Sharp AL-2020 (serv.man5) User Manual / Operation Manual ▷ View online
51
5
REDUCTION/ENLARGEMENT/ZOOM
Three preset reduction ratios and two enlargement ratios can be selected. The zoom
function enables copy ratio selection from 25% to 400% in 1% increments. (When
the SPF is being used, the zoom copy ratio range is 50% to 200%.)
function enables copy ratio selection from 25% to 400% in 1% increments. (When
the SPF is being used, the zoom copy ratio range is 50% to 200%.)
1
Set the original and check the paper size.
2
Use the copy ratio selector key and/or ZOOM (
,
) keys to
select the desired copy ratio.
3
Set the reduction/enlargement ratio.
To select a preset copy ratio:
Preset reduction and enlargement ratios are:
50%, 70%, 86%, 129%, and 200%.
Preset reduction and enlargement ratios are:
50%, 70%, 86%, 129%, and 200%.
To select a zoom ratio:
When a ZOOM (
When a ZOOM (
or
) key is pressed, the
ZOOM indicator will light up and the zoom ratio will
be displayed in the display.
be displayed in the display.
SELECTING THE PAPER TRAY
Press the tray select (
) key.
Each time you press the tray select (
) key, the location
indicated by the paper feed location indicator changes in
the following order: paper tray, multi-bypass tray.
the following order: paper tray, multi-bypass tray.
• To verify a zoom setting without changing the zoom ratio,
press and hold down the copy ratio display (%) key. When the
key is released, the display will return to the copy quantity
display.
key is released, the display will return to the copy quantity
display.
• To reset the ratio to 100%, press the copy ratio selector key
repeatedly until the 100% indicator lights up.
To decrease or increase the zoom ratio rapidly, press and hold
down the ZOOM (
down the ZOOM (
) or (
) key. However the value will stop
at the preset reduction or enlargement ratios. To move beyond
these ratios, release the key and then press and hold it down
again.
these ratios, release the key and then press and hold it down
again.
A5
A4
A4
B5
A4
A5
141
86
70
A4
B5
A5
A5
A5
A4
A4
B5
A4
A5
141
86
70
52
This chapter describes the special functions of this unit. Use these functions as
needed.
needed.
TWO SIDED COPYING
When copying from the SPF, two-side originals can be copied automatically without
having to manually turn them over. Automatic two-sided copying can also be
performed without using the SPF. When copying from one-sided originals to two-
sided copies, copying orientation can be selected between Turn on Long Edge and
Turn on Short Edge.
having to manually turn them over. Automatic two-sided copying can also be
performed without using the SPF. When copying from one-sided originals to two-
sided copies, copying orientation can be selected between Turn on Long Edge and
Turn on Short Edge.
• When making two-sided copies from the original table, the paper size
must be A4, letter. When making two-sided copies from the
SPF (AL-2040), A4, B5, A5, letter, legal, and invoice sizes can be
used. Non-standard size paper cannot be used.
SPF (AL-2040), A4, B5, A5, letter, legal, and invoice sizes can be
used. Non-standard size paper cannot be used.
• When making two-sided copies, the multi-bypass tray cannot be used.
• When using two-sided invoice size originals from the SPF (AL-2040),
• When using two-sided invoice size originals from the SPF (AL-2040),
be sure to place them in the landscape orientation. Otherwise, an
original misfeed will occur.
original misfeed will occur.
A
A
A
A A
A
A
A A
Turn on Short Edge
Turn on Long Edge
6
SPECIAL FUNCTIONS
53
6
Making two-sided copies
1
Place the original(s) on the document glass or in the SPF. (see
"ORIGINAL PLACEMENT" (p.47).
"ORIGINAL PLACEMENT" (p.47).
2
Select two-sided copy mode.
When copying in a one-sided to two-sided mode:
Use the original to copy key to select the desired one-sided to two-sided
copying mode (Turn on Long Edge or Turn on Short Edge). See the
illustrations on page 52.
Use the original to copy key to select the desired one-sided to two-sided
copying mode (Turn on Long Edge or Turn on Short Edge). See the
illustrations on page 52.
3
Select the copy settings. See "SET THE COPY QUANTITY"
(p.49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p.49),
and "REDUCTION/ENLARGEMENT/ZOOM" (p.51).
(p.49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p.49),
and "REDUCTION/ENLARGEMENT/ZOOM" (p.51).
Using the document glass
1
Press the start (
) key.
The original is scanned into the unit's memory and the number of the
copy quantity blinks in the display.
copy quantity blinks in the display.
2
Place the original that you wish to copy onto the rear side of the
paper, and press the start (
paper, and press the start (
) key again.
Copying begins.
Using the SPF (AL-2040)
Press the start (
Press the start (
) key. Copying begins in the selected two-sided copy mode.
54
DESCRIPTION OF OTHER SPECIAL FUNCTIONS
Toner save mode
Reduces toner consumption by approximately 10%.
Power save modes
The unit has two power save modes of operation: preheat mode and auto power
shut-off mode.
shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save (
) indicator will light up
and other indicators will remain on or off as before. In this condition, the fuser in
the unit is maintained at a lower heat level, thereby saving power. To copy from
the preheat mode, make desired copier selections and press the start (
the unit is maintained at a lower heat level, thereby saving power. To copy from
the preheat mode, make desired copier selections and press the start (
) key
using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power save (
) indicator
will light up and other indicators except the ONLINE indicator will go out. The auto
power shut-off mode saves more power than the preheat mode but requires a
longer time before starting copying. To copy from the auto power shut-off mode,
press the start (
power shut-off mode saves more power than the preheat mode but requires a
longer time before starting copying. To copy from the auto power shut-off mode,
press the start (
) key. Then make desired copier selections and press the start
(
) key using the normal copying procedure.
Auto clear
The unit returns to the initial settings a preset amount of time after the end of job.
This preset amount of time (auto clear time) can be changed.
This preset amount of time (auto clear time) can be changed.
Resolution of AUTO & MANUAL mode
You can set the copy resolution used for AUTO and MANUAL (
) exposure mode.
Prevention of OC copies when the SPF is up function (AL-2040)
When enabled, this function may help prevent wasteful use of toner that occurs
when the OC cover is not completely closed.
If the start (
when the OC cover is not completely closed.
If the start (
) key is pressed when the OC cover is not completely closed, "
"
will appear in the display and copying may not take place. If copying does not take
place, copying can be performed by pressing the start (
place, copying can be performed by pressing the start (
) key again, however, the
scan size set in "Copy effective paper width setting function" (program numbers 25,
26) will be used.
If the OC cover is completely closed after "
26) will be used.
If the OC cover is completely closed after "
" appears, copying will take place at
the normal size.
TONER SAVE MODE
1
Press the exposure mode selector key
to select the MANUAL (
to select the MANUAL (
) mode.
2
Press and hold down the exposure mode
selector key for approximately 5 seconds.
The MANUAL (
selector key for approximately 5 seconds.
The MANUAL (
) indicator will go out
and the PHOTO (
) indicator will begin
to blink. The light and dark indicator
marked "5" will light up, indicating the
standard toner mode is active.
marked "5" will light up, indicating the
standard toner mode is active.
Click on the first or last page to see other AL-2020 (serv.man5) service manuals if exist.