DOWNLOAD Sharp AR-M550 (serv.man23) Service Manual ↓ Size: 7.48 MB | Pages: 56 in PDF or view online for FREE

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 4

7) Attach the connecting plate to the with fixing screws I (2 pcs.) main

unit.

1) Remove the step screw (1 pc) and the screws (2 pcs.) which are fix-

ing the punch cover.

2) Fit the holds of the screws removed in step 1) with the screw holes

of the positioning plate, and fix it with the three fixing screws C.

1) Open the front door of the inserter, and loosen the lock fixing screw

until the screw is released.

2) Stand the tray.

3) Install the button cover with the lock button fixing screws D (2 pcs.)

to hide the lock button on the top of the punch cover.

Use positions

1) Open the front door of the inserter, and install the upper limit regula-

tion wire with the two fixing screws E.

1

2

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 5

3) Hold the lower section of the front cabinet and the grip of the rear

cabinet as shown in the figure, tilt the inserter a little so that the indi-
cation hole in the inserter support section is fit with the metal fixture
of the finisher connecting plate installing section, and install it.

∗

At that time,  check that the finisher lock lever is engaged on the
inserter groove securely.

4) Tighten the fixing screw of the inserter lock to fix the inserter and

the finisher.

5) Check that the finisher lock lever is engaged on the inserter groove

securely.

When the finisher and the inserter differ in the height, perform the fol-
lowing height adjustment, and insert the inserter.

1) Set all the finisher height adjustment screws (4 positions) to the

center positions.

2) Insert the inserter to the finisher. (Refer to the procedure (7) in this

section.)

1) Pull out the extension guide of the inserter paper feed tray until it

stops.

2) Tighten the fixing screws F (2 pcs.) on the back side of the paper

feed tray.

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 6

Remark: The plate and the connection plate are common to the fin-

isher. Please reuse rail and connector plate for inserter.

1) Connect the finisher relay harness connector to the inserter con-

nector, and tighten the connector screw to fix it.

2) Fix the finisher relay harness to the rear side of the inserter with two

clamps.

3) Connect the inserter relay harness connector to the main unit con-

nector, and tighten the connector screw to fix the connector.

1) Bring the inserter closer to the main unit.

2) Check that the main unit positioning pin enters smoothly into the

center of the inserter positioning guide.

1) Install the connection plate to the inserter with the fixing screws G

(2 pieces.).

1

2

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 7

1) Loosen the adjustment section fixing screws (2 pcs.) on the rear

side.

2) Turn and adjust the rear side height adjustment bolt so that the cen-

ter height of the positioning pin comes at the center of the position-
ing guide.

3) Tighten two fixing screws of the rear side adjustment section.

4) Loosen the front side adjustment section fixing screws (2 pcs.)

5) Turn and adjust the front side height adjustment bolt so that it is at

the same position with the rear side adjustment section fixing
screw.

6) Tighten two fixing screws of the front side adjustment section.

1) Check the height of the inserter front cabinet and the finisher front

cabinet.

2) Check the height of the inserter rear cabinet and the finisher rear

cabinet.

Go to procedure 13.

A. Adjust the height of the front side.

1) Open the finisher front door upper, remove the spanner stored in

the upper section of the front door, and close the front door upper.

2) Open the front door of the inserter, open the front door lower of the

finisher

F

R