Sharp AR-M550 (serv.man23) Service Manual ▷ View online
AR-M550/M620 INSTALLATION MANUAL (AR-CF2) 3 - 8
3) Loosen the fixing screws (2 pcs.) of the adjustment section of the
base.
4) Use the spanner removed in step 1) to adjust the height adjustment
bolt so that the upper cabinet is of the same height.
5) Tighten the adjustment section fixing screws (2 pcs.).
6) Close the finisher front door lower, and close the inserter front door.
B. Adjust the rear side height.
1) Remove two screws which are fixing the base cover attached to the
finisher rear side base section, and remove the base cover.
2) Loosen the adjustment section fixing screws (2 pcs.).
3) Use the spanner and adjust the height adjustment bolt so that the
height of the rear side cabinet top surface is of the same height.
4) Tighten the adjustment section fixing screws (2 pcs.).
5) Install the base cover.
(13) Check the clearance between the main unit and the
inserter
1) Push the inserter into the main unit.
2) Check the upper and the lower clearances between the main unit
and the inserter cabinet.
: Jan. 9 2004
1
AR-M550/M620 INSTALLATION MANUAL (AR-CF2) 3 - 9
• When the upper and the lower clearances differ:
1) Open the front upper door of the finisher, and remove the spanner
(fixed with a screw) from the inside of the door.
2) Remove the base cover (fixed with a screw in the front and a screw
at the back) fixed to the front and the rear of the finisher base sec-
tion.
tion.
3) Loosen the front side and the rear side adjustment section fixing
screws (2 pcs. for each side).
4) Turn the front and the rear side adjustment bolts with the spanner
removed in step 1) so that the upper and the lower clearances are
the same.
the same.
5) Check that the upper and the lower clearances are even when
viewed from the front and the back.
6) Tighten the front and the rear side adjustment section fixing screws
(2 pcs. for each side).
7) Install the base cover (front and rear).
8) Return the spanner to the original position.
(14) Install the plate
∗
At that time, check to insure that the upper and lower positioning
tabs are in the plate holes.
tabs are in the plate holes.
Remark: The plate and the connection plate are common to the fin-
isher. Please reuse rail and connector plate for inserter.
1) Hang the plate on the rear lower side of the inserter as shown in the
figure, and fix it with the fixing screw G (1 pc).
1
AR-M550/M620 INSTALLATION MANUAL (AR-CF2) 3 - 10
(15) Turn ON the main power switch
1) Insert the power plug of the main unit to the outlet.
2) Open the front cabinet, and open the power cover.
3) Turn ON the main power switch, close the power cover, and close
the front cabinet.
4) Turn ON the power switch on the right side of the main unit.
AR-M550/M620 INSTALLATION MANUAL (AR-F15/F16) 4 - 1
[4] AR-F15/F16 UNPACKING AND
INSTALLATION
1. Unpacking
When removing or moving, be sure to perform by two persons not to
drop the unit.
drop the unit.
A. Unpacking procedure
(1) Removal of the main unit
1) Remove the fixing member and remove the top case.
2) Remove the packaged parts from the add.
3) Check the packaged parts.
Packaged parts
4) Hold the upper section of the machine with two persons, and pull it
up and stand it straight.
(The machine is very heavy. Be careful.)
5) Remove the tape and the skid.
6) Remove the upper add.
1
Positioning pin
1 pc.
5
Staple label
2 pcs.
2
Earth plate
1 pc.
6
Screw G (M4 x 6)
3 pcs.
3
Earth mounting plate
1 pc.
7
Screw H (M4 x 10)
2 pcs.
4
Rail mounting plate
1 pc.
8
Screw I (M4 x 18)
4 pcs.
1
2
5
6
3
4
8
7
Click on the first or last page to see other AR-M550 (serv.man23) service manuals if exist.