Sharp AR-505 (serv.man9) Service Manual ▷ View online
3
3 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors
in the sorter and the related circuit.
in the sorter and the related circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
The display differs depending on the unit (sorter, fin-
isher) installed.
The operations of the sensors and detectors in the
sorter and the finisher section are displayed.The active
sensors and detectors are highlighted.
isher) installed.
The operations of the sensors and detectors in the
sorter and the finisher section are displayed.The active
sensors and detectors are highlighted.
In the case of AR-SS1
PIS
Paper entry port sensor
PSFT
Paper empty sensor
THLS
Upper limit sensor
TLLS
Lower limit sensor
THPS
Bin home sensor
PSFT0
Take-out position sensor
SPHPS
Alignment rod home sensor
CHPS
Holder home sensor
SHPSW
Stapler home switch
PSFSU
Stapler paper sensor
SSFSU
Stapler empty sensor
SSSW
Joint section door sensor
SCSW
Staple unit section door sensor
In the case of AR-FN1
JGHP
Jogger motor home sensor
READY
Stapler self priming sensor
PSHP
Pusher motor home sensor
STUHP
Staple unit home sensor
T2PF
Tray 2 paper full sensor
STND
Stapler replacement sensor
EVRE
Elevator motor encoder
OFHP
Offset home sensor
STHP
Staple home sensor
INPD
Paper entry sensor
RVPD
Reverse paper exit sensor
PGOP
Upper transport PG open/close sensor
PFD1
Transport sensor 1
PFD2
Transport sensor 2
PFD3
Transport sensor 3
PFD4
Transport sensor 4
T3OD
Tray 3 paper exit sensor
STID
Staple tray paper entry sensor
STPD
Staple paper sensor
T1PF
Tray 1 paper full sensor
T3UP
Tray 3 upper limit sensor
T3DN
Tray 3 lower limit sensor
LSTS
Stapler sensor
NCTS
Staple cartridge sensor
PWD
Power off detection
DSW1
Copier connection detection
DSW2
Top door open/close detection
DSW3
Front door open/close detection
In the case of AR-FN2/FN3
JGHP
Jogger motor home sensor
READY
Stapler self priming sensor
PSHP
Pusher motor home sensor
STORHP
ST paper exit roller pressure release clutch home
sensor
sensor
STUHP
Staple unit home sensor
T2PF
Tray 2 paper full sensor
STND
Stapler replacement sensor
EVRE
Elevator motor encoder
OFHP
Offset home sensor
STHP
Staple home sensor
INPD
Paper entry sensor
T3PDHP
Tray 3 paper exit roller paddler home sensor
PFD2
Transport sensor 2
PFD3
Transport sensor 3
PFD4
Transport sensor 4
T3OD
Tray 3 paper exit sensor
STID
Staple tray paper entry sensor
STPD
Staple paper sensor
T1PF
Tray 1 paper full sensor
STID2
Staple tray paper-in sensor
T3UP
Tray 3 upper limit sensor
AR-505
8/6/1999
7 – 8
T3DN
Tray 3 lower limit sensor
LSTS
Stapler sensor
NCTS
Staple cartridge sensor
PWD
Power off detection
DSW1
Copier connection detection
DSW2
Top door open/close detection
DSW3
Front door open/close detection
3 - 3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the loads in the sorter
and the control circuit.
and the control circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
The display differs depending on the unit (sorter, fin-
isher) which is installed.
isher) which is installed.
1. The names of the loads which can be operated are displayed.
The selected load is highlighted.
2. Press the [EXECUTE] key, and the selected load is operated.
During the operation of the load, the [EXECUTE] key is high-
lighted. If the [EXECUTE] key is pressed when it is highlighted,
the operation is interrupted.
lighted. If the [EXECUTE] key is pressed when it is highlighted,
the operation is interrupted.
In the case of AR-SS1
DTM
Transport motor
DCM
Holder motor
BZ
Buzzer
TMM
Bin shift motor
DSM
Alignment motor
SAM
Stapler drive motor
In the case of AR-FN1
PSM
Pusher motor
JGM
Jogger motor
STUM
Staple unit shift motor
FML
Main drive motor low transport speed
FMH
Main drive motor high transport speed
RVM
Reverse motor
EVM
Elevator motor
OFM
Offset motor
INGSL
Paper entry gate solenoid
T3UPSL
Tray 3 upper limit solenoid
OG1SL
Paper exit gate 1 solenoid
OG2SL
Paper exit gate 2 solenoid
OG3SL
Paper exit gate 3 solenoid
RRSL
Reverse roller pressure release solenoid
SPSL
Short path select solenoid
STSL
ST paper holding solenoid
T12CL
Tray 1 and tray 2 speed reduction clutch
PDCL
Paddler clutch
STOPCL
ST paper exit roller pressure clutch
T3SLCL
Tray 3 speed reduction clutch
STM
Staple motor
T3ORSL
Tray 3 normal speed clutch
In the case of AR-FN2/FN3
PSM
Pusher motor
JGM
Jogger motor
STUM
Staple unit shift motor
FM
Main drive motor
T3OM
Tray 3 paper exit drive motor
EVM
Elevator motor
OFM
Offset motor
T3PDSL
Tray 3 paper exit paddler solenoid
STPDSL
ST paddler solenoid
OG1SL
Paper exit gate 1 solenoid
OG2SL
Paper exit gate 2 solenoid
OG3SL
Paper exit gate 3 solenoid
STSL
ST paper holding solenoid
T12CL
Tray 1 and tray 2 speed reduction clutch
PDCL
Paddler clutch
STOPCL
ST paper exit roller pressure clutch
STM
Staple motor
PPSL
Paper holding solenoid
AR-505
7 – 9
8/6/1999
3 - 6
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the finisher stacking capability. (Used to
adjust the stop position of the finisher paper width di-
rection alignment plate (jogger). This adjustment is
made by changing the width direction alignment plate
home position by the software.)
adjust the stop position of the finisher paper width di-
rection alignment plate (jogger). This adjustment is
made by changing the width direction alignment plate
home position by the software.)
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
1. Select B mode with [
] and [
¯
] keys.
2. Select the paper size by entering the numbers
(0 or 1) with the 10-key pad.
3. Select A mode with [
] and [
¯
] keys.
4. Enter the adjustment value with the 10-key pad.
5. Press the [EXECUTE] key.
The value entered in procedure 4 is set.
The finisher’s jogger starts operation. During operation, the
[EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed while it is highlighted, the
load operation is interrupted.
[EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed while it is highlighted, the
load operation is interrupted.
4
4 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors
in the paper feed section (desk feed, large capacity
tray) and the related circuit.
in the paper feed section (desk feed, large capacity
tray) and the related circuit.
Section
Paper transport
Item
Operation
Operation/
Procedure
Procedure
The operting conditions of the sensors and detectors in
the paper feed section are displayed.
The active sensors and detectors are highlighted.
the paper feed section are displayed.
The active sensors and detectors are highlighted.
Desk Unit Sensor
DDOPSW
Door open sensor
DPOD1
Paper exit transport sensor 1cs
DPOD2
Paper exit transport sensor 2 cs
DPOD3
Paper transport sensor 3cs
DLUD1
1cs Lift upper limit sensor
DPED1
1cs Paper empty sensor
DCSPD1
1cs remaining quantity detection 1
DLUD2
2xs lift upper limit sensor
DPED2
2cs paper empty sensor
DCSPD2
2cs remaining quantity detection 1
DLUD3
3cs lift upper limit sensor
DPED3
3cs paper empty sensor
DCSPD3
3cs remaining quantity detection 1
FOUND1
1cs lift unit detection (Installation detection)
FOUND2
2cs lift unit detection (Installation detection)
FOUND3
3cs lift unit detection (Installation detection)
DCSS11
1cs size detection 0
DCSS12
1cs size detection 1
DCSS13
1cs size detection 2
DCSS14
1cs size detection 3
DCSS21
2cs size detection 0
DCSS22
2cs size detection 1
DCSS23
2cs size detection 2
DCSS24
2cs size detection 3
DCSS31
3cs size detection 0
DCSS32
3cs size detection 1
DCSS33
3cs size detection 2
DCSS34
3cs size detection 3
LCC Unit Sensor
LRE
Remaining quantity sensor
LUD
Upper limit sensor
LDD
Lower limit sensor
LPED
Paper empty sensor
LPFD
Paper exit sensor
LDSW
Door open SW
LTOD
Body connection sensor
LCD
Cassette detection line
4 - 3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the loads in the paper
feed section (desk paper feed, large capacity tray) and
the control circuits.
feed section (desk paper feed, large capacity tray) and
the control circuits.
Section
Paper transport
Item
Operation
Operation/
Procedure
Procedure
1. The names of the loads which can be operated are
displayed.
Select the load to be checked with the key, and the
selected load is highlighted.
Select the load to be checked with the key, and the
selected load is highlighted.
2. Press the [EXECUTE] key.
The load selected in procedure 1 starts the operation.
AR-505
8/6/1999
7 – 10
During the operation of the load, the [EXECUTE] key is high-
lighted. If the [EXECUTE] key is pressed while it is highlighted, the
operation is stopped.
lighted. If the [EXECUTE] key is pressed while it is highlighted, the
operation is stopped.
Desk Unit Output
DM
Transport motor
DLUM1
Lift up motor 1
DLUM2
Lift up motor 2
DLUM3
Lift up motor 3
DPFS1
Paper feed solenoid 1
DPFS2
Paper feed solenoid 2
DPFS3
Paper feed solenoid 3
DPFC1
Paper feed clutch 1
DPFC2
Paper feed clutch 2
DPFC3
Paper feed clutch 3
DTRC
Transport clutch
Lcc Unit Output
LLED
Dorr open LED
LPFC
Paper feed clutch
LPFS
Paper feed solenoid
LPFM
Transport motor
LLM
Lift motor
The LCC unit lit motor continues lifting up and falling down
5
5 - 1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the display, LCD in the
operation panel, and control circuit.
operation panel, and control circuit.
Section
Operation
(Display/Operation key)
(Display/Operation key)
Item
Operation
Operation/
Procedure
Procedure
The LCD shows the following message.
(The contrast changes in the sequence of Current level
(The contrast changes in the sequence of Current level
®
MAX
®
MIN
®
Current level
®
MAX
®
MIN in
every 2sec.)
During that period, each LED is lighted for 2sec.
¯
2.0sec.
5 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the heater lamp and the
control circuit.
control circuit.
Section
Fixing (Fusing)
Item
Operation
Operation/
Procedure
Procedure
1. Select the lamp to be checked with the key.
2. Press the [EXECUTE] key.
The selected heater lamp repeats ON/OFF in the
frequency of 500msec 5 times.
frequency of 500msec 5 times.
Then the [EXECUTE] key returns to the original dis-
play.
play.
When the [EXECUTE] key is pressed during
ON/OFF operation of the heater lamp, the heater
lamp is turned OFF and the [EXECUTE] key returns
to the original display.
ON/OFF operation of the heater lamp, the heater
lamp is turned OFF and the [EXECUTE] key returns
to the original display.
HL1 (LEFT): This lamp is on the left when viewed from the front
and it heats the center of the lamp.
HL2 (RIGHT): This lamp is on the right when viewed from the
front and it heats both ends of the lamp.
5 - 3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the copy lamp and the
control circuit.
control circuit.
AR-505
7 – 11
8/6/1999
Click on the first or last page to see other AR-505 (serv.man9) service manuals if exist.