DOWNLOAD Sharp BD-HP20H (serv.man2) Service Manual ↓ Size: 8.47 MB | Pages: 56 in PDF or view online for FREE

You can connect audio equipment to the DIGITAL AUDIO OUT terminal or jack.

1 and 2, or 3 and 4).

To COAXIAL 
jack

To OPTICAL 
terminal

or

Optical digital cable 
(commercially available)

Coaxial digital cable 

(commercially available)

To coaxial 
input jack

To optical 
input terminal

3

1

4

2

• Load a disc and start playback. (Pages 25-28)

•  When using COAXIAL/OPTICAL output,
  5.1 ch Digital Output is available.
  7.1 ch Digital Output is not available.

o

You can connect audio equipment or the TV to the 2CH AUDIO output jacks.

1 and 2).

(White)

AV cable (supplied)

1

To 2CH AUDIO 
output jacks

(Red)

(White) (Red)

• Load a disc and start playback. (Pages 25-28)

2

To audio 
input jacks

p

Press down on the tab in the direction of the 
arrow to remove the battery cover.

Load the two R-03 size batteries (“AAA” size, 
UM/SUM-4) supplied with the remote control 
unit. Make sure that the battery poles 

m and n 

are positioned as indicated.

Slide the battery cover in the direction of the 
arrow until it clicks.

•  Do not subject the remote control unit to shock, water or 

excessive humidity.

•  The remote control unit may not function if the Player's remote 

sensor is in direct sunlight or any other strong light.

•  Incorrect use of batteries may cause them to leak or burst. Read 

the battery warnings and use the batteries properly.

•  Do not mix old and new batteries, or mix different brands.
•  Remove the batteries if you will not use the remote control unit for 

an extended period of time.

Remote control sensor

Remote control unit

30º

30º

7 m

Plug the supplied AC cord into the AC IN terminal on the rear 
of the Player. Then plug into AC outlet.

•  Place the Player close to the AC outlet, and keep the power plug 

within reach.

•  TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH THE 

UN-INSULATED PARTS OF ANY CABLES WHILE THE AC CORD 
IS CONNECTED.

• The 

a (STANDBY) indicator blinks while the Player is preparing for 

starting up. You cannot turn the Player on until the 

a (STANDBY) 

indicator stops blinking.

To AC IN terminal

To AC outlet

•  3 types of remote control codes operate this Player: 

RC-1, RC-2 and RC-3. If you operate this Player 
by remote control along with another SHARP 
Blu-ray Disc Player or DVD Player placed next to it 
simultaneously, switching the remote control code 
(both the Player and remote control) to one of the 
signals (RC-1, RC-2 or RC-3) will let you operate 
only with this Player.

•  Make sure to set the Player and remote control to 

the same remote code. You can not operate the 
Player if they are not set to the same code.

 Setting the code to “RC-3”.

Press and hold 3 fi rst and then 

B 

on the remote control together for 
more than 5 seconds.

Press 

B to turn off the player.

Point the remote control at the 
player, then press and hold the 
DISPLAY button.

• TV Power: 

B

•  TV Channel up/down: P 

r / s

•  TV Volume up/down: 

i 

e/f

• TV-AV Selector: 

b

The Universal Remote Control may operate the 
basic functions of the TV of SHARP.

Approx. 2 sec. later

Approx. 3 sec. later

B

 (POWER)

Firstly, press 

B to turn on this player.

Press 

B on the remote control and check the 

front panel display (RC-1, RC-2 or RC-3).
Set the remote control code according to the 
display and press 

B to see if you can turn 

on/off the Player.

 Change “RC-1” to “RC-3”.

Remote control sensor

 

The display on the player changes 
as shown below, and the player will 
be set to the same number as the 
remote control.