
1
0
1
GERMANY
0
0
0
0
0
1
0
0
SWEDEN
1
0
1
0
0
1
0
1
AR-M550/M620 INSTALLATION MANUAL (AR-FX8) 10 - 4
14) Clear the image memory.
*
*
If an extended memory (AR-MM9) has been mounted in step 3),
be sure to carry out this step.
If no extended memory has been mounted, this step is not
necessary.
necessary.
<1>Switch the operation panel to the copy mode and use the key
operation [P], [*], [C], and [*] to enter the simulation mode.
<2>Use the 10-key pad to enter "66" in the main code entry screen
shown below and press the START key.
<3>Use the 10-key pad to enter "10" in the sub-code entry screen
shown below and press the START key.
<4>Use the 10-key pad to enter "1" in the submenu screen shown
below and press the START key.
<5>The screen shown below is displayed and memory clear operation
is executed.
<6>After several minutes, memory clear operation is completed and
then the main unit is rebooted automatically.
15) Connect the line cable to the FAX box unit.
Connect the line cable to the FAX box unit.
Line cable
Click on the first or last page to see other AR-M550 (serv.man23) service manuals if exist.