DOWNLOAD Sharp AR-M550 (serv.man23) Service Manual ↓ Size: 7.48 MB | Pages: 56 in PDF or view online for FREE

AR-M550/M620  INSTALLATION MANUAL  (AR-PN4)  5 - 3

1) Attach the rear cabinet B to the original position, and fit it with the

fixing screws (2 pcs.).

2) Open the front door of the punch cover, attach the punch cover to

the original position, and fix it with the fixing screws (6 pcs.).

In this case, use the fixing screws at their original positions.

Memo: Open the lower cover before hand. This makes assembly eas-

ier.

1) Attach the punch position label as shown in the figure.

∗

The label attachment position shown above is based on the corner
of the cabinet.

1) Remove the connector cover fixing screw for connection of the fin-

isher joint harness connector, and remove the connector cover.

2) Connect the finisher joint harness connector to the main unit con-

nector, and tighten the screw on the connector to fix.

1) Insert the power plug into the power outlet.

0.5mm

40mm

40mm

2mm

2mm

AR-M550/M620  INSTALLATION MANUAL  (AR-PN4)  5 - 4

2) Open the front cabinet, and open the power cover.

3) Turn ON the main power switch, close the power cover, and close

the front cabinet.

4) Turn ON the power switch on the right side of the main unit.

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-P19)  6 - 1

To enable the printer expansion function, the product key must be
acquired.

1) Turn the power switch located on the right side of the main unit to

the "OFF" position.

2) Open the front cabinet and turn the main power switch to the

"OFF" position.

3) Remove the power plug of the main unit from the outlet.

1) Remove the two screws that secure the upper right cabinet and

remove the upper right cabinet.

∗

If cables are connected to the control PWB, remove all cables.

2) Remove the four screws that secure the control PWB unit to the

main unit.

3) Raise the two grips and hold them to pull out the control PWB unit

until the stopper is engaged.

4) Remove the two flat cable connectors.

5) While using your finger to release the stopper, pull the control PWB

unit out of the main unit.

1) Remove the ROMs (MAIN and BOOT ROMs) from the control

PWB and replace them with the two ROMs (MAIN and BOOT
ROMs) of the printer expansion kit.

The MAIN and BOOT ROMs are indicated with "MAIN" and
"BOOT" on the labels on the ROMs respectively.

When mounting the printer expansion kit ROMs, insert them to the
same positions in the same orientations as those before replace-
ment until they click and ensure that the inserted ROMs are locked
with the sockets.

2) Remove the screws that secure the cover and remove the cover.

Then, insert the connector of the print server card to the connector
of the control PWB.

3) Secure the print server card using the screws that have been

removed.

MAIN ROM: 1 pc.

·

 Printer utility CD-ROM: 1 pc.

·

 Network utility CD-ROM: 1 pc.

·

 Product key sheet: 1 sheet

Print server card: 1 pc.

BOOT ROM: 1 pc.

Screws

Upper right cabinet

 MAIN ROM

Notches

BOOT ROM

Screws

Cover

Print server card

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-P19)  6 - 2

1) Reattach the control PWB unit to the main unit.

2) Reconnect the two flat cable connectors that have been removed

in step (2).

3) Secure the unit with the four screws.

4) Return the grips to their original positions.

5) Pull out the grip of the main unit, pass it through the hole shown in

the illustration, then reattach the upper right cabinet that has been
removed in step (2) to the main unit, and secure it with the two
screws.

∗

Reconnect the cables that have been removed to the control PWB
located on the side of the main unit.

If another peripheral device must be installed, carry out the following
steps at the end of the installation work.

1) Insert the power plug of the main unit to the outlet.

2) Turn on the main power switch and then close the front cabinet.

3) Turn the main switch located on the right side of the main unit to

the "ON" position.

1) To enable the printer expansion function, use the keys on the oper-

ation panel to enter the product key.

For entry of the product key, see the section of key operator pro-
grams of the operation manual for the main unit.

After completing product key entry, turn off the power switch and
the main power switch of the main unit and then turn on the power
switch and the main power switch of the main unit again.

2) Carry out the network setting for the print server card.

Use the key operator programs to carry out the network setting for
this machine.

For this network setting, the customer's network environment must
be checked. Consult the network administrator to carry out the set-
ting.

3) According to the customer's network environment, install the

printer driver software using the supplied CD-ROM.

Installation of the driver software to the computer server and its
setting must be performed by the customer or based on discussion
with the customer.

When installation of the printer driver is complete, carry out test page
printing to check to see if printing and output can be performed nor-
mally.

(When test printing is complete, use the list print of in custom settings
to print the network settings for this machine and keep the print care-
fully.)

Grip

Screws

Upper right cabinet