Sharp AR-M550 (serv.man23) Service Manual ▷ View online
AR-M550/M620 INSTALLATION MANUAL (AR-F15/F16) 4 - 2
7) One person holds the machine so that it does not fall down. The
other person tilts the machine a little to remove packing material.
8) Bring the base of the unit into contact with the floor so that it does
not fall down.
(The base section is slippery. Be careful of that.)
9)
Tilt the machine to the opposite side a little, and remove packing
material on the opposite side.
material on the opposite side.
10) Slowly bring the base section of the machine on the opposite side
to contact with the floor.
11) Remove the vinyl cover.
(2) Fixing member removal
Remove the taping from the finisher.
Remove the shipment locking material with red sticky note.
1) Remove the tape.
2) Remove the tape and remove the protection board and the sheet.
3) Remove the tape and open the upper cover.
4) Remove the tape and remove the transit fixing member and the
sheet.
5) Remove the tape and remove the lower tray transit fixing member.
1
1
2
1
2
1
AR-M550/M620 INSTALLATION MANUAL (AR-F15/F16) 4 - 3
6) Remove the tape and the fixing member.
7) Remove the tape and remove the jam release door transit fixing
member.
8) Remove the tape and remove the jam release door handle section
transit fixing member.
9) Remove the power cable fixing tape.
10) Open the upper front door, and remove the staple transit fixing
member.
11) Open the lower door, and remove the each tape.
12) Pull out the stitcher remove the screw, and remove the stitcher
transmit fixing member.
13) Remove the screw, and remove the lower cover.
14) Remove the screw, and remove the transit fixing members F and
R.
15) Remove the screw, and remove lift tray rail section transit fixing
members (4 positions).
1
2
3
1
2
1
2
2
2
1
2
2
: Jan. 9 2004
1
AR-M550/M620 INSTALLATION MANUAL (AR-F15/F16) 4 - 4
B. Note for packing
(1) Finisher transit fixing member installation
1) Remove the rear cabinet of the finisher.
2) Turn on the power of the main unit.
3) Raise the DIP switch 1, 2, 4, 5, and 6 on the rear of the finisher.
4) Press SW1 button (left side) of the PWB. (It is located over the DIP
switch.)
∗
The finisher tray moves to the screw fixing position.
5) Turn off the power of the main unit.
6) Reset the DIP switch to the original state.
7) Install the cabinet.
8) Install the lift tray rail section fixing members (4 positions) with four
screws.
2. Installation
A. Installation procedure
(1) Turn off the power of the main unit.
1) Turn OFF the power switch on the right side of the main unit.
2) Open the front cabinet, and turn OFF the main power switch.
3) Disconnect the power plug from the power outlet.
(2) Attach the positioning pin and the earth plate to the
main unit.
When unpacking
Before packing (Shifted to
the screw fixing position.)
the screw fixing position.)
1) Attach the positioning pin with two fixing screws I to the left upper
section of the main unit. Be careful to the attachment direction of
the positioning pin.
the positioning pin.
1
AR-M550/M620 INSTALLATION MANUAL (AR-F15/F16) 4 - 5
2) Attach the earth plate with the fixing screws H (2 pcs.) to the left
lower section of the main unit.
In this case, attach so that the R mark on the earth plate faces up.
3) Pull out the lock release lever on the left side of the main unit, and
open the left door.
4) Remove the paper exit cover on the upper side of the left door.
5) Close the left door.
6) Install the connection plate to the main unit with the fixing screws I
(2 pcs.).
(3) Plate and connection plate installation
1) Install the plate to the finisher as shown in the figure, and fix it with
the fixing screw G (1 pc).
2) Install the rail and the finisher with two screws G (M4 x 6).
(4) Caster adjustment
A. Bring the finisher closer to the main unit and check that the
guide pin of the main unit enters into the connection hole in the
finisher smoothly.
finisher smoothly.
B. At that time, check that the center of the guide pin is in the cen-
ter of the scale marked on the side of the connection hole, and
the pin direction coincides with the hole direction.
the pin direction coincides with the hole direction.
C. If the guide pin is not in the center, or if the guide pin does not
enter smoothly, adjust as follows:
F
R
2
1
Click on the first or last page to see other AR-M550 (serv.man23) service manuals if exist.