Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ▷ View online
AR-M350 SIMULATIONS 10-46
*
The set value is changed only, and printing is not performed.
<Set value>
46-25
Purpose
Adjustment, setup, operation data output, check
(display, print)
(display, print)
Function (Content)
Used to adjust the scanner exposure level and to
make individual setup. (Super fine mode)
make individual setup. (Super fine mode)
Section
Scanner (reading)
Item
Picture quality
Operation/Procedure 1) Select the exposure mode to be set.
(Scanner super fine mode individual
adjustment)
The current set value is highlighted on the
right of each item. (Set value)
adjustment)
The current set value is highlighted on the
right of each item. (Set value)
2) Set the exposure level with 10 digit key pad.
Press P to store the set value.
(Default 50, set range 0 - 99)
(Default 50, set range 0 - 99)
0
Auto
1
Bright
2
Dark
3
Auto (half tone)
4
Bright (Half tone)
5
Dark (Half tone)
SIMULATION 46-25
EXP. LEVEL SETUP SCANNER(ULTRA FINE). SELECT 0-5, AND PRESS
START.
0. AUTO
EXP. LEVEL SETUP SCANNER(ULTRA FINE). SELECT 0-5, AND PRESS
START.
0. AUTO
1. LIGHT
2.DARK
3. AUTO(H)
4. LIGHT(H)
5.DARK(H)
SIMULATION 46-25
EXP. LEVEL SETUP SCANNER(ULTRA FINE), INPUT VALUE 0-99,
EXP. LEVEL SETUP SCANNER(ULTRA FINE), INPUT VALUE 0-99,
AND PRESS START.
0. AUTO
50
1
50
50
50
50
50
50
Press [START] key or
[CUSTOM SETTING] key.
Select 0 -5 and
press [START] key.
press [START] key.
!" #$%&
AR-M350 SIMULATIONS 10-47
<List of set values 1>
<List of display values 1>
<List of set values 2>
*
Above + 10 becomes the duplex mode (DD), making duplex copy.
<List of set values 3>
<List of display values>
Main code 48
48-1
Purpose
Adjustment
Function (Content)
Used to adjust the copy magnification ratio
(main scan direction, sub scan direction).
(main scan direction, sub scan direction).
Section
Scanner (reading)
Item
Picture quality
Operation/Procedure Perform the magnification ratio correction.
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
(Default 50, set range 0 - 99)
Press P to store the set value.
(Default 50, set range 0 - 99)
3) The greater the set value is, the greater the
correction is.
1 step : 0.1% adjustment
1 step : 0.1% adjustment
4) Press START to start copying and store the
set value. (Display value: 1)
5) Select the paper feed tray. (Set value : 2)
6) Set the scan magnification ratio.
6) Set the scan magnification ratio.
(Set value: 3)
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. SELECT 0-9, AND PRESS START.
0. TRAY SELECT
MAGNIFICATION ADJUSTMENT. SELECT 0-9, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. CCD(MAIN)
3. CCD(MAIN)
4. CCD(SUB)
5. SPF(SUB)
6. CIS(MAIN)
2
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START.
3. CCD(MAIN)
MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START.
3. CCD(MAIN)
50
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE +10 : DUPLEX MODE)
MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE +10 : DUPLEX MODE)
1
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. NOW COPYING.
MAGNIFICATION ADJUSTMENT. NOW COPYING.
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
MAGNIFICATION ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
100
50
100
1
50
50
50
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
0
Paper feed tray selection
1
Copy start (Default)
2
Print magnification ratio
3
Main scan magnification ratio (CCD)
4
Sub scan magnification ratio (CCD)
5
SPF surface magnification ratio (sub scan)
6
SPF back magnification ratio (CIS main scan)
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
2
TRAY2
3
TRAY3
4
TRAY4
5
Manual feed
Set range
25 - 400%
48-5
Purpose
Adjustment
Function (Content)
Used to adjust the exposure motor speed.
Section
Scanner (reading)
Item
Picture quality
Operation/Procedure 1) The current set value is displayed on the right
of each item.
2) Set the exposure level with 10 digit key pad.
3) Press START to store the set value.
3) Press START to store the set value.
(Default 50, set range 0 - 99)
0
Mirror motor (220mm/sec)
1
Mirror motor (168.7mm)
2
Mirror motor (110mm/sec)
3
Mirror motor (55mm/sec)
4
SPF motor (220mm/sec)
5
SPF motor (110mm/sec)
SIMULATION 48-5
MOTOR SPEED ADJUSTMENT. SELECT 0-5, AND PRESS START.
0. MIR(220)
MOTOR SPEED ADJUSTMENT. SELECT 0-5, AND PRESS START.
0. MIR(220)
1. MIR(169)
2. MIR(110)
3. MIR(55)
4. SPF(220)
5. SPF(110)
0
SIMULATION 48-5
SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
0. MIR(220)
SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
0. MIR(220)
50
50
50
50
50
50
50
Press [START] key or
[CUSTOM SETTING] key.
Select 0 -5 and
press [START] key.
press [START] key.
!" #$%&'
AR-M350 SIMULATIONS 10-48
<List of set values 1>
<List of display values 1>
<List of set values 2>
<List of set values 3>
Main code 50
50-1
Purpose
Adjustment
Function (Content)
Used to adjust the copy image position and the
void area (image loss) on print paper in the copy
mode. (A similar adjustment can be made with
SIM 50-2 (simple method).)
void area (image loss) on print paper in the copy
mode. (A similar adjustment can be made with
SIM 50-2 (simple method).)
Section
Item
Item
Picture quality
Operation/Procedure Perform the copy lead edge adjustment.
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
Press P to store the set value.
3) Press START to start copying and store the
set value. (Display value: 1)
4) Set the scan magnification ratio. (Set value: 3)
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START.
0. TRAY SELECT
LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. RRCA
3. RRCA
4. RRCB
5. DENB
6. IMAGE LOSS(LEAD)
7. IMAGE LOSS(SIDE)
8. DENA
9. FR_VOID
2
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START.
3. RRCA
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START.
3. RRCA
50
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
LEAD EDGE ADJUSTMENT. SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
1
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. NOW COPYING.
LEAD EDGE ADJUSTMENT. NOW COPYING.
SIMULATION 50-1
LEAD EDGE ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
LEAD EDGE ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
100
15
20
100
1
50
50
50
30
30
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
Default Set range
0 TRAY SELECT
Paper feed tray selection
-
1 ~ 5
1 COPY START
Copy start (Initial value)
-
-
2 MAGNIFICATION
Print magnification ratio
setup
setup
-
25 ~ 400
3 RRCA
Document scan start
position adjustment
position adjustment
50
0 ~ 99
4 RRCB
Resist roller clutch ON
timing adjustment value
timing adjustment value
50
0 ~ 99
5 DENB
Rear edge void quantity
adjustment value
adjustment value
35
0 ~ 99
6 IMAGE
LOSS(LEAD)
Lead edge image loss
quantity set value
quantity set value
15
0 ~ 99
7 IMAGE
LOSS(SIDE)
Side image loss quantity
set value
set value
20
0 ~ 99
8 DENA
Lead edge void quantity set
value
value
35
0 ~ 99
9 FR_VOIDFR
Void quantity adjustment
value
value
35
0 ~ 99
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
2
TRAY2
3
TRAY3
4
TRAY4
5
Manual feed
Set range
25 - 400%
( !" #$%&'
AR-M350 SIMULATIONS 10-49
<List of set values 1>
<List of display values 1>
<List of set values 2>
<List of set values 3>
50-2
Purpose
Adjustment
Function (Content)
Used to adjust the copy image position and the
void area (image loss) on print paper in the copy
mode.
(This simulation is a simpler procedure compared
the similar adjustment using SIM 50-1.)
void area (image loss) on print paper in the copy
mode.
(This simulation is a simpler procedure compared
the similar adjustment using SIM 50-1.)
Section
Item
Item
Picture quality
Operation/Procedure Perform the copy lead edge adjustment.
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
Press P to store the set value.
3) Press START to start copying and store the
set value. (Display value: 1)
4) Set the scan magnification ratio.
(Set value: 3)
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS START.
0. TRAY SELECT
LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS START.
0. TRAY SELECT
1. COPY START
2. MAGNIFICATION
3. L1
3. L1
4. L2
5. IMAGE LOSS(LEAD)
6. IMAGE LOSS(SIDE)
7. DENB
7. DENB
8. DENA
9. FR_VOID
2
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). INPUT VALUE 0-99, AND PRESS START.
3. L1
LEAD EDGE ADJUSTMENT(CALC). INPUT VALUE 0-99, AND PRESS START.
3. L1
50
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
LEAD EDGE ADJUSTMENT(CALC). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
1
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). NOW COPYING.
LEAD EDGE ADJUSTMENT(CALC). NOW COPYING.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC).
(MAGNIFICATION)
INPUT 25-400(%)
LEAD EDGE ADJUSTMENT(CALC).
(MAGNIFICATION)
INPUT 25-400(%)
100
20
20
20
400
1
320
105
15
30
30
Press [CUSTOM SETTING] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Select 1, and
press [START] key.
press [START] key.
Select 2, and
press [START] key.
press [START] key.
Select 0, and
press [START] key.
press [START] key.
Press [START] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [START] key or
press [CUSTOME SETTING] key.
press [CUSTOME SETTING] key.
Press [CUSTOM SETTING] key.
Or copying is terminated.
Or copying is terminated.
Default Set range
0 TRAY SELECT
Paper feed tray selection
-
1 ~ 5
1 COPY START
Copy start (Initial value)
-
2 MAGNIFICATION Print magnification ratio
setup
-
25 ~ 400
3 L1
Document scan start
position adjustment
position adjustment
-
0 ~ 999
4 L2
Resist roller clutch ON
timing adjustment value
timing adjustment value
-
0 ~ 999
5 IMAGE LOSS
(LEAD)
Rear edge void quantity
adjustment value
adjustment value
15
0 ~ 99
6 IMAGE LOSS
(SIDE)
Lead edge image loss
quantity set value
quantity set value
20
0 ~ 99
7 DENB
Side image loss quantity
set value
set value
35
0 ~ 99
8 DENA
Lead edge void quantity
set value
set value
35
0 ~ 99
9 FR_VOIDFR
Void quantity adjustment
value
value
35
0 ~ 99
Normal display
NOW COPYING
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
2
TRAY2
3
TRAY3
4
TRAY4
5
Manual feed
Set range
25 - 400%
) !" #$%&'
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man12) service manuals if exist.