Sharp LL-S201A (serv.man3) Service Manual ▷ View online
LL-S201A OUTLINE OF THE PRODUCT 1 - 3
1-4. DDC(plug and play)
The monitor supports the VESA DDC(Display Data Channel)standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is
exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect plug-and-play
monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
1-5. SUPPLIED COMPONENTS
- Liquid Crystal Display Monitor:1
- AC adapter:1
- Power cord:1
- Touch pen:1
- Stand(front、back、bottom cover):1
- Fixing screws:2
- USB cable(USB-microUSB Type B):1
- CD-ROM(Utility Disk):1
- Setup Manual:1
※ SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
※ Keep packaging for use when transporting monitor, etc.
1-6. TERMINAL PINS
■HDMI input terminal pins ■Display Port input terminal pins
(HDMITM Connector) (DisplayPort 20 pin)
LL-S201A OUTLINE OF THE PRODUCT 1 - 4
2. PART NAMES
2-1. MONITOR
■Front view
1 Power
LED
Status
Status of the monitor
Green lit
Signal input
Orange lit
No signal input
(Caution)
※ When switching the POWER button off and back on,
always wait for an interval of at least 5 seconds. Rapid
switching may lead to errors or malfunctions.
※ For a complete electrical disconnection, pull out the
main plug.
■Rear view
1 Flap
7 Headphone
jack
2
VESA holes
8
HDMI input terminal
3
Anti-theft hole
9
DisplayPort input terminal
4 Speakers
10
Micro-USB
terminal
5
Power/Menu button
11
AC adapter connection
terminal
6 Cable
clamp
12
Tabs
LL-S201A INSTALLATON / SETTINGS 2 - 1
CHAPTER 2. INSTALLATION / SETTINGS
1. INSTALLATION
1-1. STAND
The monitor can be installed in three different ways.
■Standing position
Place the monitor on the supplied stand.
(Caution) The stand is for use in landscape orientation. It cannot
be used for portrait orientation.
[Assembling the stand]
1) Insert the back into the front.
Align the mark(△)on the front with the edge of the back and
insert the back from above.
2) Slide the back across.
Slide the back until it clicks into place.
3) Attach the bottom cover.
Align the arrow on the bottom cover so that it points toward the
front, and press the projections on the bottom cover into the
pocket on the front and back.
[Mounting the monitor on the stand]
1) Place the stand on a level surface.
2) Set the monitor on the stand.
Set the monitor so that the logo in the center is aligned with the
circle mark on the stand.
※ The stand and the monitor can be secured with fixing screws.
LL-S201A INSTALLATON / SETTINGS 2 - 2
[Disassembling the stand]
1) Remove the bottom cover.
Push the tabs in towards the center and pull.
2) Remove the back from the front.
Depress the button on the front and slide the back across,
then pull the back up.
■Pen writing position
Place the monitor at an angle on a table or other level surface.
1) Hold the flap by the depression on the back of the monitor
and pull the flap up.
2) Place the monitor where you want to use it.
(Caution)
Do not exert a large amount of force on the monitor from above.
Doing so may damage the flap.
■Horizontal position
Place the monitor on a table or other level surface.
(Caution)
When using the monitor horizontally, use the horizontal flap in the
upright position.
1) Lift up the two tabs on the back of the monitor.
2) Place the monitor where you want to use it.
(Caution)
Do not exert a large amount of force on the monitor from above.
Doing so may damage the tabs.
Click on the first or last page to see other LL-S201A (serv.man3) service manuals if exist.