DOWNLOAD Sharp XE-A203 (serv.man7) Service Manual ↓ Size: 1.56 MB | Pages: 93 in PDF or view online for FREE

Part

1

 QUICK START GUIDE

Part

2

Part

3

When not using the take-up spool (using as receipt paper):
• Cut off the excess paper using the edge of the inner cover, and

replace the printer cover.  Press the 

F

key to make sure the

paper end comes out of the printer cover and clean paper
appears.

When using the take-up spool (using as journal paper):
• Insert the end of the paper into the slit in the spool. (Press the 

F

key to feed more paper if required.)

• Wind the paper two or three turns around the spool shaft.
• Set the spool on the bearing, and press the 

F

key to take up

excess slack in the paper.

• Replace the printer cover.

 A203_1 Quick Start Guide  06.5.1 7:25 PM  Page 11

Before starting sales entries, you must first program necessary items so the cash register suits your sales
needs.  In this manual, there are three sections, BASIC FUNCTION PROGRAMMING (pages 12-24) where
required items must be programmed, AUXILIARY FUNCTION PROGRAMMING (pages 46-57) where you
can program for more convenient use of keys on the keyboard, and ADVANCED FUNCTION PROGRAMMING
(pages 58-72) where various optional programming features are provided.  Find the appropriate features for your
needs, and make the necessary programming.

Dept.:

Department; a category for merchandise classifications.  Every sales item should belong to a
department.

PLU:

Price Look Up; a category for merchandise classifications.  PLUs are used to call up preset prices by a
code entry.

VAT:

Value Added Tax

X report: Report to read sales data
Z report: Report to read and reset sales data

Check to see whether a paper roll is present in the machine.  If there is not enough paper on a roll, replace it
with a new one (refer to "Replacing the Paper Roll" on page 82 for the replacement).

Put the manager key in the mode switch and turn it to the PGM position.

Program necessary items into the cash register.
Every time you program an item, the cash register will print the setting.  Please
refer to print samples in each section.

If necessary, issue programming reports for your reference.

0

,

1

to 

9

Numerical key

Used for numerical number entry.

:

Double-zero key

Used for parameter entry and character code entry.

l

Clear key

Used for cancel entry.

P

Point key

Used for decimal point entry and right moving entry (as right cursor key).

@

Multiplication key

Used for left moving entry (as left cursor key).

s

Subtotal key

Used for data decision entry.

A

Finalization key

Used for programming termination entry.

1

2

REG

OPX/Z

MGR

PGM

X1/Z1

X2/Z2

 A203_1 Quick Start Guide  06.5.1 7:25 PM  Page 12

Part

1

 QUICK START GUIDE

Part

2

Part

3

The register allow you to program texts for department item names (page 16), PLU/subdepartment item names
(page 21), function texts (page 56), clerk names (page 23), logo messages (page 23), foreign and domestic
currency symbols (page 55), and training mode texts (page 56).
There are two ways for programming text; using character keys on the keyboard or entering character codes
with numeric keys on the keyboard.  For the latter way, refer to "Entering character codes with numeric keys on
the keyboard" on page 44.

You can enter characters according to the small figures printed in the lower right position of the tops.  For the
layout, please refer to “Keyboard” section on page 6.

The following are used as control keys for character entry:

H

Toggles between upper-case and lower-case letters.  By default, the upper-case letter is selected.  Once
the 

H

key is pressed, you are locked in for entering lower-case letters.  “a” is displayed when lower-

case letters entry is selected as shown in the operator display example below.

N

Press the 

N

key to enter numeric characters.  For example to enter “1”, press the 

N

and 

1

key.

If you press the 

1

key without pressing the 

N

key, the cash register goes to character codes entry

mode.
Once the 

N

key is pressed, you are locked in for entering numeric characters.  "1" is displayed when

numeric characters entry is selected.

W

Toggles between single-size and double-size characters.  By default, the single-size character is
selected.  Once the 

W

key is pressed, you are locked in for entering double size characters.  “W”  is

displayed when double-size characters entry is selected as shown in the operator display example below.

B

Backs up the cursor, erasing the character to the left.

Operator display (Example)

To program the word “Clerk01” with the letter “C” being double size.

To make the letter “C” double size character

To make character size return to normal size

To toggle the characters to lower-case letters

To enter numbers

Wg

W

H

hijk

N01

=C_          W  

=C_             

=C_           a 

=Clerk_       a 

=Clerk01_     a1

ABCD_        Wa1

Cursor

Characters entered using character keys are displayed here.

 A203_1 Quick Start Guide  06.5.1 7:25 PM  Page 13

*Language: 0: English       1: German       2: French       3: Spanish

By default, English is set.

For setting the date, enter the date in 8 digits using the day-month-year (DD/MM/YYYY) format, then press the

s

key.

For setting the time, enter the time in 4 digits using the 24-hour format.  For example, when the time is set to
2:30 AM, enter 230; and when it is set to 2:30 PM, enter 1430.

Time

            1430

           0.00

1430 

s

Time(max. 4 digits in 24-hour format)

s

Date

        22052007

            0.00

22052007

(22 May, 2007)

s

Date(DD/MM/YYYY)

s

LANGUAGE CHANGE 

THANK YOU       

s

88 

@

0 

A

*Language

(0-3)

A

To set  0

s

88

@

3

4

 A203_1 Quick Start Guide  06.5.1 7:25 PM  Page 14