DOWNLOAD Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ↓ Size: 7.51 MB | Pages: 112 in PDF or view online for FREE

AR-M350 SIMULATIONS 10-70

<This mode is for development, and inhibited in the market.>

<This mode is for development, and inhibited in the market.>

<This mode is for development, and inhibited in the market.>

<This mode is for development, and inhibited in the market.>

Purpose

Operation test, check

Function (Content)

Used to download the FAX program. 
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure The contents of ROM in the option memory (AR-

MM9) installing section are copied as FAX 
program.

Purpose

Operation test, check

Function (Content)

Used clear the FAST memory data. 
(Only when FAX is installed.)

Section

FAX

Item

Operation 

Operation/Procedure 1) Select with 10 digit key pad, press START to

execute the following.

  1: Fast memory data clear
  2: Not clear

2) After completion of memory clear, 

reset is made.

SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
EJECT PROTECT PIN, AND PRESS START.

SIMULATION 66-24
FAST MEMORY DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO

Purpose

Setup

Function (Content)

Used to register the FAX number for MODEM 
dial-in. (Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure

Purpose

Setup

Function (Content)

Used to register the external telephone number 
for MODEM dial-in. (Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure

Purpose

Setup

Function (Content)

Used to register the voice-warp transfer number. 
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure

SIMULATION 66-25
M-D-IN FAX NUMBER SETTING. 0-9: [0-9],*: [*],#: [#]
INPUT NUMBER AND PRESS START.

0123456789*#01234567

SIMULATION 66-26
M-D-IN EXTEL NUMBER SETTING. 0-9: [0-9],*: [*],#: [#]
INPUT NUMBER AND PRESS START.

0123456789*#01234567

SIMULATION 66-27
V-WP TRANSMIT NUMBER SETTING. 0-9: [0-9],*: [*],#: [#]
INPUT NUMBER AND PRESS START.

0123456789*#01234567

    !" #$%&'

AR-M350 SIMULATIONS 10-71

<This mode is for development, and inhibited in the market.>

<This mode is for development, and inhibited in the market.>

Purpose

Setup

Function (Content)

Used to record a sound message. 
Recording is available in 1 ~ 5, max. 6sec for 
one. (Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure 1) Record a sound message from the handset.

2) Press CUSTOM SETTING to interrupt

recording

Purpose

Setup

Function (Content)

Used to clear the telephone directory. 

Section

FAX

Item

Operation

Operation/Procedure 1) Select with 10 digit key pad and press START

to execute the following.

  1: Telephone directory clear
  2: Telephone directory not clear

SIMULATION 66-28
VOICE RECORD. SELECT 1-5, AND PRESS START.
1. MESSAGE1

2. MESSAGE2

3. MESSAGE3

4. MESSAGE4

5. MESSAGE5

1

SIMULATION 66-29
ADDRESS DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO

1

Purpose

Setup

Function (Content)

Used to check TEL/LIU status change. 
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure The TEL/LIU status can be checked.

The display is highlighted when the status is 
changed. 

HS1

Polarity reverse signal

HS2

Polarity reverse signal

RHS

Handset hook SW

EXHS

External telephone hook SW

Purpose

Setup

Function (Content)

Used to set the TEL/LIU status. 
(Only when FAX is installed.)

Section

Fax

Item

Operation

Operation/Procedure Entry of only 0 or 1 is effective.

Shift the cursor to the bit to enter. 
Cursor shift keys : 

 : * , 

 : #.

The bits are 1, 2, 3, 4, 5, 6, 7, and 8 from the left.
The entered bit is highlighted. 
Press STRT to select the relay.

Purpose

Setup

Function (Content)

Used to check the received data.
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/Procedure The fixed data received from the line are 

checked. 

CHECKING

Checking

OK

Checking complete

NG

Checking end

SIMULATION 66-30
TEL/LIU SENSOR CHECK.
HS1

HS2

EXHS

1

RHS

10001100

SIMULATION 66-31
TEL/LIU SETTING.
INPUT O 1, AND PRESS START.
MOVEMENT LEFT: [*] RIGHT: [#]
1. 

2.CION 

3. MR

4. EC

5. 

6. 

7. DP

8.

1 2 3 4 5 6 7 8

MPXA

S.

CML

SIMULATION 66-32
RECEIVED DATA CHECK.
CHECKING...(OK or NG)

    !" #$%&'

AR-M350 SIMULATIONS 10-72

<This mode is for development, and inhibited in the market.>

Purpose

Setup

Function (Content)

Used to check signal detection. 

Section

FAX

Item

Operation

Operation/Procedure When the signal is detected, the display is 

highlighted.

Purpose

Setup

Function (Content)

Used to measure and display the communication 
time. 

Section

FAX

Item

Operation

Operation/Procedure The time spent for communication is measured. 

Send/receives performed in the normal mode.
The communication time is displayed with the 
simulation. (unit: ms)

Communication means

memory transmission

Image quality

Normal 

Density

Thin

ECM

ON

Sender record

OFF

Purpose

Operation test, check 

Function (Content)

Modem program rewriting.

Section

FAX

Item

Operation

Operation/Procedure The modem program in the FAX program is 

rewritten.
1) Select with 10 digit key pad and press START

to execute the following.

  1: MODEM program rewrite
  2:Not clear

2) Check the check sum value (loader). 

If it is OK, the test is normally completed. 
If NG, the check sum value 
(1 byte = hexadecimal) is displayed. 

3) If the check sum value is NG, the MODEM

result is also NG.

4) The Modem rewrite result is displayed.

SIMULATION 66-33
SIGNAL DETECT CHECK.
BUSY TONE

CNG

CED

FNET

DTM

SIMULATION 66-34
COMMUNICATION TIME DISPLAY.
***** ms

COMPLETE

Writing completed

81

Check sum error

82

Write error

83

Delete error

84

Verify error

NG

Due to loader error

Purpose

Operation test, check

Function (Content)

Used to check interface between MFPC and 
MDMC. Check is made in the data line or the 
command line.

Section

FAX

Item

Operation  

Operation/Procedure 1) Select with 10 digit key pad and press START.

2) When check is "repeat,"  the operation is

executed until the result becomes NG or
CUSTOM SETTING is pressed.

1

MFPC <- MDMC

Data line once only

2

MFPC -> MDMC

Data line once only

3

MFPC <- MDMC

Data line repeat

4

MFPC -> MDMC

Data line repeat

5

MFPC <- MDMC

Command line once only

6

MFPC -> MDMC

Command line once only

7

MFPC <- MDMC

Command line repeat

8

MFPC -> MDMC

Command line repeat

SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE ?
1. YES
2. NO

1

SIMULATION 66-35
MODEM PROGRAM RELOAD. EXECUTING...
LOADER...(OK or Check Sum value 1 byte (hexadecimal))
MODEM...(COMPLETE or NG code 1 byte (Hexadecimal))

SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER...OK
MODEM...COMPLETE

Press [START] key.

After completion of writing

SIMULATION 66-36
MFPC-MDMC I/F CHECK . INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MFPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)

1

1

SIMULATION 66-36
MFPC-MDMC I/F CHECK . INPUT 1-8, AND PRESS START.
EXECUTING...

SIMULATION 66-36
MFPC-MDMC I/F CHECK . INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG)

Press [START] key.

When check is "once" or "repeat"

and the result is NG

When check is "repeat" and
[CUSTOM SETTING] key is pressed.

 +   !" #$%&'

AR-M350 SIMULATIONS 10-73

<This simulation is used only for production, and inhibited in the market.>

Purpose

Operation test, check

Function (Content)

Used to check the parallel I/F operation of the 
printer. 
(This simulation is made only in the production 
site and not in the market. 
It requires a special tool.)

Section

Printer

Item

Operation  

Operation/Procedure The Centro port is checked.

1) Insert the adjustment jig into the Centro port

under the ready state, and press STRT.

2) The Centro port check is started.
3) If normal, OK is displayed. If abnormal, 

the stage number where an error occurred
and NG are displayed. 

WAITING

Waiting

READY

Check start OK

OK

Check complete (normal)

STAGE*NG

Check end (An error occurred in Stage *: 1-11)

Purpose

Adjustment

Function (Content)

Used to set Enable/Disable of the parallel I/F 
select signal of the printer. 

Section

Printer

Item

Operation

Operation/Procedure The select signal of Centro port is set.
Press START to set.

0

OFF

1

ON (Initial value)

SIMULATION 67-2
CENTRO PORT CHECK.
CENTRO PORT:

READY

SIMULATION 67-2
CENTRO PORT CHECK.
CENTRO PORT:

OK

STAGE7 NG

(or

)

Press [CUSTOM SETTING] key.

Press [START] key
under the ready state.

SIMULATION 67-11
CENTRO SELECT IN SIGNAL SETTING. SELECT 0-1, AND PRESS START.
0. OFF
1. ON

0

Purpose

Operation test, check

Function (Content)

Used to check the operation of the network card. 

Section

Printer

Item

Operation  

Operation/Procedure The network card is checked.

CHECKING

Checking

OK

Check complete (Normal)

NG

Check end (Abnormal)

SIMULATION 67-16
NETWORK INTERFACE CARD CHECK.
NIC: CHECKING

SIMULATION 67-16
NETWORK INTERFACE CARD CHECK.
NIC: OK (or NG)

Press [CUSTOM SETTING] key.

Check complete

    !" #$%&'