DOWNLOAD Sharp AR-505 (serv.man9) Service Manual ↓ Size: 1.06 MB | Pages: 51 in PDF or view online for FREE

Enter the code number with the 10-key pad and press the [OK]
key.

∗

Detection size when 8.5" x 13" document/paper is used

Unit

Destination

Set value

0

(Default)

(Invalid)

1 (Valid)

Document AR-SP1

All
destinations

8.5" x 14" 8.5" x 13" *1

AR-AF1
AR-RF1

Japan

A4R

A4R

*5

EX AB
series
(SLK/SEEG)

A4R

A4R

*5

EX AB
series
(SCA/
Others)

A4R

8.5" x 13" *3

Inch series
(SEC/SECL)

8.5" x 14" 8.5" x 14" *5

Inch series
(Others)

8.5" x 14" 8.5" x 13" *1

Document
table

Japan/EX
AB series

B4

8.5" x 13" *2

Inch series

8.5" x 14" 8.5" x 13" *1

Paper

Main
body

Manual
feed
tray

All
destinations

8.5" x 14" 8.5" x 13" *4

Paper
feed
cassette

All
destinations

        —      *6

AR-DE1/DE2

All
destinations

AR-LC1

All
destinations

—

*1: A document of 8.5" x 14" is detected as 8.5" x 13".

*2: A document of B4 is detected as 8.5" x 13".

*3: A document of A4R is detected as 8.5" x 13".

*4: A document of 8.5" x 14" is detected as 8.5" x 13".

*5: Applicable by replacing the document set tray of the AR-

AF1/RF1.

*6: Setting is available with the key operator program (P40).

Value

Display

Paper

1

Characters

HEAVY PAPER

PLAIN PAPER

2

Weight in g.

106 - 200 g/m

2

56 - 105 g/m

2

3

Weight in lbs.

28+ - 55 lbs

15 - 28 lbs

Purpose

Setting

Function
(Purpose)

Used to set the specifications of the auditor. Setting
must be made depending on the use condition of the
auditor.

Section

Auditor

Item

Specifications

Operation/
Procedure

Enter the code number corresponding to the auditor
specification mode with the 10-key pad and press the
[OK] key.

Set value 

Specification mode 

1

Built-in auditor mode (Default)

2

Coin vendor 

3

Others 

Purpose

Setting

Function
(Purpose)

Used to set the count mode of the total counter and the
maintenance counter.

Item

Specifications

Counter

Operation/
Procedure

Used to set the single count-up or double count-up for
the total counter, the maintenance counter, and the de-
veloper counter when printing is performed with A3, 11
x 17" paper,

1. Select the kind of the counter with [

↑

] and [

↓

] key.

A

Total

B

Maintenance

C

Developer

2. Enter "1" or "2" with the 10-key pad and press the [OK] key.

1: Single count

2:  Double count

Default: 2

Purpose

Setting

Function
(Purpose)

Used to set the specifications depending on the desti-
nation.

Item

Specifications the
destination

Destination

Operation/
Procedure

Select the destination referring to the table below.

U.S.A.

United States of America

Canada

Canada

Inch

Inch series, other destinations

Japan

Japan

AB_B

AB series (B5 detection) other destinations

Europe

Europe

U.K.

United Kingdom

Aus.

Austrailia

AB_A

AB series (A5 detection) other destinations

When the destination setting is changed, the following specifica-
tion is changed.
(Toner save mode setup specification) (Paper specification)

AR-505

10/8/1999

7 – 24

Purpose

Setting

Function
(Purpose)

Used to set the fusing operation mode (paper curl cor-
responding mode).

Section

Fixing (Fusing)

Item

Operation

Operation/
Procedure

Due to the paper type (paper property), paper may be
curled in the fusing section and cause a paper jam. To
prevent against this, the fusing condition is changed.

Enter the code number corresponding to the fusing condition and
press the [OK] key. 

Set value 

Remedy mode

Fusing condition

0

Normal operation 

(Default)

1

Remedy mode 1

a. Racing until the specified

fusing temperature is
reached.

2

Remedy mode 1

a. Racing is performed until

the specified fusing
temperature is reached.

b. Copy mode is duplex mode

or sort.

Group mode 

•

Previous rotation is made
for 5 sec before starting
copying.

Purpose

Setting

Function
(Purpose)

Used to set VALID/INVALID of toner save operation.
(This simulation is valid only in the Japan and UK ver-
sions. (It depends on SIM 26-6 (Destination setting).
For the other destinations, the same setting can be
executed with the user program.)

Item

Specifications

Operation mode
(Common)

Operation/
Procedure

Enter the code number corresponding to the condition
(the toner save YES/NO) with the 10-key and press the
[OK] key.

Set value 

Toner save 

0

YES 

1

NO (Default)

Purpose

Setting

Function
(Purpose)

Used to set the specification (language display) for the
destination. (Target models: AR-280/285/335) (Exclud-
ing the Japan models.)

Item

Specifications

Operation/
Procedure

Select the language to be used according to the table
below. 

Display Language 

ENG.(US)

English(US)

ENG.(UK)

English(UK)

FRENCH

French 

SPANISH

Spanish 

GERMAN

German 

Purpose

Setting

Function
(Purpose)

Used to set the CE mark conforming operation mode.
(For flickers when driving the fusing heater lamp.)

Item

Specifications

Operation mode
(Common)

Operation/
Procedure

Enter the number corresponding to the operation mode
with the 10-key and press the [OK] key.

Set value 

Content 

0

CE mark control inhibit 

1

CE mark control allowed (Default)

0:  Normal operation heater lamp slow up control

1: CE mark standard complying operation (Heater lamp slow up

control) (Europe)

Purpose

Setting

Function
(Purpose)

Used to set whether the trouble history display of SIM
22-4 is displayed as one trouble or as the number of
continuous troubles when two or more troubles of a
same kind occured.

Item

Specifications

AR-505

7 – 25

10/8/1999

Operation/
Procedure

Used to set whether the trouble history display by SIM
22-4 is displayed as one trouble or as the accumulated
number of continuous troubles when two or more trou-
bles of same kind occur continuously.

Select the number corresponding to the display mode with the 10-
key and press the [OK] key.

1: The trouble history display by SIM 22-4 is displayed as it is

when two or more troubles occur continuously.

0: The trouble history display by SIM 22-4 is displayed as one

trouble when two or more troubles occur continuously.

Default: 0

Purpose

Setting

Function
(Purpose)

Used to set the ICU fan operating temperature. (Opera-
tion in pre-heat mode.) (Excluding Japan models.)

Section

ICU

Item

Operation

Operation/
Procedure

Used to set the threshold value of the ambient tem-
perature for turning ON the ICU fan motor in the pre-
heat mode.

Set range : 0~33[°C]

Default : 30[°C] (30)

Enter the operating temperature with the 10-key pad
and press the [OK] key.

Purpose

Setting

Function
(Purpose)

Polygon motor stop mode setup (AR-501/505)
Used to set the stop time of the polygon motor after
leaving in ready state and to set Enable/Disable of the
setting. (Other models)

Item

Specifications

Operation/
Procedure

(AR-501/505)
When this simulation is executed, the current set value
is displayed.

At that time, the set value can be changed with the 10-key.
When the OK key is pressed, the currently set value is stored in
the EEPROM.
Default: 0

0

Normal mode

Control according to the setup in the
silent mode by the user setup.

1

Silent mode

After completion of a job, the polygon
motor is stopped in the time set in the
silent mode of the user setup.

(Other models)
A
1. Used to set the time (minute) to stop the polygon motor with

the 10-key.
(Regardless of setting in B, the time can be freely set.)

2. Press the OK key to store the set time.

3. Press the CA key to reset. Only when B is set to "1: YES", the

polygon motor is stopped in the set time.
Set range: 1-30 min
Default: 30 min

B Used to set YES/NO of the setup of A.

Default: 0 (NO)

Set value

Content

0

NO (The currently set operation is performed.)  

→

SP/FP does not stop.
40 NEW Stops in the default time (30 min).

1

Stops in the set value of A.

Purpose

Setting

Function
(Purpose)

Used to enable/disable the auto magnification ratio se-
lect (AMS) function in the pamphlet copy mode.

Item

Specifications

Operation mode
(Common)

Operation/
Procedure

This simulation is used to enable or disable the auto-
matic magnification ratio selection (AMS) in the pam-
phlet mode.

Set value

Set content

0

Automatic magnification ratio selection (AMS) is
enabled. 

1

Automatic magnification ratio selection (AMS) is
disabled. 

Purpose

Setting

Function
(Purpose)

Used to set the model of the unit which is connected to
the SCSI I/F of ICU PWB.

Section

ICU

Item

Specifications

Interface/Communication

AR-505

10/8/1999

7 – 26

Operation/
Procedure

A is at the left of B when viewed from the rear side.

0:  No connection

1:  Printer controller

3:  External printer controller (Not used)

4:  Scanner controller (Not used)

8:  Tandem connection (Initiator)

10: Tandem connection (Target)

One SCSI channel available (Japan only) 

Two SCSI channels available
(AR-501/505)

(Other models)

Purpose

Setting

Function
(Purpose)

Used to set the image direction or not regardless of
modes when the finisher/sorter is installed.

Item

Specifications

Operation mode
(Common)

Operation/
Procedure

This simulation is used to set the image direction or not
regardless of modes when the finisher/sorter is in-
stalled. (Other models than AR-501/505)

Set value

Set content

0

Not set. (The image direction is changed in the
staple mode of FN1

∗

.)

1

Set. (The image direction is not changed
regardless of presence of the staple.)

Default: 0

Purpose

Setting

Function
(Purpose)

Used to set YES/NO of black/white reversion is al-
lowed.

Item

Specifications

Operation/
Procedure

When this simulation is executed, the current set value
is displayed.
At that time, the set value can be changed with the 10-
key.

When the OK key is pressed, the currently set value is stored in
the EEPROM.

Default: 1 (YES) (Black/white reversion is allowed.)

0

NO: Black/white reversion is inhibited.

1

YES: Black/white reversion is allowd.

Function
(Purpose)

Used to set whether white paper discharge count up is
performed or not.
("White paper" means insertion paper in the OHP inser-
tion paper mode (without copy), cover paper in the
cover paper insertion mode (without copy)/back cover,
and white paper in the duplex exit mode (CA etc.).)

Operation/
Procedure

When this simulation is executed, the current set value
is displayed.
Under this state, the set value can be changed with the
10-key.

When the OK key is pressed, the currently set value is stored in
the EEPROM. 

Set value

Content

A

0

White paper count up is not performed.

1

White paper count up is performed.

Destination Default

U.K./Europe/Aus.

0 (Count up is not performed.)

Others

1 (Count up is performed.)

When set to 0 (count up is nor performed), the following counters
do not count up. 

•

COPIES counter

•

Total counter

•

Maintenance counter

•

Developer counter

•

Department management counter

•

The signal (PNC) for the external auditor (mechanism counter)
is not outputted. 

AR-505

7 – 27

10/8/1999