Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ▷ View online
AR-M350 SIMULATIONS 10-26
<List of set values>
<List of set values>
<List of set values>
<List of set values>
24-5
Purpose
Data clear
Function (Content)
Used to reset the developer counter.
(The developer counter of the DV unit installed is
reset.)
(The developer counter of the DV unit installed is
reset.)
Section
Process
(OPC drum, developing, transfer, cleaning)
(OPC drum, developing, transfer, cleaning)
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
Developer cartridge counter
24-6
Purpose
Data clear
Function (Content)
Used to reset the copy counter.
Section
Item
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
Copy effective paper counter
1
SIMULATION 24-5
DV CARTRIDGE COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
DV CARTRIDGE COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 24-5
DEVELOPER COUNTER DATA CLEAR. PRESS START.
1. DV CARTRIDGE
DEVELOPER COUNTER DATA CLEAR. PRESS START.
1. DV CARTRIDGE
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
1
SIMULATION 24-6
COPY COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
COPY COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 24-6
COPY COUNTER DATA CLEAR. PRESS START.
1. COPY
COPY COUNTER DATA CLEAR. PRESS START.
1. COPY
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
24-7
Purpose
Data clear
Function (Content)
Used to clear the OPC drum counter and the
toner cartridge counter.
(Perform when the OPC drum is replaced.)
toner cartridge counter.
(Perform when the OPC drum is replaced.)
Section
Process
(OPC drum, developing, transfer, cleaning)
(OPC drum, developing, transfer, cleaning)
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
Drum cartridge counter
2
Toner cartridge counter
24-9
Purpose
Data clear
Function (Content)
Used to clear the printer print counter.
(After completion of maintenance, this counter
must be cleared.)
(After completion of maintenance, this counter
must be cleared.)
Section
Printer
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
Printer counter
2
Other effective paper counter
1
SIMULATION 24-7
DRUM CARTRIDGE COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
DRUM CARTRIDGE COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 24-7
DRUM/TONER COUNTER DATA CLEAR. SELECTAND PRESS START.
1. DRUM CARTRIDGE
2. TONER CARTRIDGE
DRUM/TONER COUNTER DATA CLEAR. SELECTAND PRESS START.
1. DRUM CARTRIDGE
2. TONER CARTRIDGE
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
1
SIMULATION 24-9
PRINTER COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
PRINTER COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 24-9
PRINTER/OTHERS COUNTER DATA CLEAR. SELECT1-2, AND
PRESS START.
1. PRINTER
2. OTHERS
PRINTER/OTHERS COUNTER DATA CLEAR. SELECT1-2, AND
PRESS START.
1. PRINTER
2. OTHERS
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
'* !"#$%&
AR-M350 SIMULATIONS 10-27
<List of set values>
<List of set values>
<List of set values>
24-10
Purpose
Data clear
Function (Content)
Used to clear the FAX counter.
Section
FAX
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
FAX SEND: Number of times of FAX sending
2
FAX RECEIVE: Number of times of FAX reception
3
FAX OUTPUT: FAX print quantity
4
SEND IMAGES: Sending quantity
5
SEND TIME: Time for sending
6
RECEIVE TIME: Time for reception
1
SIMULATION 24-10
FAX SEND COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
FAX SEND COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 24-10
FAX COUNTER DATA CLEAR. SELECT1-6, AND PRESS START.
1. FAX SEND
2. FAX RECEIVED
3. FAX OUTPUT
4. SEND IMAGES
5. SEND TIME
6. RECEIVE TIME
FAX COUNTER DATA CLEAR. SELECT1-6, AND PRESS START.
1. FAX SEND
2. FAX RECEIVED
3. FAX OUTPUT
4. SEND IMAGES
5. SEND TIME
6. RECEIVE TIME
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
24-11
Purpose
Data clear
Function (Content)
Used to reset the drum rotation time, toner motor
rotation time, and developer rotation time
counters. The developer counter of the DV unit
installed is reset.
rotation time, and developer rotation time
counters. The developer counter of the DV unit
installed is reset.
Section
Process
(OPC drum, developing, transfer, cleaning)
(OPC drum, developing, transfer, cleaning)
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
Drum rotating time (cartridge)
2
Developing unit rotating time (cartridge)
3
Toner supply time (cartridge)
24-15
Purpose
Data clear
Function (Content)
Used to clear each counter in the scanner mode.
Section
Item
Item
Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1
Document scan counter in the network scanner mode
2
Number of times of mail sending
3
Number of times of FTP sending
1
SIMULATION 24-11
DRUM ROTATION COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
DRUM ROTATION COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 24-11
TIMER DATA CLEAR. SELECT1-3, AND PRESS START.
1. DRUM ROTATION (CARTRIDGE)
2. DV ROTATION (CARTRIDGE)
3. TONER SUPPLY (CARTRIDGE)
TIMER DATA CLEAR. SELECT1-3, AND PRESS START.
1. DRUM ROTATION (CARTRIDGE)
2. DV ROTATION (CARTRIDGE)
3. TONER SUPPLY (CARTRIDGE)
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
1
SIMULATION 24-15
NETWORK SCANNER ORIGINAL COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
NETWORK SCANNER ORIGINAL COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 24-15
NETWORK SCANNER COUNTER CLEAR.SELECT1-3, AND PRESS START.
1.NETWORK SCANNER ORIGINAL COUNTER
2.MAIL COUNTER
3.FTP COUNTER
NETWORK SCANNER COUNTER CLEAR.SELECT1-3, AND PRESS START.
1.NETWORK SCANNER ORIGINAL COUNTER
2.MAIL COUNTER
3.FTP COUNTER
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
'+ !"#$%&
AR-M350 SIMULATIONS 10-28
Note: Open front cover before entering SIM for Auto adjust.
<List of target counters>
Main code 25
25-1
Purpose
Operation test, check
Function (Content)
Used to check the operations of the main drive
section (excluding the scanner (reading) section)
and the toner density sensor. (The toner density
sensor output can be monitored.)
section (excluding the scanner (reading) section)
and the toner density sensor. (The toner density
sensor output can be monitored.)
Section
Drive
Item
Operation
Operation/Procedure the toner density control sensor value is
displayed. Press START key, and the main motor
will rotate to start monitoring the toner density
control sensor.
will rotate to start monitoring the toner density
control sensor.
25-2
Purpose
Setup
Function (Content)
Used to initialize the toner density when
replacing developer. (Auto adjustment)
replacing developer. (Auto adjustment)
Section
Process
(OPC drum, developing, transfer, cleaning)
(OPC drum, developing, transfer, cleaning)
Item
Operation/Procedure The toner density control sensor value is
Operation/Procedure The toner density control sensor value is
displayed. Press START key, and the main motor
will rotate. After stirring for 2 min, the toner
density control sensor value is sampled 10 times
and the average value is stored.
will rotate. After stirring for 2 min, the toner
density control sensor value is sampled 10 times
and the average value is stored.
SIMULATION 25-1
DV MONITOR. PRESS START.
DV MONITOR. PRESS START.
128
SIMULATION 25-1
DV MONITOR. EXECUTING...
DV MONITOR. EXECUTING...
128
Press [START] key.
Press [CUSTOM SETTING] key to stop.
Or stop after 2min.
SIMULATION 25-2
AUTOMATIC DV ADJUSTMENT. PRESS START.
AUTOMATIC DV ADJUSTMENT. PRESS START.
128
SIMULATION 25-2
AUTOMATIC DV ADJUSTMENT. EXECUTING...
AUTOMATIC DV ADJUSTMENT. EXECUTING...
128
Press [START] key.
Press [CUSTOM SETTING] key to stop.
Or stop after 2min.
Main code 26
26-3
Purpose
Setup
Function (Content)
Used to set the specification mode of the auditor.
Setup must be made according to the use
conditions under auditor.
Setup must be made according to the use
conditions under auditor.
Section
Auditor
Item
Spec
Operation/Procedure The auditor setting is performed. (Default: 1)
26-5
Purpose
Setup
Function (Content)
Used to set the count mode of the total counter
and the maintenance counter.
and the maintenance counter.
Section
Item
Item
Spec
Operation/Procedure 1) Setting of the count-up number of A3/WLT
paper passing (1 or 2) is made.
The current set value is highlighted on the
right side of the item.
The current set value is highlighted on the
right side of the item.
2) Setting of the count-up number of the selected
counter is made.
1: 1 count up
2: 2 counts up (Default : 2)
2: 2 counts up (Default : 2)
1
Total counter
2
Maintenance counter/drum cartridge counter
3
Developer cartridge counter
SIMULATION 26-3
AUDITOR SETUP. SELECT 1-3, AND PRESS START.
1. P10
2. VENDOR
3. OTHERS
AUDITOR SETUP. SELECT 1-3, AND PRESS START.
1. P10
2. VENDOR
3. OTHERS
1
SIMULATION 26-5
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS
START.
1. TOTAL COUNTER
2. MAINTENANCE(DRUM) COUNTER
3. DV CARTRIDGE COUNTER
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS
START.
1. TOTAL COUNTER
2. MAINTENANCE(DRUM) COUNTER
3. DV CARTRIDGE COUNTER
1
SIMULATION 26-5
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS
START.
1. TOTAL COUNTER
(1 : 1COUNT UP 2 : 2COUNT UP)
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS
START.
1. TOTAL COUNTER
(1 : 1COUNT UP 2 : 2COUNT UP)
1
1
1
1
Press [START] key.
Press [CUSTOM SETTING] key.
', !"#$%&
AR-M350 SIMULATIONS 10-29
*
When NIC is installed, reset cannot be performed. Therefore, the
power must be turned off/on.
*
This simulation cannot change the FAX destination. Use SIM 66-2 to
change the FAX destination.
<List of destinations>
<List of set values>
<List of set values>
<List of set values>
<List of set values>
26-6
Purpose
Setup
Function (Content)
Used to set the specification according to the
destination.
destination.
Section
Item
Item
Spec
Operation/Procedure After setting the destination, the power is turned
off/on.
1
United States of America
2
Canada
3
Inch series EX
4
Japan
5
AB series B5
6
Europe
7
UK
8
Australia
9
AB series A5
10
China
26-10
Purpose
Setup
Function (Content)
Used to set the trial mode of the network
scanner.
scanner.
Section
Item
Item
Operation
Operation/Procedure The network scanner trial mode is set.
(Testing scanner without product key is limited to
500 sheets.) (Default: 0)
500 sheets.) (Default: 0)
0
Trial mode cancel
1
Trial mode start
SIMULATION 26-6
DESTINATION SETUP. SELECT 1-10, AND PRESS START.
1. USA
DESTINATION SETUP. SELECT 1-10, AND PRESS START.
1. USA
2. CANADA 3. INCH
4. JAPAN
5.AB _B
6. EUROPE
7. UK
8. AUSTRALIA
9. AB_A
10. CHINA
1
SIMULATION 26-10
NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS
START.
0.END
1.START
NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS
START.
0.END
1.START
1
26-18
Purpose
Setup
Function (Content)
Used to set Enable/Disable of toner save
operation.
(This simulation is enabled only in Japan and UK
versions. (Depends on SIM 26-6 (Destination)
setup).
For the other destinations, user program P22
allows to make the similar setup.)
operation.
(This simulation is enabled only in Japan and UK
versions. (Depends on SIM 26-6 (Destination)
setup).
For the other destinations, user program P22
allows to make the similar setup.)
Section
Item
Item
Spec
Operation/Procedure The toner mode setup is made. (Default: 1)
0
Toner save mode is enabled.
1
Toner save mode is disabled.
26-30
Purpose
Setup
Function (Content)
Used to set the operation mode conforming to
the CE mark (Europe standards). (For flickers
when driving the fusing heater lamp.)
the CE mark (Europe standards). (For flickers
when driving the fusing heater lamp.)
Section
Item
Item
Spec
Operation/Procedure
0
No control of CE mark
1
Control of CE mark
26-35
Purpose
Setup
Function (Content)
Used to set whether the trouble history of SIM
22-4 is displayed as one-time trouble or
continuous troubles when two or more number of
a same trouble occurred.
22-4 is displayed as one-time trouble or
continuous troubles when two or more number of
a same trouble occurred.
Section
Item
Item
Spec
Operation/Procedure The trouble memory storing method is set.
(Default: 0)
0
Only once (If same as the previous one, it is not stored.)
1
Any times (Though same as the previous one, it is stored.)
SIMULATION 26-18
TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START.
0. YES
1. NO
TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START.
0. YES
1. NO
1
SIMULATION 26-30
CE MARK CONTROL SETTING. SELECT 0-1, AND PRESS START.
0. NO
1. YES
CE MARK CONTROL SETTING. SELECT 0-1, AND PRESS START.
0. NO
1. YES
1
SIMULATION 26-35
TROUBLE MEMORY MODE SETTING. SELECT 0-1, AND PRESS
START.
0. ONCE
1. ANY
TROUBLE MEMORY MODE SETTING. SELECT 0-1, AND PRESS
START.
0. ONCE
1. ANY
1
'- !"#$%&
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man12) service manuals if exist.