Sharp AL-2020 (serv.man5) User Manual / Operation Manual ▷ View online
55
6
3
To enter the toner save mode, press the
light (
light (
) key. The light and dark
indicator marked "1" will light up,
indicating the toner save mode is
selected.
indicating the toner save mode is
selected.
4
Press the exposure mode selector key. The PHOTO (
) indicator
will stop blinking and light up steadily. The light and dark indicator
marked "3" will light up. The toner save mode is now active.
marked "3" will light up. The toner save mode is now active.
USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or
canceled as desired.
canceled as desired.
Setting the user programs
1
Press and hold down the light (
) key for more than 5
seconds until all the alarm indicators (
,
,
) blink and
"
" appears in the display.
2
Use the left copy quantity (
) key to select a user program
number (For the user program numbers, see the following table.).
The selected number will blink in the left side of the display.
The selected number will blink in the left side of the display.
3
Press the start (
) key. The entered program number will be
steadily lit and the currently selected parameter number for the
program will blink on the right side of the display.
program will blink on the right side of the display.
4
Select the desired parameter using the right copy quantity (
) key.
The entered parameter number will blink on the right of the display.
To return to the standard mode, repeat the procedure but use the dark
(
(
) key to select exposure level "5" in step 3.
Program
No.
Mode
Parameters
1
Auto clear time
1
10 sec., 2
30 sec., *3
60 sec.,
4
90 sec., 5
120 sec., 6
OFF
2
Preheat mode
*1
30 sec., 2
60 sec., 3
5 min.,
4
30 min., 5
60 min., 6
120 min.,
7
240
min.
3
Auto power shut- off
mode
mode
*1
ON, 2
OFF
4
Auto power shut- off
timer
timer
*1
5 min., 2
30min., 3
60 min.,
4
120 min., 5
240 min.
56
* Factory default settings are indicated with an asterisk (*).
5
Press the start (
) key. The right-hand number in the display
will be steadily lit and the entered value will be stored.
6
Press the light (
) key to return to the normal copy mode.
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
Press and hold down the clear key for approximately 5 seconds. The
total number of copies will appear in two steps, each with three digits.
Example: Total number of copies is 1,234.
total number of copies will appear in two steps, each with three digits.
Example: Total number of copies is 1,234.
6
SPF automatic
original discharge
time (AL-2040)
original discharge
time (AL-2040)
1
5 min., *2
30 min.,
3
60 min., 4
120 min.,
5
240 min., 6
OFF
10
Resolution of AUTO
& MANUAL mode
& MANUAL mode
*1
300dpi, 2
600dpi
21
Reset factory
1
YES, *2
NO
24
Prevention of OC
copies when the
SPF is up function
copies when the
SPF is up function
*1
ON, 2
OFF
25
Copy effective paper
width setting function
(Bypass tray)
width setting function
(Bypass tray)
*1
Large (A4 width),
2
Small (B5R width)
26
Copy effective paper
width setting function
width setting function
*1
Large (A4 width),
2
Small (B5R width)
28
Selection of copy
start state (Polygon
rotation on/off)
start state (Polygon
rotation on/off)
*1
ON, 2
OFF
29
Fusing temperature
setting when the
bypass tray is used
setting when the
bypass tray is used
1
Low, *2
High
To change the setting or to set another mode, press the clear
key. The unit will return to step 2.
key. The unit will return to step 2.
Program
No.
Mode
Parameters
7
57
This chapter describes how to replace the TD cartridge and drum cartridge and how
to clean the unit.
to clean the unit.
TD CARTRIDGE REPLACEMENT
The TD cartridge replacement required (
) indicator will light up when toner is
needed. For more information on purchasing the TD cartridge, see "ABOUT
SUPPLIES AND OPTIONS" (p.72). If copying is continued while the indicator is lit,
copies will gradually become lighter until the unit stops and the indicator begins
blinking. Replace the old TD cartridge by following the procedure below.
SUPPLIES AND OPTIONS" (p.72). If copying is continued while the indicator is lit,
copies will gradually become lighter until the unit stops and the indicator begins
blinking. Replace the old TD cartridge by following the procedure below.
1
Open the multi-bypass tray, side cover, and front cover, in that
order.
order.
To open the multi-bypass tray, see "The multi-bypass tray" (p.17). To open
the side cover and front cover, see "INSTALLING THE TD CARTRIDGE"
(p.10).
the side cover and front cover, see "INSTALLING THE TD CARTRIDGE"
(p.10).
2
Gently pull the TD cartridge out
while pressing the lock release
button.
while pressing the lock release
button.
3
Install a new TD cartridge. To install the new cartridge, see
"INSTALLING THE TD CARTRIDGE" (p.10).
"INSTALLING THE TD CARTRIDGE" (p.10).
Be sure to use only genuine SHARP parts and supplies.
• After the unit stops, it may be possible to make a few more copies by taking
the TD cartridge out of the unit, shaking it horizontally, then reinstalling it. If
copying is not possible after this operation, replace the TD cartridge.
copying is not possible after this operation, replace the TD cartridge.
• During long copy run of a dark original, the TD cartridge replacement
required (
) indicator may light up, the start (
) indicator blink,
and the unit stops, even though toner is left. The unit will feed toner up
to 2 minutes and then the start (
to 2 minutes and then the start (
) indicator will light up. Press the
start (
) key to restart copying.
Dispose of the old TD cartridge in accordance with local regulations.
Lock release button
7
MAINTENANCE
58
4
Close the front cover and then the side cover by pressing the
round projections near the side cover open button. The indicator
(
round projections near the side cover open button. The indicator
(
) will go out and the start (
) indicator will light up.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 18,000 copies*. When the internal
counter reaches approximately 17,000 copies, the drum replacement required (
counter reaches approximately 17,000 copies, the drum replacement required (
)
indicator will light up indicating that replacement of the drum cartridge will be needed
soon. For more information on purchasing the drum cartridge, see "ABOUT SUPPLIES
AND OPTIONS" (p.72). When the indicator begins to blink, the unit will stop operating
until the cartridge is replaced. Replace the drum cartridge at this time.
soon. For more information on purchasing the drum cartridge, see "ABOUT SUPPLIES
AND OPTIONS" (p.72). When the indicator begins to blink, the unit will stop operating
until the cartridge is replaced. Replace the drum cartridge at this time.
*Based on copying onto A4 size paper at 5% toned area.
1
Remove the TD cartridge (see step 1 and 2 in "TD CARTRIDGE
REPLACEMENT" (p.57)).
REPLACEMENT" (p.57)).
2
Hold the drum cartridge handle and
gently pull the cartridge out. Dispose
of the old drum cartridge in
accordance with local regulations.
gently pull the cartridge out. Dispose
of the old drum cartridge in
accordance with local regulations.
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
Do not remove the protective cover on the drum portion (black paper) of a new
drum cartridge before use. The cover protects the drum against external light.
drum cartridge before use. The cover protects the drum against external light.
Dispose of the old drum cartridge in accordance with local regulations.
Drum cartridge handle
Click on the first or last page to see other AL-2020 (serv.man5) service manuals if exist.