Sharp ER-A160 / ER-A180 User Manual / Operation Manual ▷ View online
39
2.
Make a fold in the paper approx. five centimeters from the end.
3.
While pressing the
á
key, insert the folded end straight into the
paper inlet. The inserted end appears at the printing area.
4
When not using the take-up spool (using as receipt paper):
• Lead the end of the paper out through the manual cutter on the
• Lead the end of the paper out through the manual cutter on the
printer cover. (Press the
á
key to advance the paper more if
required.)
When using the take-up spool (using as journal paper):
• Insert the end of the paper into the slit in the spool.
• Insert the end of the paper into the slit in the spool.
(Press the
á
key to feed more paper if required.)
• Wind the paper two or three turns around the spool shaft.
• If the holding plate is not attached to the spool, attach it by inserting
• If the holding plate is not attached to the spool, attach it by inserting
the spool shaft into the large hole and sliding it into the small one.
• Set the spool on the bearing, and press the
á
key to take up
excess slack in the paper.
5.
Replace the printer cover.
• When using a paper roll as journal paper, you must change
the printer type. Refer to “Programming print format” on
page 30.
page 30.
• When using 2-ply journal/receipt paper, follow the same
instructions as above, but lead the end of the receipt paper
out through the manual cutter after winding the journal
paper on the take-up spool shaft.
out through the manual cutter after winding the journal
paper on the take-up spool shaft.
When printing becomes faded, replace the ink ribbon with a new one specified by SHARP.
Removal
To prevent the ink ribbon form drying or becoming dirty, do not remove it from its bag until just
before using.
before using.
1.
Remove the printer cover.
2.
Cut off the paper and press the
á
key to remove it.
3.
Detach the ink ribbon cover.
Pull the tab in the direction of arrow to lift the cover.
Pull the tab in the direction of arrow to lift the cover.
Replacing the ink ribbon
3
40
4.
Remove the ink ribbon.
Remove the reel that is not locked by the reel stopper first, and tip the
stopper to the opposite side and remove the another reel. To remove
the reels, pull them upwards.
Remove the reel that is not locked by the reel stopper first, and tip the
stopper to the opposite side and remove the another reel. To remove
the reels, pull them upwards.
Installation
The protruding side of reels must face downward. So, note which reel is the left one and which is the right.
1. Install the reel at the side that the reel stopper is not tipped. Rotate
1. Install the reel at the side that the reel stopper is not tipped. Rotate
the reel to the right or to the left until it clicks into place.
2. Run the ink ribbon correctly through the printer as shown on the right
sketch. Note that the ribbon is placed along the outside of the metal
brackets.
brackets.
3. Install the other reel in the same way, and rotate either reel to take up
slack from the ribbon.
4.
Replace the ink ribbon cover.
If the logo becomes too light, it’s time to refill the logo ink. You must use the logo ink specified by SHARP.
Consult your dealer for the logo ink. For refilling the logo ink, follow the procedure given below.
Consult your dealer for the logo ink. For refilling the logo ink, follow the procedure given below.
1.
Remove the printer cover.
2.
Remove the logo by pulling it straight up in the direction of the arrow.
Ink refill (ER-A180 only)
4
41
3.
Pour two or three drops of logo ink through the ink inlet situated on the
back of the logo.
back of the logo.
4.
Replace the logo by the reverse procedure to removing.
5.
Replace the printer cover.
Precautions:
The logo ink first gives a clear print 6 to 10 hours after being applied into the logo. Therefore, refilling at the end
of daily business is most effective. Overinking should be avoided. This will create a blurry print.
Do not apply the logo ink to the ink ribbon.
The logo ink first gives a clear print 6 to 10 hours after being applied into the logo. Therefore, refilling at the end
of daily business is most effective. Overinking should be avoided. This will create a blurry print.
Do not apply the logo ink to the ink ribbon.
Locking the drawer
To lock the drawer, insert the key into the drawer lock and turn it 90 degrees
counterclockwise.
To unlock the drawer, insert the drawer key into the lock and turn it 90 degrees clockwise.
counterclockwise.
To unlock the drawer, insert the drawer key into the lock and turn it 90 degrees clockwise.
Removing the till and the drawer
The till in the register is detachable. After closing your business for the day, remove the till from the drawer and
keep the drawer open. To detach the drawer, pull it forward fully with the till removed, and remove it by lifting it
up.
keep the drawer open. To detach the drawer, pull it forward fully with the till removed, and remove it by lifting it
up.
ER-A160
ER-A180
8-denomination coin case
(detatchable)
Bill case
Till
Drawer
Coin case
Coin case
5-denomination coin case
(detatchable)
Bill case
Bill
separator
Till
Drawer
Coin case
Drawer handling
5
SK1-1
Drawer lock key
42
The drawer automatically opens in the usual way. However, when power failure is encountered or the machine
becomes out of order, slide the lever located on the machine bottom in the direction of the arrow. (See the
figure shown below.) The drawer will not open, if it is locked with a drawer lock key.
becomes out of order, slide the lever located on the machine bottom in the direction of the arrow. (See the
figure shown below.) The drawer will not open, if it is locked with a drawer lock key.
ER-A160
ER-A180
To prevent the register from moving when the drawer opens, use the supplied fixing angle bracket to fix the
drawer to the platform.
drawer to the platform.
How to install the fixing angle bracket
1.
Thoroughly clean the location where the fixing angle bracket (B) is to be placed.
2.
Peel off the adhesive tape on the fixing angle bracket.
3.
Hook the angle bracket onto the hook (A) that is located at the bottom rear of the
register.
register.
4.
Firmly stick the fixing angle bracket to the table surface that your cleaned above.
How to remove the register from the fixing angle bracket
1.
Lift up the front of the register and pull the register towards you.
Installing the fixing angle bracket
7
Lever
Lever
Opening the drawer by hand
6
A
B
Click on the first or last page to see other ER-A160 / ER-A180 service manuals if exist.