DOWNLOAD Sharp PN-S525 (serv.man3) Service Manual ↓ Size: 10.19 MB | Pages: 118 in PDF or view online for FREE

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 23

3) You can check, control, and change the monitor’s status and set-

tings by clicking the menu items on the left side of the screen.

•  If you see an [Apply] button next to a setting, click it after you

change that setting.

Note:

• If you click [Refresh] before the screen finishes updating the current

display, the “Server Busy Error” will appear.

Wait for a moment before operating your monitor again.

•  You cannot operate the monitor while it is warming up.

• If “DHCP CLIENT” is set to “ON”, press

on the remote control

unit two times and then check the monitor’s IP address.

■ INFORMATION

Information about this monitor appears.

■ CONTROL

You can control the operations corresponding to the buttons

(

) on the remote control unit. 

Note:

•  In standby mode, Power ON is the operation available.

■ ADJUSTMENT

You can adjust these settings which are also available on the monitor’s

menu.

• SCREEN

• PICTURE

• PICTURE (ADVANCED)

• AUDIO

• SETUP

• OPTION

• SCHEDULE

• ENLARGE

• PIP/PbyP

• FUNCTION

DISPLAY

POWER

 

INPUT

 

SIZE

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 24

■ NETWORK (LAN SETUP)

This screen allows you to set the settings necessary when the monitor

is connected to a LAN.

■ NETWORK (SECURITY)

This screen allows you to specify the security-related settings.

Note:

• The USER NAME and PASSWORD can be up to 8 alphanumeric

characters or symbols.

•  To cancel the user name and/or password after it has been set, make

the box empty and click [Apply].

If your LAN has a DHCP server and you wish to obtain an address
automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.

If the DHCP CLIENT is set to “OFF”, specify an IP address.

If the DHCP CLIENT is set to “OFF”, specify the subnet mask.

If the DHCP CLIENT is set to “OFF”, specify the default gateway.
If you are not using a default gateway, specify “0.0.0.0”.

Specify the DNS server address.
If you are not using a DNS server, specify “0.0.0.0”.

Clicking [Execute] returns all of the LAN SETUP settings to the fac-
tory-preset values except for the DNS SERVER setting.

Sets up a user name and password to restrict access to this monitor.
After entering a user name and password, click [Apply].

You can limit access to this monitor by registering IP addresses of
PCs that should have access.
To limit access, specify the option “From only specific IP addresses”.
Otherwise, to allow access from any PC, specify “All IP Addresses”.

If “ACCEPT IP ADDRESS” is set to “From only specific IP addresses”,
enter the IP addresses that you want to allow.

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 25

■ NETWORK (GENERAL)

This screen allows you to specify the general LAN settings.

Note:

• The MONITOR NAME can be up to 16 alphanumeric characters or

symbols.

■ MAIL (ORIGINATOR)

This screen allows you to configure the e-mail sent periodically or when

the monitor has an error.

The settings depend on the configuration of your LAN. Ask your LAN
administrator for details.

Note:

• You can enter up to 64 alphanumeric characters or symbols for the

ORIGINATOR E-MAIL ADDRESS, ORIGINATOR NAME, ACCOUNT

NAME, and PASSWORD.

•  The SMTP SERVER and POP SERVER can be up to 64 characters.

The following characters can be used: a-z, A-Z, 0-9, - , .

Specify a name for this monitor as it should appear on the Internet
Explorer screen.

Specify the time (in minutes) to elapse before automatically discon-
necting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable this func-
tion.

Specify the TCP port number to use for exchanging data with the
monitor.
Specify a value from 1025 to 65535.

Specify the port number to use when searching for this monitor.
Specify a value from 1025 to 65535.

Specify the SMTP server address for sending e-mail.

*When using a domain name, make sure to specify the DNS server

as well.

Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.

Specify the name for the originator.
This name appears in the “Originator Name” field of the e-mail.

Specify the authentication method to use when sending e-mail.

If the “AUTHENTICATION” method is “POP before SMTP”, specify the
POP server address.

If the “AUTHENTICATION” method is “POP before SMTP”, specify the
account name and password to connect to the POP server.

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 26

■ MAIL (RECIPIENT)

This screen allows you to specify the recipients of the e-mail sent peri-

odically or when the monitor has an error.

Note:

• The RECIPIENT E-MAIL ADDRESSES can be up to 64 alphanu-

meric characters or symbols.

■ MAIL (PERIODICAL)

When PERIODICAL for CONDITION of MAIL (RECIPIENT) is checked,

set the date and time to send the mail.

Caution:

• Do not turn off the main power when you set to send the periodical

mails.

•  Specify the correct date and time.

If the date and time settings are incorrect, the periodical mail is not

sent properly.

•  Regularly confirm that the specified date and time is correct.

Specify the e-mail addresses to send error notification e-mail to.

Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to send the
mails in the PERIODICAL setting.

Sends test e-mail.
This allows you to confirm that the e-mail settings are configured prop-
erly.

When this option is checked, a log is added to the mail which notifies a
temperature or status error.

Specify the day of the week to send the periodical mails.

Specify the time of the day to send the periodical mails.