Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ▷ View online
AR-M350 SIMULATIONS 10-66
<List of set values>
<List of set values>
66-11
Purpose
Operation test, check
Function (Content)
Used to check the output operation of FAX G3
mode 300BPS.
(Used to check the MODEM operation.)
Send level 0dB (Max.)
(Only when FAX is installed.)
mode 300BPS.
(Used to check the MODEM operation.)
Send level 0dB (Max.)
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure A signal of 300bps is outputted. (Level Max.)
Enter a number during execution to change the
signal.
Press START to start sending a voice message.
Press CUSTOMSETTING to terminate.
signal.
Press START to start sending a voice message.
Press CUSTOMSETTING to terminate.
1
NO SIGNAL
No signal
2
11111
3
11110
4
00000
5
10101
6
00001
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
1
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
1
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
3
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
3
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
Select 3 and press [START] key.
Select 1 and press [START] key.
Same
display
66-12
Purpose
Setup
Function (Content)
Used to check the output operation of FAX G3
mode 300BPS.
(Used to check the MODEM operation.)
Signals are sent in the send level set with the
soft switch. (Only when FAX is installed.)
mode 300BPS.
(Used to check the MODEM operation.)
Signals are sent in the send level set with the
soft switch. (Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure A signal of 300bps is outputted.
(Send level is set with SW.)
Enter a number during execution to change the
signal.
Press START to start sending a voice message.
Press CUSTOMSETTING to terminate.
Enter a number during execution to change the
signal.
Press START to start sending a voice message.
Press CUSTOMSETTING to terminate.
1
NO SIGNAL
No signal
2
11111
3
11110
4
00000
5
10101
6
00001
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
1
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
1
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING...
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
2
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1.NO SIGNAL 2.11111 3.11110
4.00000
5.010101 6.00001
2
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
Select 3 and press [START] key.
Select 1 and press [START] key.
Same
display
,, !" #$%&'
AR-M350 SIMULATIONS 10-67
<List of set values>
*
Dial is send with the setup value of +29ms.
<List of set values>
*
Dial is set with the setup value of +19ms.
66-13
Purpose
Setup
Function (Content)
Used to select the FAX dial signal output test.
(The dial number signal set with this simulation
is outputted in the dial signal output test with
SIM 66-14~16)
(Only when FAX is installed.)
(The dial number signal set with this simulation
is outputted in the dial signal output test with
SIM 66-14~16)
(Only when FAX is installed.)
Section
FAX
Item
Data
Operation/Procedure The dial test number is set.
Enter a number with 10 digit key pad, * key, and
# key.
The upper limit is 20 digits.
Press CLEAR to return to the initial state.
Press START to register.
# key.
The upper limit is 20 digits.
Press CLEAR to return to the initial state.
Press START to register.
66-14
Purpose
Setup
Function (Content)
Used to set the add time to the FAX pulse dial
mode (10PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
mode (10PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
Section
Fax
Item
Operation
Operation/Procedure The dial test is performed. (10PPS output)
The make time is set.
When CUSTOM SETTING is pressed, the
execution is terminated.
When CUSTOM SETTING is pressed, the
execution is terminated.
0
Execution
1
Dial pulse make time setup (0 - 15)
SIMULATION 66-13
DIAL TEST NUMBER SETTNG.
INPUT NUMBER AND PRESS START.
DIAL TEST NUMBER SETTNG.
INPUT NUMBER AND PRESS START.
0123456789*#01234567
0-9:[0-9], *[*], #:[ ]
1
#
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
DIAL TEST(10PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
1
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
7
7
; [
ms]
+29
SIMULATION 66-14
DIAL TEST(10PPS). EXECUTING...
1.MAKE TIME
DIAL TEST(10PPS). EXECUTING...
1.MAKE TIME
7
; [
ms]
+29
Select 1 and press [START] key. Press [CUSTOM SETTING] key
or [START] key.
Select 0 and
press [START] key.
press [START] key.
Press [CUSTOM SETTING] key.
66-15
Purpose
Setup
Function (Content)
Used to set the add time to the FAX pulse dial
mode (20PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
mode (20PPS) and to test the dial signal output.
(The dial number signal set with SIM 66-13 is
outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
Section
Fax
Item
Operation
Operation/Procedure The dial test is performed. (20PPS output)
The make time is set.
When CUSTOM SETTING is pressed, the
execution is terminated.
When CUSTOM SETTING is pressed, the
execution is terminated.
0
Execution
1
Dial pulse make time setup (0 - 15)
SIMULATION 66-15
DIAL TEST(20PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
DIAL TEST(20PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1.MAKE TIME
1
SIMULATION 66-15
DIAL TEST(20PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
DIAL TEST(20PPS). SELECT 0-15, AND PRESS START.
[1.MAKE TIME]
7
7
; [
ms]
+9
SIMULATION 66-15
DIAL TEST(20PPS). EXECUTING...
1.MAKE TIME
DIAL TEST(20PPS). EXECUTING...
1.MAKE TIME
7
; [
ms]
+9
Select 1 and press [START] key. Press [CUSTOM SETTING] key
or [START] key.
Select 0 and
press [START] key.
press [START] key.
Press [CUSTOM SETTING] key.
, !" #$%&'
AR-M350 SIMULATIONS 10-68
*
For the set value, refer to the soft SW specifications.
<List of set values>
<DTMF signal>
<DTMF signal>
<Set values>
66-16
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
FAX tone dial mode. (The dial number signal set
with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Used to check dialing troubles and the operation.
FAX tone dial mode. (The dial number signal set
with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Used to check dialing troubles and the operation.
Section
FAX
Item
Operation
Operation/Procedure The dial test is performed. (DTMF signal output)
1) The level (dB) setup is made.
(Set range: 0 - 15dB)
2) The difference between high group and low
group is set. (Set range: 0 - 15)
3) When CUSTOM SETTING is pressed,
the execution is terminated.
0
Execution
1
HIGH
High group level
2
HIGH-LOW
High group - low group
66-17
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
Fax tone dial mode. Send level 0db (fixed).
Used to check the dial IC operation.
(Only when FAX is installed.)
Fax tone dial mode. Send level 0db (fixed).
Used to check the dial IC operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The DTMF signal output is checked.
(Output level 0)
When CUSTOM SETTING is pressed,
the execution is terminated.
When CUSTOM SETTING is pressed,
the execution is terminated.
1 - 9, 0, *, #
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.
0. EXECUTE
1.HIGH
DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.
0. EXECUTE
1.HIGH
(dB)
2.
1
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1.HIGH (dB)
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1.HIGH (dB)
7
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
2.
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
2.
7
7
7
HIGH-LOW
7
7
HIGH-LOW
HIGH-LOW
SIMULATION 66-16
DIAL TEST(DTMF). EXECUTING...
1.HIGH
DIAL TEST(DTMF). EXECUTING...
1.HIGH
(dB)
2.
Select 1 or 2 and press [START] key. Press [CUSTOM SETTING] key
or [START] key.
Select 0 and
press [START] key.
press [START] key.
Press [CUSTOM SETTING] key.
(When 1 is selected)
(When 2 is selected)
(When 0 is selected)
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX) INPUT 0 9,* ,#, AND PRESS START.
DTMF SIGNAL OUTPUT.(LEVEL MAX) INPUT 0 9,* ,#, AND PRESS START.
1
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX) EXCUTING...
DTMF SIGNAL OUTPUT.(LEVEL MAX) EXCUTING...
1
Press [START] key.
Press [CUSTOM SETTING] key.
66-18
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
Fax tone dial mode.
The send level set with the soft switch is
outputted.
Used to check the dial IC operation.
(Only when FAX is installed.)
Fax tone dial mode.
The send level set with the soft switch is
outputted.
Used to check the dial IC operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The DTMF signal output is checked.
(Output level is set with soft SW.)
When CUSTOM SETTING is pressed,
the execution is terminated.
When CUSTOM SETTING is pressed,
the execution is terminated.
1 - 9, 0, *, #
66-19
Purpose
Setup
Function (Content)
Used to backup the FAX SRAM data
(Set values of rapid key dialing) into the flash
Memory (AR-MM9).
(When FAX is installed and FAX expansion
memory is installed.)
(Set values of rapid key dialing) into the flash
Memory (AR-MM9).
(When FAX is installed and FAX expansion
memory is installed.)
Section
Fax
Item
Operation
Operation/Procedure The content of SRAM is backed up into Flash
Memory(AR-MM9).
1
Backup executed
2
No backup
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW) INPUT 0
DTMF SIGNAL OUTPUT.(SOFT SW) INPUT 0
9,* ,#, AND PRESS START.
1
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW) EXCUTING...
DTMF SIGNAL OUTPUT.(SOFT SW) EXCUTING...
1
Press [START] key.
Press [CUSTOM SETTING] key.
SIMULATION 66-19
SRAM BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
SRAM BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 66-19
SRAM BACK UP. (WRITE TO FLASH ROM) EXCUTING...
SRAM BACK UP. (WRITE TO FLASH ROM) EXCUTING...
1
Press [START] key.
After completion of backup
,( !" #$%&'
AR-M350 SIMULATIONS 10-69
<Set value>
<List of set values>
<List of set values>
66-20
Purpose
Setup
Function (Content)
Used to restore the backup data (SIM 66-19) to
SRAM. (When FAX is installed and FAX
expansion memory is installed.)
SRAM. (When FAX is installed and FAX
expansion memory is installed.)
Section
Fax
Item
Operation
Operation/Procedure Read/write from Flash Memory(AR-MM9) to
SRAM is performed.
1
Read/Write executed
2
Read/write not executed
66-21
Purpose
Adjustment, setup, operation data output, check
(display, print)
(display, print)
Function (Content)
Used to print the FAX information (registrations,
communication management, file management,
system errors). (Only when FAX is installed.)
communication management, file management,
system errors). (Only when FAX is installed.)
Section
Fax
Item
Data
Operation/Procedure Information related to FAX is printed.
1) Select information to be printed.
2) The selected information is printed.
3) The paper size is automatically selected by
2) The selected information is printed.
3) The paper size is automatically selected by
the size stored in the image memory.
SIMULATION 66-20
SRAM BACK UP. (READ FROM FLASH ROM)
ARE YOU SURE ?
1. YES
2. NO
SRAM BACK UP. (READ FROM FLASH ROM)
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 66-20
SRAM BACK UP. (READ FROM FLASH ROM) EXCUTING...
SRAM BACK UP. (READ FROM FLASH ROM) EXCUTING...
1
Press [START] key.
After completion of reading
0
SIMULATION 66-21
FAX INFORMATION PRINT OUT.EXECUTING...
1. REGISTERED
FAX INFORMATION PRINT OUT.EXECUTING...
1. REGISTERED
SIMULATION 66-21
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1.REGISTERED
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1.REGISTERED
2.MANAGEMENT
3.FILE MANAGEMENT 4.SYSTEM ERROR
5.PROTOCOL
5.PROTOCOL
Select 0 and
press [START] key.
press [START] key.
If there is no data to be printed,
the display returns to the initial state.
the display returns to the initial state.
After completion of printing
1
REGISTERED
Various registered information
2
MANAGEMENT
Communication management information
3
FILE
MANAGEMENT
MANAGEMENT
Fine management information
4
SYSTEM ERROR System error information
5
PROTOCOL
Protocol information
66-22
Purpose
Setup
Function (Content)
Used to adjust the handset sound volume.
(Only when FAX is installed.)
(Only when FAX is installed.)
Section
Fax
Item
Operation
Operation/Procedure The hand set sound volume is set.
1) Press START to set.
2) During execution, selection of 1, 2, and 3 is
2) During execution, selection of 1, 2, and 3 is
possible.
1
Min,
2
Middle
3
Max.
SIMULATION 66-22
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
1.MIN
2.MIDDLE
3.MAX
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
1.MIN
2.MIDDLE
3.MAX
2
SIMULATION 66-22
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
EXECUTING...
1.MIN
2.MIDDLE
3.MAX
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
EXECUTING...
1.MIN
2.MIDDLE
3.MAX
2
SIMULATION 66-22
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
EXECUTING...
1.MIN
2.MIDDLE
3.MAX
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
EXECUTING...
1.MIN
2.MIDDLE
3.MAX
3
SIMULATION 66-22
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
1.MIN
2.MIDDLE
3.MAX
HANDSET VOLUME SETTING. SELECT 1-3, AND PRESS START.
1.MIN
2.MIDDLE
3.MAX
3
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
Select 3 and press [START] key.
Press [START] key.
Same
display
,) !" #$%&'
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man12) service manuals if exist.