DOWNLOAD Sharp PN-S525 (serv.man3) Service Manual ↓ Size: 10.19 MB | Pages: 118 in PDF or view online for FREE

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 27

■ SERVICE & SUPPORT (URL INFORMATION)

You can display a specific URL in the URL INFORMATION field on the

INFORMATION screen when an error occurs in the monitor.

Note:

•  It is also possible to specify the message text, such as the name of a

contact or a telephone number, to be displayed instead of the linked

URL.

Enter a URL to display when an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.

Specify the condition to display the URL.

The home page of the specified URL is displayed.
You can check whether the URL you entered is correct.

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 28

Used to display the model name, the manufacturing No., the firmware
version/checksum, the usage time, and Mac address.

MODEL: Model name

S/N : 

Serial 

number

FIRM VERSION (MAIN) 

:  Main firmware version. If the combination

of this version number and the sub 

firmware version number is improper,

“NG” is displayed. 

CHECK SUM (MAIN) 

:  Main firmware check sum

FIRM VERSION (SUB) 

:  Sub firmware version. If the combination

of this version number and the main firm-

ware version number is improper, “NG” is 

displayed. 

CHECK SUM (SUB)

:  Sub firmware check sum

USAGE TIME 

:  Usage time

MAC ADDRESS 

:  MAC address

WHITE BALANCE CHECK : Displayed when the white balance set

value becomes the initial value by
replacement of the PWB or the panel.

(Normally, it is not displayed.)

CALIBRATION CHECK 

: Displayed when the calibration set value

becomes the initial value.
(Normally it is not displayed.)

1)  Press [SIZE] button for 5sec, and press [

1] [ 4 ] [3] [ 2

 

] buttons in 

this sequence. “SERVICE MENU1” is displayed. 

* Immediately after turning on the power, “CALCULATING” is dis-

played for the checksum for a while, and the result is dipslayed. 

• AGING: 

AGING.  Refer to “3-1. AGING”.

• CALIBRATION : 

Used to adjust automatically the gain and the offset of only PC D-sub

and BNC/components/composite. Refer to “3-2. Calibration”.

•  FACTORY RESET : 

Used to reset the user adjustment values, the usage time, and the
operation logs to the factory setting. Refer to “3-3. FACTORY

RESET”.

• MODEL TYPE : 

Used to select the destination. JP : Japanese model, 

EU/US: Except Japanese model, OEM1: Except Japanese OEM

model.

•  HARDWARE CHECK : 

Used to display the hardware detection result. Refer to “3-4. HARD-

WARE CHECK”.

•  WHITE BALANCE SETTING : 

Refer to “3-5. WHITE BALANCE SETTING”.

• COMPONENT PHASE : 

Do not change the setting.

•  AUTO INPUT CHANG DELAY :

Do not change the setting.

•  YBIAS SETTING S-VIDEO :

 Do not change the setting.

•  YBIAS SETTING COMPOSITE : 

Do not change the setting.

•  SIGNAL TUNING : 

Do not change the setting.

1)  With “SERVICE MENU1” displayed, select “SERVICE2” with [

4 ]

button and press [

3] button. 

2)  Select setting item with [ 

2

 

] [ 

4

 

] button.

3)  Adjust it with the [

1] [3] button. 

When the item with => mark press [

3] button and advances to the

next screen. 

4)  Press [MENU] button to return to the previous screen sequentially,

terminating the operation. 

SERVICE1

 

SERVICE2

 

SERVICE MENU1                          1/1

 

MODEL

㧦 PN-S525

12345678

 

S/N

㧦    

FIRM VERSION (MAIN)

 

㧦

CHECK SUM (MAIN)
FIRM VERSION (SUB)
CHECK SUM (SUB)

   

㧦 OK 1234ABCD

OK Ver 0.16 (080101)

㧦
㧦 OK 1234ABCD

㧦 32-61-3C-4E-B6-05
㧦 PC        AV
㧦

㧦

99999H

OK Ver 0.16 (080101)

 

USAGE TIME
MAC ADDRESS
WHITE BALANCE CHECK
CALIBRATION CHECK

  

PC3 PC4 AV3 AV4N 
AV4P AV5N AV5P

SERVICE1

 

SERVICE2

 

SERVICE MENU2                          1/2

 

END

࡮࡮࡮[MENU]

AGING

CALIBRATION

FACTORY RESET

MODEL TYPE

HARDWARE CHECK

WHITE BALANCE SETTING

COMPONENT PHASE

=>

=>

=>

=>

=>

=>

<      JP       >

ʋ

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 29

1)  Enter the “SERVICE MENU 2” mode. 

2)  Select [AGING] with [

2 ] [ 4 ] buttons, and press [3] button.

3)  Select [AGING1] or [AGING2] with [

2 ] [ 4 ] buttons, and press [3]

button. The aging is started. 

AGING1: Every time when [

3] button is pressed, the whole screen

color is changed.

AGING2: The whole screen color is changed every 2 sec.

4)  To terminate aging, turn off the main power source. (The power but-

ton of the remote controller or the machine cannot terminate aging.)

* AGING3 must not be used.

Adjusts the offset and the gain of an A/D converter by the following input mode.

•  PC3 ANALOG mode (D-sub terminal)

•  PC4 ANALOG mode (BNC terminal)

•  AV3 COMPONENT mode (component terminal)

•  AV5 VIDEO mode (composite terminal)

1)  Select the input mode to be adjusted with [INPUT] button. 

2)  The video signal for adjustment is displayed on the screen. 

Note:

•  Be sure to use the following video signal to perform the adjustment. 

•  Since PC2 ANALOG (D-sub terminal) and PC3 ANALOG (BNC terminal) differ in the calibration results, be sure to adjust them with their own

input mode.

•   For AV4 S-VIDEO (S pin), adjust in the input mode of AV5 VIDEO (composite terminal). (The same adjustment value is set.)

Dark
blue

Dark
green

Dark
red

Blue

Green

Red

White

Black

Dark
blue

Dark
green

Dark
red

Blue

Green

Red

White

Black

Input mode

Signal type

Input signal level (Adjusted 

standard value)

signal timing

Input image

PC3 ANALOG

PC  ANALOG  signal
(D-sub terminal)

RGB level: 0.7 Vp-p

1920 

×

 1080 60Hz 

or 
XGA (1024x768) 
60Hz

The adjustment image displayed by executing
“Adj_uty.exe” in the CD-ROM packed together with
the product.
(Or a video image with 0 to 255 gradations of RGB
White)

PC4 ANALOG

PC  ANALOG  signal
(BNC terminal)

PN-S525

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION

2 – 30

3)  Enter the “SERVICE MENU 2” mode. 

4)  Select [CALIBRATION] with [

2 ] [ 4 ] buttons, and press [3] but-

ton. The CALIBRATION screen is displayed.

•  CALIBRATION screen when PC3/PC4 ANALOG mode

•  CALIBRATION screen when AV3 COMPONENT mode

•  CALIBRATION screen when AV5 VIDEO mode

5)  Select [AUTO CALIBRATION] with [

2 ] and [ 4 ] buttons and press

[

3] button. The calibration is executed and the data are saved to

the EEPROM.

The adjustment result is displayed on the ADC OFFSET1/ADC
OFFSET2/ADC GAIN items.

6)  Select [OK] with [

2 ] [ 4 ] buttons, and press [MENU] button. The

CALIBRATION screen is closed.

AV3 COMPONENT

COMPONENT signal Y level: 0.7 Vp-p 

(Pedestal to white level)
Pb/Pr level: 0.7 Vp-p

1080i 60Hz

Full color bar (White 100%, color saturation 100%)

*Recommended signal generator: 

VG-849, VG-859 made by Astro Design.

AV5 VIDEO

VIDEO (NTSC3.58) 
signal 

0.714 Vp-p
(Pedestal to white level)

NTSC3.58

Full color bar (White 100%, color saturation 100%)

*Recommended signal generator: 

VG-849, VG-859 made by Astro Design.

Input mode

Signal type

Input signal level (Adjusted 

standard value)

signal timing

Input image

CALIBRATION    PC3 (ANALOG)

AUTO CALIBRATION

ADC OFFSET1

R : 999

B :

G : 999

999

ADC OFFSET2

R : 999

G :

B :

999

999

ADC GAIN

R : 999

999

999

G :

B :

OK

CANCEL

RESET

CALIBRATION    COMPONENT

AUTO CALIBRATION

ADC OFFSET1

Y : 999

Cr :

Cb : 999

999

ADC OFFSET2

Y : 999

Cb :

Cr :

999

999

ADC GAIN

Y : 999

999

999

Cb :

Cr :

OK

CANCEL

RESET

CALIBRATION    COMPOSITE 

AUTO CALIBRATION (COMPOSIT/S-VIDEO)

ADC OFFSET1

: 999

ADC OFFSET2

: 999

ADC GAIN

: 999

OK

CANCEL

RESET