Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ▷ View online
AR-M350 SIMULATIONS 10-50
<List of set values 1>
<List of display values 1>
<List of set values 2>
<List of set values 3>
50-6
Purpose
Adjustment
Function (Content)
Copy lead edge adjustment (DSPF)
Section
Item
Item
Picture quality
Operation/Procedure Perform the SPF copy lead edge adjustment.
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
Press P to store the set value.
3) Press START to start copying and store the
set value. (Display value: 1)
4) Select a paper feed tray. (Set value 2)
5) Set the scan magnification ratio. (Set value: 3)
5) Set the scan magnification ratio. (Set value: 3)
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS START.
0. TRAY SELECT
LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. SIDE1
3. SIDE1
4. SIDE2
5. IMAGE LOSS(LEAD)SIDE1
6. IMAGE LOSS(SIDE)SIDE1
7. IMAGE LOSS(LEAD)SIDE2
8. IMAGE LOSS(SIDE)SIDE2
9. REAR LOSS SIDE1
6. IMAGE LOSS(SIDE)SIDE1
7. IMAGE LOSS(LEAD)SIDE2
8. IMAGE LOSS(SIDE)SIDE2
9. REAR LOSS SIDE1
10. REAR LOSS SIDE2
2
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS START.
3. SIDE1
LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS START.
3. SIDE1
50
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE+10: DUPLEX MODE)
LEAD EDGE ADJUSTMENT(SPF). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE+10: DUPLEX MODE)
1
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.
LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF).
(MAGNIFICATION)
INPUT 25-200(%)
LEAD EDGE ADJUSTMENT(SPF).
(MAGNIFICATION)
INPUT 25-200(%)
100
20
0
0
100
1
15
20
15
50
50
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
Defauult Set range
0 TRAY SELECT
Paper feed tray selection
-
1 ~ 5
1 COPY START
Copy start (Initial value)
-
-
2 MAGNIFICATION Print magnification ratio
setup (25 - 400%)
-
25 ~ 200
3 SIDE 1
Document front scan start
position adjustment
position adjustment
50
0 ~ 99
4 SIDE 2
Document back scan start
position adjustment
position adjustment
50
0 ~ 99
5 IMAGE LOSS
(LEAD) SIDE 1
Front lead edge image loss
set value
set value
15
0 ~ 99
6 IMAGE LOSS
(SIDE) SIDE 1
Front side image loss set
value
value
20
0 ~ 99
7 IMAGE LOSS
(LEAD) SIDE 2
Back lead edge image loss
set value
set value
15
0 ~ 99
8 IMAGE LOSS
(SIDE) SIDE 2
Back side image loss set
value
value
20
0 ~ 99
9 REAR LOSS
SIDE1
Front rear edge image loss
set value
set value
0
0 ~ 20
10 REAR LOSS
SIDE2
Back rear edge image loss
set value
set value
0
0 ~ 20
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
11
TRAY1 with Duplex
2
TRAY2
12
TRAY2 with Duplex
3
TRAY3
13
TRAY3 with Duplex
4
TRAY4
14
TRAY4 with Duplex
5
Manual feed
15
Manual feed with Duplex
Set range
25 - 200%
* !" #$%&'
AR-M350 SIMULATIONS 10-51
<List of set values 1>
<List of display values 1>
<List of set values 2>
<List of set values 3>
50-7
Purpose
Adjustment
Function (Content)
Copy lead edge adjustment (Simple method)
(DSPF)
(DSPF)
Section
Item
Item
Picture quality
Operation/Procedure Perform the SPF copy lead edge adjustment.
(Simple method)
1) The current set value is highlighted on the
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
Press P to store the set value.
3) Press START to start copying and store the
set value. (Display value: 1)
4) Select a paper feed tray. (Set value 2)
5) Set the scan magnification ratio. (Set value: 3)
5) Set the scan magnification ratio. (Set value: 3)
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS START.
0. TRAY SELECT
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. L4
3. L4
4.L5
5. IMAGE LOSS(LEAD)SIDE1
6. IMAGE LOSS(SIDE)SIDE1
7. IMAGE LOSS(LEAD)SIDE2
8. IMAGE LOSS(SIDE)SIDE2
9. REAR LOSS SIDE1
6. IMAGE LOSS(SIDE)SIDE1
7. IMAGE LOSS(LEAD)SIDE2
8. IMAGE LOSS(SIDE)SIDE2
9. REAR LOSS SIDE1
10. REAR LOSS SIDE2
2
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-999, AND PRESS
START.
3. L4
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-999, AND PRESS
START.
3. L4
50
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE+10: DUPLEX MODE)
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE+10: DUPLEX MODE)
1
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
100
20
200
160
1
15
20
15
50
0
0
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
Defauult Set range
0 TRAY SELECT
Paper feed tray selection
-
1 ~ 5
1 COPY START
Copy start (Initial value)
-
-
2 MAGNIFICATION Print magnification ratio
setup (25 - 400%)
200
25 ~ 200
3 L4
Distance from the front lead
edge of copy image to the
scale of 10mm.
(SPF: 200%)
edge of copy image to the
scale of 10mm.
(SPF: 200%)
-
0 ~ 999
4 L5
Distance from the back lead
edge of copy image to the
scale of 10mm.
(SPF: 200%)
edge of copy image to the
scale of 10mm.
(SPF: 200%)
-
0 ~ 999
5 IMAGE LOSS
(LEAD) SIDE 1
Front lead edge image loss
set value
set value
15
0 ~ 99
6 IMAGE LOSS
(SIDE) SIDE 1
Front side image loss set
value
value
20
0 ~ 99
7 IMAGE LOSS
(LEAD) SIDE 2
Back lead edge image loss
set value
set value
15
0 ~ 99
8 IMAGE LOSS
(SIDE) SIDE 2
Back side image loss set
value
value
20
0 ~ 99
9 REAR LOSS
SIDE1
Front rear edge image loss
set value
set value
0
0 ~ 20
10 REAR LOSS
SIDE2
Back rear edge image loss
set value
set value
0
0 ~ 20
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
11
TRAY1 with Duplex
2
TRAY2
12
TRAY2 with Duplex
3
TRAY3
13
TRAY3 with Duplex
4
TRAY4
14
TRAY4 with Duplex
5
Manual feed
15
Manual feed with Duplex
Set range
25 - 200%
* !" #$%&'
AR-M350 SIMULATIONS 10-52
<List of set values 1>
<List of display values 1>
<List of set values 2>
*
The selected tray is registered as an initial set value in the initial
screen.
At the above value + 10, the SPF enters the duplex mode (DD),
making duplex copies.
making duplex copies.
<List of set values 3>
(Adjustment procedure)
1) Select a paper feed tray to be used in the adjustment,
set the magnification ratio, and enter the adjustment item.
2) After entering the adjustment value, press START, and printing is
started.
3) Check the off-center (distance from the paper edge) of the copy.
Repeat procedure 2) until a satisfactory result is obtained.
Note: When adjusting the off-center of LCC1, set only the left tray of LCC.
When adjusting the off-center of LCC2, set only the right tray of
LCC. This is because there is no distinction between right and left
LCC. This is because there is no distinction between right and left
in selection of a tray.
50-10
Purpose
Adjustment
Function (Content)
Used to adjust the print image center position.
(Adjusted for each paper feed section.)
(Adjusted for each paper feed section.)
Section
Image process (ICU)
Item
Picture quality
Operation/Procedure Perform the print off-center adjustment.
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
Press P to store the set value.
3) When the value of UNIT:0.1mm/STEP is
increased, the image is shifted toward the
rear side.
rear side.
4) Press START to start copying and store the
set value. (Display value: 1)
5) Select a paper feed tray. (Set value 2)
6) Set the scan magnification ratio. (Set value: 3)
6) Set the scan magnification ratio. (Set value: 3)
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-8, AND PRESS START.
0. TRAY SELECT
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-8, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. TRAY1
3. TRAY1
4. TRAY2
5.TRAY3/LCC1
6. TRAY4/LCC2
7. BPT
8.ADU
2
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
3. TRAY1
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
3. TRAY1
50
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE +10: DUPLEX MODE)
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE +10: DUPLEX MODE)
1
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
PRINT OFF-CENTER ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
100
100
1
50
50
50
50
50
50
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
Default Set range
0 TRAY SELECT
Paper feed tray selection
-
1 ~ 5
1 COPY START
Copy start (Initial value)
-
2 MAGNIFICATION Print magnification ratio
setup (25 - 400%)
100
25 ~ 400
3 TRAY 1
Tray 1 adjustment
50
0 ~ 99
4 TRAY2
Tray 2 adjustment
50
0 ~ 99
5 TRAY3
Tray 3 adjustment
50
0 ~ 99
6 TRAY4
Tray 4 adjustment
50
0 ~ 99
7 BPT
Manual feed tray adjustment 50
0 ~ 99
8 ADU
Adjustment in refeed from
ADU
ADU
50
0 ~ 99
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
2
TRAY2
3
TRAY3/LCC1
4
TRAY4/LCC2
5
Manual feed
Set range
25 - 400%
*+ !" #$%&'
AR-M350 SIMULATIONS 10-53
<List of set values 1>
<List of display values 1>
<List of set values 2>
*
The selected tray is registered as an initial set value in the initial
screen.
At the above value + 10, the SPF enters the duplex mode (DD),
At the above value + 10, the SPF enters the duplex mode (DD),
making duplex copies.
<List of set values 3>
(Adjustment procedure)
1) Select a paper feed tray to be used in the adjustment,
set the magnification ratio, and enter the adjustment item.
2) After entering the adjustment value, press START,
and printing is started.
3) Check the off-center (distance from the paper edge) of the copy.
Repeat procedure 2) until a satisfactory result is obtained.
50-12
Purpose
Adjustment
Function (Content)
Used to adjust the reading image center
position. (Adjusted for each document mode.)
position. (Adjusted for each document mode.)
Section
Image process (ICU)
Item
Picture quality
Operation/Procedure Perform the document print off-center
adjustment.
1) The current set value is highlighted on the
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
Press P to store the set value.
3) When the value of UNIT:0.1mm/STEP is
increased, the image is shifted toward the
front side.
front side.
4) Press START to start copying and store the
set value. (Display value: 1)
5) Select a paper feed tray. (Set value 2)
6) Set the scan magnification ratio. (Set value: 3)
6) Set the scan magnification ratio. (Set value: 3)
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-5, AND PRESS START.
0. TRAY SELECT
ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-5, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. PLATEN
3. PLATEN
4. SPF SIDE1
5. SPF SIDE2
2
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
3. PLATEN
ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
3. PLATEN
50
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE +10: DUPLEX MODE)
ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE +10: DUPLEX MODE)
1
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.
ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
ORIGINAL OFF-CENTER ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
100
100
1
50
50
50
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
Default Set range
0 TRAY SELECT
Paper feed tray selection
-
1 ~ 5
1 COPY START
Copy start (Initial value)
-
2 MAGNIFICATION Print magnification ratio
setup (25 - 400%)
100
25 ~ 400
3 PLATEN
OC mode adjustment
50
0 ~ 99
4 SPF SIDE1 SPF
Front surface adjustment
50
0 ~ 99
5 SPF SIDE2 SPF
Back surface adjustment
50
0 ~ 99
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
2
TRAY2
3
TRAY3
4
TRAY4
5
Manual feed
Set range
25 - 400%
* !" #$%&'
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man12) service manuals if exist.