Sharp AR-M236 (serv.man12) User Manual / Operation Manual ▷ View online
67
TROUBLESHOOTING AND MAINTENANCE
5
MISFEED IN THE CENTRE TRAY
Remove the paper by pulling it into the centre tray.
MISFEED IN THE UPPER PAPER TRAY
Make sure that there is no misfed paper in the machine before pulling the tray out. (p.65)
1
Lift and pull out the upper paper tray
and then remove the misfed paper.
and then remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
2
Replace the upper paper tray.
Push the upper paper
tray in completely.
tray in completely.
3
Open and close the side cover.
Make sure that the
misfeed message is
cleared.
The message can also
be cleared by opening
and closing the front
cover.
misfeed message is
cleared.
The message can also
be cleared by opening
and closing the front
cover.
68
TROUBLESHOOTING AND MAINTENANCE
MISFEED IN THE LOWER PAPER TRAY
● Make sure that there is no misfed paper in the machine before pulling the tray out. (p.65)
● Use the following procedure to remove misfeeds that occur in the 500-sheet paper feed unit or 2 x 500-sheet paper
feed unit.
1
Open the lower side cover.
2
Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
3
If the misfed paper is not visible in
step 2, lift and pull out the lower paper
tray and remove the misfed paper.
step 2, lift and pull out the lower paper
tray and remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
4
Replace the lower paper tray.
Push the lower paper tray in completely.
5
Close the lower side cover.
Make sure that the
misfeed message is
cleared.
misfeed message is
cleared.
69
TROUBLESHOOTING AND MAINTENANCE
5
MISFEED IN THE UPPER EXIT AREA
(when a job separator tray kit or finisher (AR-FN5N) is
installed)
(when a job separator tray kit or finisher (AR-FN5N) is
installed)
If a job separator tray kit or a finisher is installed, a misfeed may occur in the upper exit area.
1
Open the upper right side cover.
2
Gently pull the misfed paper out.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
3
Close the upper right side cover.
Make sure that the misfeed message is cleared.
MISFEED IN AN OUTPUT TRAY
(when a finisher (AR-FN5N) is installed)
(when a finisher (AR-FN5N) is installed)
1
Grasp the handle of the stapler
compiler cover and pull to open the
cover.
compiler cover and pull to open the
cover.
2
Remove any misfed paper from the
transport area.
transport area.
A MISFEED HAS OCCURRED.
INFORMATION
70
TROUBLESHOOTING AND MAINTENANCE
3
If staple sort copying is being
performed, open the paper guide and
remove any misfed paper from the
stapler compiler.
performed, open the paper guide and
remove any misfed paper from the
stapler compiler.
4
Close the stapler compiler cover.
5
If the offset tray is being used, remove
any misfed paper from the offset tray.
any misfed paper from the offset tray.
6
If the top tray is being used, open the
top cover, remove any misfed paper,
and close the top cover.
top cover, remove any misfed paper,
and close the top cover.
Make sure that the
misfeed message is
cleared.
misfeed message is
cleared.
Click on the first or last page to see other AR-M236 (serv.man12) service manuals if exist.