Sharp AR-M236 (serv.man12) User Manual / Operation Manual ▷ View online
71
5
REPLACING THE TONER CARTRIDGE
To check how much toner remains in the toner cartridge (p.73), hold down the [COPY] key. The amount of toner
remaining will appear in the display. When less than 25% of the toner remains, obtain a new toner cartridge as soon
as possible. When "TONER SUPPLY IS LOW." appears in the display, be sure to have a new cartridge on hand for
replacement at any time as little toner remains. When "CHANGE THE TONER CARTRIDGE." appears in the touch
panel, the toner cartridge must be replaced. Follow these steps to replace the cartridge.
remaining will appear in the display. When less than 25% of the toner remains, obtain a new toner cartridge as soon
as possible. When "TONER SUPPLY IS LOW." appears in the display, be sure to have a new cartridge on hand for
replacement at any time as little toner remains. When "CHANGE THE TONER CARTRIDGE." appears in the touch
panel, the toner cartridge must be replaced. Follow these steps to replace the cartridge.
1
Press gently on both sides of the front
cover and pull it open.
cover and pull it open.
2
Pull the toner cartridge out while
pressing the lock release lever.
pressing the lock release lever.
When pulling out the
toner cartridge, place
your other hand on the
green part of the
cartridge.
toner cartridge, place
your other hand on the
green part of the
cartridge.
3
Remove the new toner cartridge from
the bag. Grasp both ends of the
cartridge and shake it horizontally
about 20 times. After shaking the
cartridge, remove the tape.
the bag. Grasp both ends of the
cartridge and shake it horizontally
about 20 times. After shaking the
cartridge, remove the tape.
Grasp the hand grip to
hold the cartridge. Do not
hold the cartridge by the
shutter. Be sure to only
shake the cartridge
before the tape is
removed.
hold the cartridge. Do not
hold the cartridge by the
shutter. Be sure to only
shake the cartridge
before the tape is
removed.
4
While pushing the lock release lever,
gently insert the toner cartridge along
the guides until it clicks into place.
gently insert the toner cartridge along
the guides until it clicks into place.
5
Remove the tape from the shutter. Pull
the shutter out of the toner cartridge
as shown in the illustration.
the shutter out of the toner cartridge
as shown in the illustration.
Discard the shutter.
6
Close the front cover.
When running long copy jobs or copying originals with many areas of solid black, "TONER REPLENISHMENT IN
PROGRESS." may appear in the touch panel and copying may stop even though the cartridge still has toner.
When this occurs, the toner is being replenished. Replenishment will last about two minutes. When the [START]
key (
PROGRESS." may appear in the touch panel and copying may stop even though the cartridge still has toner.
When this occurs, the toner is being replenished. Replenishment will last about two minutes. When the [START]
key (
) illuminates, press the [START] key (
) to resume copying.
Note
• After removing the toner cartridge, do not
shake it or tap it. Doing so may cause
toner to leak from the cartridge. Put the
old cartridge immediately in the bag
provided with the new cartridge.
toner to leak from the cartridge. Put the
old cartridge immediately in the bag
provided with the new cartridge.
• Dispose of the old toner cartridge in
accordance with local regulations.
Handle
Toner cartridge
lock release lever
lock release lever
Note
Tape
Shutter
About 20 times
If dirt or dust adheres to the toner cartridge,
remove it before installing the cartridge.
remove it before installing the cartridge.
Note
72
STAPLE CARTRIDGE REPLACEMENT
(when the finisher (AR-FN5N) is installed)
When the message "ADD STAPLES." appears, replace the staple cartridge as follows:
1
Open the stapler cover.
2
Grasp the green portion of the staple
box and remove the staple box from
the stapler.
box and remove the staple box from
the stapler.
3
Remove the staple cartridge from
inside the staple box.
inside the staple box.
4
Insert the new staple cartridge into the
box until it clicks into place.
box until it clicks into place.
Insert the new cartridge
by aligning the arrows on
the cartridge with those
on the box.
Check that the cartridge
has locked into place by
pulling it slightly.
by aligning the arrows on
the cartridge with those
on the box.
Check that the cartridge
has locked into place by
pulling it slightly.
5
Remove the tape from the cartridge.
6
Insert the staple box into the stapler
unit until it clicks into place.
unit until it clicks into place.
7
Close the stapler cover.
73
TROUBLESHOOTING AND MAINTENANCE
5
STAPLE JAM REMOVAL
If staples become jammed in the stapler, the message "CHECK STAPLER POSITION OR STAPLE JAM." will appear.
Follow these steps to remove the jammed staples.
Follow these steps to remove the jammed staples.
1
Open the stapler cover.
2
Grasp the green portion of the staple
box and remove the staple box from
the stapler.
box and remove the staple box from
the stapler.
3
Raise the lever at the end of the staple
box and remove the jammed staples.
box and remove the jammed staples.
4
Return the lever to its original
position.
position.
5
Insert the staple box into the stapler
unit until it clicks into place.
unit until it clicks into place.
6
Close the stapler cover.
CHECKING THE TONER QUANTITY
AND TOTAL OUTPUT COUNT
AND TOTAL OUTPUT COUNT
The approximate quantity of toner remaining and the total output count can be displayed as explained below.
● The output count shows the combined output total of the copy, fax, and printer functions.
Checking the total output count and toner quantity
Hold down the [COPY] key. The total output count and toner quantity appear while the key is held down.
• Each A3 (11" x 17") page is counted as two pages. Two sided pages are also counted as two pages.
• The amount of toner consumed will vary depending on conditions of usage and the type of originals copied.
• The amount of toner consumed will vary depending on conditions of usage and the type of originals copied.
The toner quantity display should only be used as an approximate guide.
COPY
PRINT
SPECIAL MODES
2-SIDED COPY
OUTPUT
TOTAL OUTPUT : 0,123,456
TONER QUANTITY : 100-75%
A4
A3
Note
74
CLEANING THE MACHINE
DOCUMENT GLASS AND DOCUMENT COVER/RSPF
If the document glass, document cover/RSPF, or scanning glass for originals fed from the RSPF (the long narrow
glass surface on the right side of the document glass) become dirty, the dirt may appear on copies. Always keep
these parts clean.
Stains or dirt on the document glass/document cover/RSPF will also be copied. Wipe the document glass, the
document cover, the RSPF and the scanning window on the document glass with a soft, clean cloth.
If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
glass surface on the right side of the document glass) become dirty, the dirt may appear on copies. Always keep
these parts clean.
Stains or dirt on the document glass/document cover/RSPF will also be copied. Wipe the document glass, the
document cover, the RSPF and the scanning window on the document glass with a soft, clean cloth.
If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
THE BYPASS TRAY PAPER FEED ROLLER
If misfeeds occur frequently when feeding envelopes or other thick paper from the bypass tray, wipe the paper feed
roller at the feed slot of the bypass tray with a soft, clean cloth moistened with alcohol or water.
roller at the feed slot of the bypass tray with a soft, clean cloth moistened with alcohol or water.
Do not spray flammable cleaner gas. Gas from the spray may come in contact with the internal
electrical components or high-temperature parts of the fusing unit, creating a risk of fire or
electrical shock.
electrical components or high-temperature parts of the fusing unit, creating a risk of fire or
electrical shock.
Surface of document glass
Underside of document cover/RSPF
Scanning glass
Warning
Scanning glass for RSPF
Bypass tray paper feed roller
Click on the first or last page to see other AR-M236 (serv.man12) service manuals if exist.