Sharp AR-505 (serv.man9) Service Manual ▷ View online
While the load is operated, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed under this state, the load opera-
tion is interrupted.
tion is interrupted.
DTC1
Duplex unit paper entry transport clutch 1
DTC2
Duplex unit paper entry transport clutch 2
DSCS
Duplex unit roller contact solenoid
9 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors
in the duplex section and the control circuit.
in the duplex section and the control circuit.
Section
Duplex
Item
Operation
Operation/
Procedure
Procedure
The operations of sensors and detectors in the duplex
section are displayed.
section are displayed.
The active sensors and detectors are highlighted.
DSBD
Duplex unit paper entry switchback section sensor
DPPD1
Duplex unit paper transport switch 1
DPPD2
Duplex unit paper transport switch 2
DPPD3
Duplex unit paper transport switch 3
DPAD
Duplex unit alignment plate home sensor
9 - 4
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the duplex unit align-
ment plate and its control circuit.
ment plate and its control circuit.
Section
Duplex
Item
Operation
Operation/
Procedure
Procedure
1. Select the paper size.
The selected paper size is highlighted.
2. Press the [EXECUTE] key.
Alignment operation is continuously operated.
During the operation, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed under this state, the operation is
interrupted.
interrupted.
10
10 - 0
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the toner motor and its
control circuit.
control circuit.
(Note) Do not execute this simulation with toner in the
toner hopper. If executed, excessive toner may
enter the developing section, causing an
overtoner trouble. Be sure to remove the toner
motor from the toner hopper before executing
this simulation.
enter the developing section, causing an
overtoner trouble. Be sure to remove the toner
motor from the toner hopper before executing
this simulation.
Section
Image process
(Photoconductor/Develop
ing/Transfer/Cleaning)
(Photoconductor/Develop
ing/Transfer/Cleaning)
Developer/Toner Hopper
Item
Operation
Operation/
Procedure
Procedure
When the [EXECUTE] key is pressed, it is highlighted
and the toner motor rotates for 10 sec.
and the toner motor rotates for 10 sec.
After 10sec of rotation, the toner motor stops and the [EXECUTE]
key returns to the normal display.
If the [EXECUTE] key is pressed during rotation, the toner motor is
stopped and the [EXECUTE] key returns to the normal state.
key returns to the normal display.
If the [EXECUTE] key is pressed during rotation, the toner motor is
stopped and the [EXECUTE] key returns to the normal state.
13
13 - 0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self diag U1 trouble.
Item
Trouble
Operation/
Procedure
Procedure
When the [EXECUTE] key is pressed, the U1 trouble is
canceled and the display returns to the simulation main
code entry screen.
After this simulation is canceled, the machine resumes
operation.
canceled and the display returns to the simulation main
code entry screen.
After this simulation is canceled, the machine resumes
operation.
14
14 - 0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self diag U1/LOC/U2/PF troubles.
AR-505
8/6/1999
7 – 16
Item
Trouble
Error
Operation/
Procedure
Procedure
When the [EXECUTE] key is pressed, the troubles ex-
cluding U1/LCC/U2/PF are canceled and the display re-
turns to the simulation main code entry screen.
After this simulation is canceled, the machine resumes
operation.
cluding U1/LCC/U2/PF are canceled and the display re-
turns to the simulation main code entry screen.
After this simulation is canceled, the machine resumes
operation.
15
15 - 0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self diag U4 - 09/20/21/22 (large ca-
pacity tray) trouble.
pacity tray) trouble.
Section
Paper transport
Item
Trouble
Operation/
Procedure
Procedure
When the [EXECUTE] key is pressed, the U6
(09/20/21/22) (LCC) trouble is canceled and the display
returns to the simulation main code entry screen.
After canceling this simulation, the machine resumes
operation.
(09/20/21/22) (LCC) trouble is canceled and the display
returns to the simulation main code entry screen.
After canceling this simulation, the machine resumes
operation.
16
16 - 0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self diag U2 trouble.
Item
Trouble
Error
Operation/
Procedure
Procedure
When the [EXECUTE] key is pressed, the U2 trouble is
canceled and the display returns to the simulation main
code entry screen.
After this simulation is canceled, the machine resumes
operation.
canceled and the display returns to the simulation main
code entry screen.
After this simulation is canceled, the machine resumes
operation.
17
17 - 0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel copy inhibition by the host computer
during the self diag PF.
during the self diag PF.
Section
Communication unit (TEL/LIU/MODEM etc.)
Item
Trouble
Error
Operation/
Procedure
Procedure
When the [EXECUTE] key is pressed, the PF trouble is
canceled and the display returns to the simulation main
code entry screen. After this simulation is canceled, the
machine resumes operation.
canceled and the display returns to the simulation main
code entry screen. After this simulation is canceled, the
machine resumes operation.
21
21 - 1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the maintenance cycle.
Item
Specifications
Counter
Operation/
Procedure
Procedure
When the maintenance cycle is selected with the key,
the selected key is highlighted. The maintenance mes-
sage is displayed in every selected cycle. When FREE
is selected, the maintenance display is not shown.
the selected key is highlighted. The maintenance mes-
sage is displayed in every selected cycle. When FREE
is selected, the maintenance display is not shown.
(AR-2XX/3XX series)
(AR-4XX series)
(AR-501/505)
AR-505
7 – 17
8/6/1999
22
22 - 1
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the print out count of each section in
each operation mode.
(Used to check the maintenance timing.)
each operation mode.
(Used to check the maintenance timing.)
Item
Counter
Operation/
Procedure
Procedure
FAXandPDA/ZRare only for Japan models.
nnnnnnnn : Counter value
22 - 2
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the total numbers of misfeed and trou-
bles. (When the number of misfeed is considerably
great, it is judged as necessary for repair. The misfeed
rate is obtained by dividing this count value with the to-
tal counter value.)
bles. (When the number of misfeed is considerably
great, it is judged as necessary for repair. The misfeed
rate is obtained by dividing this count value with the to-
tal counter value.)
Item
Mis-feed
Operation/
Procedure
Procedure
MACHINE JAM:The number of paper jam troubles
occurred in the sections other than the
document feeders (SPF/ADF/RADF).
document feeders (SPF/ADF/RADF).
DF JAM:
The number of paper jam troubles
occurred in the document feeders
(SPF/ADF/RADF).
occurred in the document feeders
(SPF/ADF/RADF).
TROUBLE:
Total number of troubles
nnnnnnnn : Counter value
22 - 3
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the misfeed positions and the number of
misfeed in each position. (If the number of misfeed is
considerably great, it can be judged as necessary for
repair.) (Sections other than ADF/RADF/SPF sections)
misfeed in each position. (If the number of misfeed is
considerably great, it can be judged as necessary for
repair.) (Sections other than ADF/RADF/SPF sections)
Item
Mis-feed
Operation/
Procedure
Procedure
The misfeed history sections indicated by the sensors
and detectors are displayed sequentially from the latest
one. Max. 40 items of information can be stored, and
the oldest one is deleted sequentially.
The trouble position may be presumed with this data.
and detectors are displayed sequentially from the latest
one. Max. 40 items of information can be stored, and
the oldest one is deleted sequentially.
The trouble position may be presumed with this data.
22 - 4
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the total trouble (self diag) history.
Item
Mis-feed
Operation/
Procedure
Procedure
The trouble history error codes are displayed sequen-
tially from the latest one. Max. 40 items of information
can be stored, and the oldest one is deleted sequen-
tially. The machine condition can be presumed accord-
ing to this data.
tially from the latest one. Max. 40 items of information
can be stored, and the oldest one is deleted sequen-
tially. The machine condition can be presumed accord-
ing to this data.
22 - 5
Purpose
Others
Function
(Purpose)
(Purpose)
Used to check the ROM version of each unit (section).
Item
Software
Operation/
Procedure
Procedure
The ROM version of each section can be checked.
If there is any problem in the software, check the ROM
version of each section with this simulation and replace
with a new version if necessary.
FAX is for Japan model only.
If there is any problem in the software, check the ROM
version of each section with this simulation and replace
with a new version if necessary.
FAX is for Japan model only.
AR-505
8/6/1999
7 – 18
22 - 6
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to output the list of the setting and adjustment
data (simulations, FAX soft switch, counters).
data (simulations, FAX soft switch, counters).
Item
Data
Adjust/Setting data
Operation/
Procedure
Procedure
When installing or servicing, execute this simulation to
print and store the adjustment values and setting data
for use in the next servicing. (Memory trouble, PWB re-
placement, etc.)
print and store the adjustment values and setting data
for use in the next servicing. (Memory trouble, PWB re-
placement, etc.)
In this case, the print conditions can be set optionally.
1. Select the setup item.
(The selected item is highlighted.)
2. Set the item and conditions with the 10-key pad.
3. Press the [EXECUTE] key to print various data.
A: Print out items (Contents)
1: All adjustment values and setup data
2: All counter data
3: FAX soft switch setup data (Japan only)
4: Print density adjustment data
5: Adjustment and setup data of the other simulations
1: All adjustment values and setup data
2: All counter data
3: FAX soft switch setup data (Japan only)
4: Print density adjustment data
5: Adjustment and setup data of the other simulations
B: Paper feed mode
1: Manual paper feed
2: Upper paper feed tray
3: Lower paper feed tray
4: Desk upper paper feed tray
5: Desk middle paper feed tray
6: Desk lower paper feed tray
7: Large capacity paper feed tray
1: Manual paper feed
2: Upper paper feed tray
3: Lower paper feed tray
4: Desk upper paper feed tray
5: Desk middle paper feed tray
6: Desk lower paper feed tray
7: Large capacity paper feed tray
22 - 7
Purpose
User data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to display the key operator code. (This simulation
is used when the customer forgets the key operator
code.)
is used when the customer forgets the key operator
code.)
Item
Data
User data
Operation/
Procedure
Procedure
nnnnn : Key operator code
22 - 8
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the number of use of the staple, the
ADF, RADF, SPF, and scanning.
ADF, RADF, SPF, and scanning.
Item
Counter
Operation/
Procedure
Procedure
This data is used to check the use frequency of each
section. According to this data, maintenance is exe-
cuted.
section. According to this data, maintenance is exe-
cuted.
nnnnnnnn : Counter value
22 - 9
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the number of use of each paper feed
section. (the number of prints)
section. (the number of prints)
Section
Paper transport
Item
Counter
Operation/
Procedure
Procedure
This data is used to check the use frequency of each
paper feed section, According to this data, mainte-
nance is performed.
paper feed section, According to this data, mainte-
nance is performed.
nnnnnnnn : Counter vlaue
22 - 10
Purpose
Operation data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to check the system configuration (option, internal
hardware).
hardware).
Item
Specifications
Options
Operation/
Procedure
Procedure
This simulation allows to check the system configura-
tion.
The devices and the option units which are installed are
displayed with the model names or size, etc.
tion.
The devices and the option units which are installed are
displayed with the model names or size, etc.
(AR-230/280/285 series)
AR-505
7 – 19
8/6/1999
Click on the first or last page to see other AR-505 (serv.man9) service manuals if exist.