AR-M550 (serv.man23). ARM550 620 Installation Manual — Sharp Copying Equipment Service Manual (repair manual)

Model
AR-M550 (serv.man23)
Pages
56
Size
7.48 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / ARM550 620 Installation Manual
File
ar-m550-sm23.pdf
Date

View Sharp AR-M550 (serv.man23) Service Manual online

CONTENTS
Parts marked with “
” are important for maintaining the safety of the machine. Be sure to replace these parts
with the replacement parts specified to maintain the safety and performance of the machine.
SHARP CORPORATION
INSTALLATION MANUAL
CODE : 00ZAR625//I2E
DIGITAL LASER COPIER/PRINTER
DIGITAL MULTIFUNCTIONAL SYSTEM
AR-M550N/M550U
MODEL
AR-M620N/M620U
[ 1 ]  AR-M550/M620 UNPACKING AND INSTALLATION  . . . . . . . . . . 1 - 1
[ 2 ]  AR-LC6 UNPACKING AND INSTALLATION  . . . . . . . . . . . . . . . . 2 - 1
[ 3 ]  AR-CF2 UNPACKING AND INSTALLATION  . . . . . . . . . . . . . . . . 3 - 1
[ 4 ]  AR-F15/F16 UNPACKING AND INSTALLATION . . . . . . . . . . . . . 4 - 1
[ 5 ]  AR-PN4 UNPACKING AND INSTALLATION  . . . . . . . . . . . . . . . . 5 - 1
[ 6 ] AR-P19 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
[ 7 ] AR-FR11 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
[ 8 ] AR-PK5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
[ 9 ] AR-NS3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
[10]  AR-FX8/AR-MM9 INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
1
1
1
1
AR-M550/M620  INSTALLATION MANUAL  (AR-M550/M620)  1 - 1
[1] AR-M550/M620 UNPACKING AND 
INSTALLATION
1. Installing (use) conditions
Before installing the machine, check that the following installing (use)
conditions are satisfied.
If the installing (use) conditions are not satisfied, the machine may not
display full performances, resulting in troubles. It may also cause
safety problems. Therefore, be sure to arrange the installing (use) con-
ditions before setting up the machine.
A. Bringing space
For installation of a large size machine, be sure to check that the door
size is great enough before bringing in.
B. Installing space
The following space must be provided around the machine in order to
assure machine performances and proper operations.
If any option is installed, provide the additional space for installing it.
Especially the space at the rear of the machine must be provided suffi-
ciently. If not, the machine cannot exhibit functions against heat and
dust, causing some troubles.
C. Power source 
(Capacity, voltage, frequency, safety, plug)
If the power specifications are not satisfied, the machine cannot exhibit
full performances and may cause safety trouble.
Strictly observe the following specifications.
(1) Power capacity
Check that the following power capacity is satisfied. If not, additionally
provide a power source.
Current capacity
Japan: 20A or more
100V: 20A or more
200V: 10A or more
(2) Power voltage
Measure the voltage during copying to check that the voltage is in the
range of the specified voltage ±10%.
If the voltage is outside the specified range, use thicker lead wires to
reduce impedance.
(An electrical work is required.)
Use of a step-up transformer is also available. In this case, the capac-
ity must be great enough for the max. power consumption of the
machine.
(3) Power frequency, waveform
The frequency must be within the range of the specified frequency
±2%. If power waveform is deformed, a trouble may occur.
(4) Safety
Be sure to properly ground the machine.
(5) Power plug
Check the form of the power plug. If the shape does not match, do not
use it.
D. Floor strength and level
This machine is considerably heavy and becomes heavier with an
option installed.
The floor must be strong enough for assuring safety, and the machine
must be installed horizontally.
If not, toner concentration control is not properly performed, resulting in
degraded copy quality and distorted images.
E. Direct rays of the sun, dust, temperature, 
humidity, gasses, chemicals, vibration
(1) Temperature and humidity
This machine is designed to perform properly under the specified tem-
perature and humidity. If the temperature and humidity exceeds the
specified range, the machine may not operate properly and or cause
equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
(Do not install the machine near a stove, a humidifier, or an air condi-
tioner.)
Do not install the machine near a heater, a cooler, or a humidifier.
Dew may be formed inside the machine to cause a trouble. Use
enough care for ventilation.
No.
Content
1
Bringing space
2
Installing space
3
Power source (Capacity, fluctuation, safety)
4
Floor strength
5
Direct rays of the sun, dust, temperature, humidity, gases, 
chemicals
31.5"
(80cm)
23.6"
(60cm)
23.6"
(60cm)
11.8"
(30cm)
Humidity (RH)
85%
60%
20%
10˚C
30˚C 35˚C Temperature
AR-M550/M620  INSTALLATION MANUAL  (AR-M550/M620)  1 - 2
(2) Dust
If dust enters the machine, it may cause dirty copy and a paper jam,
resulting in a shortened lifetime.
(3) Direct rays of the sun
If the machine is installed under the rays of the sun, the exterior of the
machine may be discolored and abnormal copies may be produced.
(4) Gases and chemicals
Do not install the machine at a place where there are gases and chem-
icals. Especially be careful to avoid installation near a diazo-type
copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, manpower of four or more persons is required.
The machine is considerably heavy, and requires safety precautions
for delivery and installation.
Transit of the machine must be made in packed condition to the install-
ing place.
B. Delivery
Remove the packing materials prior to installation in the ofice environ-
ment.
3. Unpacking
A. Unpacking procedure
1) Remove the PP band.
2) Remove the top case.
3) Remove the internal packing pads and the items packed together
with the machine.
No.
Content
Method
1
Implements, facility, 
and manpower
Use a forklift. (If no forklift is available, 
manpower of four or more persons is 
required.)
2
Delivery
Transit must be made in packed 
condition.
1
PP band
7
Polyethylene bag
2
Top case
8
Bottom case unit
3
Pack case
9
Accessory unit
4
Skid pad
10
Paper exit tray AS
5
Top pad R
11
Operation manual
6
Top pad L
AR-M550/M620  INSTALLATION MANUAL  (AR-M550/M620)  1 - 3
4) Remove the adjuster cover and the screw (in the bag).
5) Cut the four corners of the bottom case.
6) Lift the machine slightly, and remove the bottom pad L.
7) Lift the machine slightly, and remove the bottom pad R.
8) Remove the slope.
Slope: Parts
9) Attach the slope to the concave section of the skid.
10) Hold the machine grips and push them down in the arrow direc-
tion.
Part name
Part code
Skid slope
DKiT-0367FCZZ
AR-M550/M620  INSTALLATION MANUAL  (AR-M550/M620)  1 - 4
B. Adjuster cover installation
1) Move the main unit to the installing position, and turn the adjuster to
fix the main unit.
2) Remove the bottom tray from the main unit.
3) Install the adjuster cover to the main unit.
4)
Insert the bottom tray into the main unit.
Note: This machine includes a hard disk drive, which must be pro-
tected against vibrations and shocks.
Never move the machine with the power ON.
Packed items
C. Remove the fixing tape and the reinforcing 
material
1
Driver (CD-ROM)
x 1
2
Operation manual
x 1
3
Delivery and installation report
x 1
4
Paper exit tray
x 1
1
2
3
4

Download Sharp AR-M550 (serv.man23) Service Manual (Repair Manual)

Here you can view online or download Sharp AR-M550 (serv.man23) Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Sharp AR-M550 (serv.man23) Copying Equipment. Information contained in Sharp AR-M550 (serv.man23) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).