Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ▷ View online
AR-M350 SIMULATIONS 10-30
*
This simulation is ignored in the AR model, that is, the operation is
continued.
<List of set values>
<List of set values>
*
The following counters are not counted up.
<List of set values>
(Japan only)
<List of set values>
26-38
Purpose
Setup
Function (Content)
Used to stop printing when developer life is
expired.
expired.
Section
Other
Item
Operation
Operation/Procedure Print enable/disable is set when the developer
cartridge is expired in a DM machine. (Default: 1)
0
Print continue
1
Print stop
26-41
Purpose
Setup
Function (Content)
Used to set Enable/Disable of the magnification
ratio auto selection function (AMS) in the
pamphlet copy mode.
ratio auto selection function (AMS) in the
pamphlet copy mode.
Section
Item
Item
Spec
Operation/Procedure Pamphlet mode AMS setting is enabled or
disabled. Press START key to save.
(Europe : 1, Others : 0)
(Europe : 1, Others : 0)
0
AMS setting disabled
1
AMS setting enabled
26-52
Purpose
Setup
Function (Content)
Used to set Enable/Disable of count-up when
white paper is discharged.
(White paper means the index paper (without
copying) in the OHP index paper insertion mode,
the front/rear covers (without copying) in the
cover insertion mode, and white paper in the
duplex exit mode (CA, etc.).)
white paper is discharged.
(White paper means the index paper (without
copying) in the OHP index paper insertion mode,
the front/rear covers (without copying) in the
cover insertion mode, and white paper in the
duplex exit mode (CA, etc.).)
Section
Paper transport (Paper exit, switchback,
transport)
transport)
Item
Operation/Procedure Count-up setting of white paper exit mode is
Operation/Procedure Count-up setting of white paper exit mode is
made. Press START key to save. (Default: 0 for
Japan and Australia, 1 for the others)
Japan and Australia, 1 for the others)
•Copies counter
•Total counter
•Printer counter
•Effective paper counter
•Department control counter
0
Count-up is not made.
1
Count-up is made
SIMULATION 26-38
DEVELOPER LIFE END SETTING. SELECT 0-1, AND PRESS START.
0. PRINT CONTINUE
1. PRINT STOP
DEVELOPER LIFE END SETTING. SELECT 0-1, AND PRESS START.
0. PRINT CONTINUE
1. PRINT STOP
1
SIMULATION 26-41
PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS
START.
0. NO
1. YES
PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS
START.
0. NO
1. YES
1
SIMULATION 26-52
BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS START.
0. NO(NO COUNT UP)
1. YES (COUNT UP)
BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS START.
0. NO(NO COUNT UP)
1. YES (COUNT UP)
1
Main code 27
27-1
Purpose
Setup
Function (Content)
Used to set the operation specifications when a
communication trouble occurs between the host
computer and MODEM (machine side).
(When a communication trouble occurs between
the host computer and MODEM (machine side),
self diag display (U7-00) is displayed and setup
is made to inhibit or allow printing. )
communication trouble occurs between the host
computer and MODEM (machine side).
(When a communication trouble occurs between
the host computer and MODEM (machine side),
self diag display (U7-00) is displayed and setup
is made to inhibit or allow printing. )
Section
Communication (RIC/MODEM)
Item
Spec
Operation/Procedure Yes/No of communication trouble between
PC/MODEM is set. (Default: 0)
0
U7-00 is not displayed in a communication trouble.
1
U7-00 is displayed in a communication trouble.
27-5
Purpose
Setup
Function (Content)
Used to enter the machine tag No.
(This function allows to check the machine tag
No. from the computer.)
(This function allows to check the machine tag
No. from the computer.)
Section
Communication (RIC/MODEM)
Item
Data
Operation/Procedure The tag number is set. The current value is
displayed on PRESENT column. Enter a new tag
number with 10 digit key pad and press START
to store.
number with 10 digit key pad and press START
to store.
SIMULATION 27-1
DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.
0. YES
1. NO
DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.
0. YES
1. NO
1
SIMULATION 27-5
TAG # SETTING. INPUT VALUE, AND PRESS START.
PRESENT : 00010000
NEW :
TAG # SETTING. INPUT VALUE, AND PRESS START.
PRESENT : 00010000
NEW :
00009999
!"#$%&
AR-M350 SIMULATIONS 10-31
<List of display values>
<List of display values>
<List of display values>
Main code 30
30-1
Purpose
Operation test, check
Function (Content)
Used to check the operations of the sensors and
detectors in the paper feed, paper transport, and
paper exit sections and their control circuits.
detectors in the paper feed, paper transport, and
paper exit sections and their control circuits.
Section
Item
Item
Operation
Operation/Procedure Then sensors of the machine are checked.
The sensor name is highlighted when it is
detected.
detected.
PPD1
Resist roller front paper detection
POD1
Fusing rear transport detection 1
POD2
Fusing rear transport detection 2
POD3
Paper full detection
DVCRUin
DV unit version detection
PRCRUin
Process unit version detection
DSWL
Cabinet open detection
DSWF
Machine front door
30-2
Purpose
Operation test, check
Function (Content)
Used to check the operations of the sensors and
detectors in the paper feed section and their
control circuits. (The operations of the sensors
and detectors in the paper feed section can be
monitored on the LCD display.)
detectors in the paper feed section and their
control circuits. (The operations of the sensors
and detectors in the paper feed section can be
monitored on the LCD display.)
Section
Paper feed
Item
Operation
Operation/Procedure Then sensors of the machine paper feed tray are
checked. The sensor name is highlighted when it
is detected.
is detected.
CSS1
Tray 1 insertion detection MCSS1 MP tray size detection 1
PED
Tray 1 paper empty
detection
detection
MCSS2 MP tray size detection 2
LUD
Tray 1 upper limit
detection
detection
MCSS3 MP tray size detection 3
MCSET MP unit detection
MCSS4 MP tray size detection 4
MCDRS MP unit side door open
detection
MP Tray
size
size
(The detection size of MP
tray is displayed.)
tray is displayed.)
MCPPD MP tray transport
detection
MPFSET Manual feed tray
detection
MCLUD MP tray upper limit
detection
MPED
Manual feed tray paper
empty detection
empty detection
MCPED MP tray paper empty
detection
MPLD
Manual feed length
detection
detection
MCSPD MP tray remaining
quantity detection
MPLS1
Manual feed pull-out
sensor 1
sensor 1
MPLS2
Manual feed pull-out
sensor 2
sensor 2
Bypass
Tray
size
Tray
size
(The detection size of
manual feed tray is
displayed.)
manual feed tray is
displayed.)
SIMULATION 30-1
SENSOR CHECK..
PPD1 POD1 POD2
SENSOR CHECK..
PPD1 POD1 POD2
POD3
DVCRUin PRCRUin
DSWL
DSWF
SIMULATION 30-2
TRAY SENSOR CHECK..
CSS1 PED LUD
TRAY SENSOR CHECK..
CSS1 PED LUD
MCSET
MCDRS MCPPD MCLUD MCPED MCSPD MCSS1 MCSS2
MCSS3 MCSS4
(MP Tray size:
A4
)
MPFSET
MPED MPLD MPLS1 MPLS2
(Bypass Tray size:
A3
)
Main code 40
40-1
Purpose
Operation test, check
Function (Content)
Used to check the operations of the manual
paper feed tray paper size detectors and their
control circuit. (The operations of the manual
paper feed tray paper size detectors can be
monitored on the LCD display.)
paper feed tray paper size detectors and their
control circuit. (The operations of the manual
paper feed tray paper size detectors can be
monitored on the LCD display.)
Section
Paper feed
Item
Operation
Operation/Procedure The sensors of the manual feed tray are
checked. The sensor name is highlighted when it
is detected.
is detected.
MPLD
Manual feed tray length detection
MPLS1
Manual feed pull-out sensor 1
MPLS2
Manual feed pull-out sensor 2
Bypass Tray
width size
width size
(The detected width of manual feed tray is displayed.)
A4/A3, 11x, B5/B4, 8.5x, A4R, B5R, A5R, 5.5x, 7.25x,
EXTRA
A4/A3, 11x, B5/B4, 8.5x, A4R, B5R, A5R, 5.5x, 7.25x,
EXTRA
SIMULATION 40-1
BYPASS TRAY SENSOR CHECK.
BYPASS TRAY SENSOR CHECK.
MPLD
MPLS1 MPLS2
(Bypass Tray width size:
A4/A3
)
!" #$%&
AR-M350 SIMULATIONS 10-32
*
This adjustment is performed only when the width detection volume
is replaced.
Normally use SIM 40-7 for input.
Normally use SIM 40-7 for input.
<List of set values>
<List of display values>
40-2
Purpose
Adjustment, setup
Function (Content)
Used to adjust the detection level of the manual
paper feed tray paper width volume.
paper feed tray paper width volume.
Section
Paper feed
Item
Operation
Operation/Procedure The manual feed tray size is adjusted.
1) Extend the guide to the MAX. position. Select
1 and press START. When COMPLETE is
displayed, press CUSTOM SETTING to
return to the initial screen.
2) Move the guide to A4R position. Select 2 and
press START. When COMPLETE is
displayed, press CUSTOME SETTING to
return to the initial screen.
return to the initial screen.
3) Move the guide to A5R position. Select 3 and
press START. When COMPLETE is
displayed, press CUSTOME SETTING to
displayed, press CUSTOME SETTING to
return to the initial screen.
4) Move the guide to MIN. position in the initial
screen. Select 4 and press START. When
COMPLETE is displayed, the adjustment is
completed.
If ERROR is displayed in procedures 1) - 4),
repeat the adjustment again."
repeat the adjustment again."
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START.
1.MAX. POSITION
2.POSITION 1
3.POSITION 2
4.MIN. POSITION
BYPASS TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START.
1.MAX. POSITION
2.POSITION 1
3.POSITION 2
4.MIN. POSITION
1
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
MAX. POSITION ... COMPLETE (or "ERROR")
BYPASS TRAY ADJUSTMENT.
MAX. POSITION ... COMPLETE (or "ERROR")
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
POSITION 1 ... COMPLETE (or "ERROR")
BYPASS TRAY ADJUSTMENT.
POSITION 1 ... COMPLETE (or "ERROR")
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
POSITION 2 ... COMPLETE (or "ERROR")
BYPASS TRAY ADJUSTMENT.
POSITION 2 ... COMPLETE (or "ERROR")
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
MIN. POSITION ... COMPLETE (or "ERROR")
BYPASS TRAY ADJUSTMENT.
MIN. POSITION ... COMPLETE (or "ERROR")
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
When "1" is selected,
press [START] key.
press [START] key.
When "2" is selected,
press [START] key.
press [START] key.
When "3" is selected,
press [START] key.
press [START] key.
When "4" is selected,
press [START] key.
press [START] key.
40-7
Purpose
Adjustment, setup
Function (Content)
Used to enter the adjustment value of the
manual paper feed tray width detection level.
manual paper feed tray width detection level.
Section
Paper feed
Item
Operation
Operation/Procedure The adjustment value(Specified on the back of
the tray pull-out section) of the manual feed tray
size is entered.
size is entered.
1
Max. width(Max.)
2
Adjustment point 1(P1)
3
Adjustment point 2(P2)
4
Min. width(Min.)
40-11
Purpose
Operation test, check
Function (Content)
Used to check the width detection level of the
multi-purpose tray paper width detector.
multi-purpose tray paper width detector.
Section
Paper feed
Item
Operation
Operation/Procedure The multi-purpose tray (MPT) sensors are
checked. The sensor name is highlighted when it
is highlighted.
is highlighted.
MCSS1
Multi-purpose tray size detection 1
MCSS2
Multi-purpose tray size detection 2
MCSS3
Multi-purpose tray size detection 3
MCSS4
Multi-purpose tray size detection 4
Multi Purpose
Tray width size
Tray width size
(The detected size of MPT width is displayed.)
A4/A3, 11x, B5/B4, 8.5x, A4R, B5R, A5R, 5.5x, 7.25x,
EXTRA
A4/A3, 11x, B5/B4, 8.5x, A4R, B5R, A5R, 5.5x, 7.25x,
EXTRA
1
SIMULATION 40-7
BYPASS TRAY VALUE SETTING. INPUT VALUE 0-1023, AND PRESS START.
1. MAX. POSITION
BYPASS TRAY VALUE SETTING. INPUT VALUE 0-1023, AND PRESS START.
1. MAX. POSITION
72
SIMULATION 40-7
BYPASS TRAY VALUE SETTING. SELECT 1-4, AND PRESS START.
1. MAX. POSITION :
BYPASS TRAY VALUE SETTING. SELECT 1-4, AND PRESS START.
1. MAX. POSITION :
72
2. POSITION 1 :
380
3. POSITION 2 :
710
4. MIN. POSITION :
804
Press [START] key.
Press [CUSTOM SETTING] key.
SIMULATION 40-11
MULTI PURPOSE TRAY SENSOR CHECK.
MULTI PURPOSE TRAY SENSOR CHECK.
MCSS1
MCSS2 MCSS3 MCSS4
(Multi Purpose Tray width size:
A4/A3
)
' !" #$%&
AR-M350 SIMULATIONS 10-33
<List of display values>
40-12
Purpose
Operation test, check
Function (Content)
Used to adjust the width detection level of the
multi-purpose tray paper width detector.
multi-purpose tray paper width detector.
Section
Paper feed
Item
Operation
Operation/Procedure The multi-purpose tray size is adjusted.
1) Extend the guide to the MAX. position.
Select 1 and press START.
When COMPLETE is displayed,
press CUSTOM SETTING to return to the
initial screen.
When COMPLETE is displayed,
press CUSTOM SETTING to return to the
initial screen.
2) Move the guide to MIN. position.
Select 2 and press START.
When COMPLETE is displayed,
the adjustment is completed.
When COMPLETE is displayed,
the adjustment is completed.
If ERROR is displayed in procedures 1) - 2),
repeat the adjustment again.
repeat the adjustment again.
SIMULATION 40-12
MULTI PURPOSE TRAY ADJUSTMENT. SELECT 1-2,AND PRESS
START.
1.MAX POSITION
2.MIN. POSITION
MULTI PURPOSE TRAY ADJUSTMENT. SELECT 1-2,AND PRESS
START.
1.MAX POSITION
2.MIN. POSITION
1
SIMULATION 40-12
MULTI PURPOSE TRAY ADJUSTMENT.
MAX. POSITION... COMPLETE(or "ERROR")
MULTI PURPOSE TRAY ADJUSTMENT.
MAX. POSITION... COMPLETE(or "ERROR")
SIMULATION 40-12
MULTI PURPOSE TRAY ADJUSTMENT.
MIN. POSITION... COMPLETE (or "ERROR")
MULTI PURPOSE TRAY ADJUSTMENT.
MIN. POSITION... COMPLETE (or "ERROR")
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
When "1" is selected,
press [START] key.
press [START] key.
When "2" is selected,
press [START] key.
press [START] key.
Main code 41
41-1
Purpose
Operation test, check
Function (Content)
Used to check the operations of the document
size sensor and the related circuit.
(The operation of the document size sensor can
be monitored on the LCD display.)
size sensor and the related circuit.
(The operation of the document size sensor can
be monitored on the LCD display.)
Section
Other
Item
Operation
Operation/Procedure The OC document sensor is checked.
OCSW
Original cover state
Open : Normal display
Close : Highlighted
Open : Normal display
Close : Highlighted
PD1 ~ 7
Document sensor state
No document : Normal display
Document loaded : Highlighted
No document : Normal display
Document loaded : Highlighted
41-2
Purpose
Adjustment
Function (Content)
Used to adjust the detection level of the
document size sensor.
document size sensor.
Section
Other
Item
Operation
Operation/Procedure The OC document sensor is adjusted.
1) Open the original cover. Press 1 without an
original. Press START, and COMPLETE is
displayed. Press CUSTOM SETTING to
return to the initial screen.
displayed. Press CUSTOM SETTING to
return to the initial screen.
2) Place an A3 (or WLT) paper in the initial
screen. Select 2 and press START.
When COMPLETE is displayed,
the adjustment is completed.
When COMPLETE is displayed,
the adjustment is completed.
If ERROR is displayed in procedures 1) - 2),
repeat the adjustment again.
repeat the adjustment again.
SIMULATION 41-1
PD SENSOR CHECK..
OCSW
PD SENSOR CHECK..
OCSW
PD1 PD2 PD3
PD4 PD5 PD6 PD7
(The detected sensor is highlighted.)
SIMULATION 41-2
PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START.
(PLEASE OPEN THE ORIGINAL COVER.)
1. NO ORIGINAL
2. A3 ORIGINAL
PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START.
(PLEASE OPEN THE ORIGINAL COVER.)
1. NO ORIGINAL
2. A3 ORIGINAL
1
SIMULATION 41-2
PD SENSOR ADJUSTMENT.
NO ORIGINAL ... COMPLETE (or " ERROR at
PD SENSOR ADJUSTMENT.
NO ORIGINAL ... COMPLETE (or " ERROR at
PD1 PD2
...")
A3 ORIGINAL ... INCOMPLETE
SIMULATION 41-2
PD SENSOR ADJUSTMENT.
NO ORIGINAL ... COMPLETE
A3 ORIGINAL ... COMPLETE (or " ERROR at
PD SENSOR ADJUSTMENT.
NO ORIGINAL ... COMPLETE
A3 ORIGINAL ... COMPLETE (or " ERROR at
PD1 PD2
...")
Press [CUSTOM SETTING] key.
Press [CUSTOM SETTING] key.
When "1" is selected,
press [START] key.
press [START] key.
When "2" is selected,
press [START] key.
press [START] key.
(In case of an error)
!" #$%&
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man12) service manuals if exist.