DOWNLOAD Sharp AR-FX5 (serv.man6) Service Manual ↓ Size: 1.96 MB | Pages: 88 in PDF or view online for FREE

■

These special accessories must be used with the device.

■

This equipment complies with the requirements of Directive 1999/5/EC.

Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG.

Cet appareil est conforme aux exigences de la directive 1999/5/CE.

Este aparato satisface las exigencias de las Directiva 1999/5/CE.

Quest'apparecchio è conforme ai requisiti delle direttiva 1999/5/CE.

Dit apparaat voldoet aan de eisen van de richtlijn 1999/5/EG.

Este equipamento obedece às exigências da directiva 1999/5/CE.

Denna utrustning uppfyller kraven enligt direktiv 1999/5/EC.

Dette udstyr overholder kravene i direktiv 1999/5/EF.

Dette produktet oppfyller kravene i direktiv 1999/5/EC.

Tämä laite täyttää direktiivi 1999/5/EY. 

This equipment has been tested according to the pan-European CTR-21 regulation.
It will operate on all analogue telephone networks which comply with the CTR-21.
Please contact your dealer or network operator, if you are not sure whether your network operates according to
CTR-21.

■

General
"The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the
item complies with minimum conditions for connection to its network. It indicates no endorsement of the product
by Telecom, nor dose it provide any sort of warranty. Above all, it provides no assurance that any item will work
correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it
imply that any product is compatible with all of Telecom's network services. In particular the higher speeds which
this modem is capable of, can only be achieved in ideal conditions."

"This equipment shall not be used in any manner which could constitute a nuisance to other Telecom customers."

This equipment shall not be set up to make automatic calls to the Telecom '111' Emergency Service.

To avoid telephone charges for local calls, be sure to store numbers "without" area code in your rapid or speed dial
locations.

This equipment may not provide for the effective hand-over of a call to another device connected to the same line.

Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.

Several points must be kept in mind when using this product as a facsimile.
Please note the following:

■

Information about settings and programming that are required before the fax functionality can be used is located in "Points
to Check and Programming after Installation" on page 1-2 of this manual. Please read this section and perform the
required settings and programming.

■

THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED
OF PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE
REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
• When the battery dies, settings and programmed information will be lost. Be sure to keep a written record of the

settings and programmed information. (Refer to page 6-14.)

• The life of the lithium battery is approximately 5 years if the main switch and fax power switch are kept continually

off.

■

• If a thunderstorm occurs, we recommend that you unplug the power cord from the power outlet. Information will

be retained in memory even if the power cord is unplugged.

Thank you for purchasing this product. This manual only explains the facsimile functions of the product. For information
on loading paper, replacing toner cartridges, clearing paper jams, handling peripheral units, and other printer-related
information, please refer to your "Operation manual (for printer operation and general information)".
Additional manuals have been provided for copy and network scanner features. Please refer to these as necessary.
This manual assumes that several options have been installed.

Fax functions cannot be used when the power is
turned off.

TEL

LINE

NOTE
In this manual, American spellings are used.

INTRODUCTION ................................................... 0-1

TO USE THIS PRODUCT CORRECTLY
AS A FACSIMILE ................................................... 0-1

IMPORTANT SAFETY INFORMATION ................. 0-4

NOTICE FOR USERS IN AUSTRALIA AND

NEW ZEALAND ..................................................... 0-4

LINE CONNECTION ............................................. 1-2

POINTS TO CHECK AND PROGRAMMING

AFTER INSTALLATION ......................................... 1-2

A LOOK AT THE OPERATION PANEL .................. 1-3

●

FAX MODE (CONDITION SETTING SCREEN) .. 1-4

ORIGINALS ........................................................... 1-6

●

ORIGINALS THAT CAN BE FAXED ................ 1-6

LOADING A DOCUMENT ..................................... 1-7

●

USING THE AUTO DOCUMENT FEEDER ..... 1-7

●

USING THE DOCUMENT GLASS .................. 1-7

CHECKING THE SIZE OF A LOADED ORIGINAL .... 1-8

●

MANUALLY SETTING THE SCANNING SIZE ... 1-8

SELECTING RESOLUTION

AND EXPOSURE SETTINGS ............................... 1-9

●

SELECTING THE RESOLUTION .................... 1-9

●

SELECTING THE EXPOSURE ..................... 1-10

CONVENIENT DIALING METHODS ................... 1-11

SENDING A FAX ................................................... 2-2

●

BASIC PROCEDURE FOR SENDING FAXES .... 2-2

●

TRANSMISSION BY AUTO-DIALING ............. 2-5

●

TRANSMITTING A TWO-SIDED DOCUMENT ..... 2-5

PRIORITY TRANSMISSION OF A STORED JOB .... 2-6

CANCELING A FAX TRANSMISSION ................... 2-6

RECEIVING FAXES .............................................. 2-7

●

RECEIVING A FAX ......................................... 2-7

Page

SENDING THE SAME DOCUMENT

TO MULTIPLE DESTINATIONS IN A SINGLE OPERATION

 (BROADCAST TRANSMISSION) ......................... 3-2

●

USING BROADCAST TRANSMISSION .......... 3-3

AUTOMATIC TRANSMISSION AT A SPECIFIED TIME

(TIMER TRANSMISSION) ..................................... 3-4

●

SETTING UP A TIMER TRANSMISSION ....... 3-4

TRANSMISSION AND RECEPTION USING

THE POLLING FUNCTION ................................... 3-5

●

USING THE POLLING FUNCTION ................. 3-6

●

USING POLLING MEMORY ........................... 3-7

OWN NUMBER SENDING .................................... 3-9

FAXING A DIVIDED ORIGINAL

(DUAL PAGE SCAN) ........................................... 3-10

PROGRAMMING FREQUENTLY USED OPERATIONS .... 3-11

●

USING A PROGRAM .................................... 3-11

TRANSFERRING RECEIVED FAXES

TO ANOTHER MACHINE

WHEN PRINTING IS NOT POSSIBLE ................ 3-12

●

USING THE TRANSFER FUNCTION ........... 3-12

TRANSMISSION BETWEEN MACHINES

SUPPORTING F-CODES ...................................... 4-2

●

MEMORY BOXES AND

SUB-ADDRESSES/PASSCODES

REQUIRED FOR F-CODE TRANSMISSION .. 4-2

●

ENTERING A SUB-ADDRESS AND PASSCODE

FOR A MEMORY BOX IN THE OTHER MACHINE ..... 4-3

●

CREATING A MEMORY BOX

FOR F-CODE TRANSMISSION ...................... 4-3

F-CODE POLLING MEMORY ............................... 4-4

●

USING F-CODE POLLING MEMORY ............. 4-4

●

PROCEDURE FOR F-CODE POLLING .......... 4-5

Page