Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) Service Manual ▷ View online
DIS-19
SECTION 2 DISASSEMBLY PROCEDURES
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
Relay lens(IN)
Relay lens(IN)
Relay lens(OUT)*
Dichroic mirror (G)
Dichroic mirror B
Mirror (R)
Mirror (B)*
Condenser lens (G/B)
Mirror (R)
Coated side comes
reflection side
Coated side comes
reflection side
Marking comes this
side up
Marking comes this
side up
3.8. Parts location and direction in the lighting case
When mounting or assembling the parts in the lighting case, the parts must be mounted in the speci-
fied location and direction as shown in the figure below.
Note: The parts indicated with (*) are mounted by adhesive, therefore, they cannot be replaced
individually.
Condenser lens (G/B)
DIS-20
SECTION 2 DISASSEMBLY PROCEDURES
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
<Cable reforming>
Reform the cables as shown in the figure below. Place the cables at the original
position after replacing the parts.
Ferrite core
K8L
K9A
K8D
K9D
K8H
K8I
K9G
K8000
K9C
K9E
K8E
K8G
K9F
K8R
Connector
Connect to
K8L
Intake temp. sensor [M1]-P.C.B
K9A
Intake fan1
K8D
RC [R]-P.C.B
K9D
Intake fan4
K8H
Lamp ballast [B]-P.C.B
K8I
Lamp connect [C]-P.C.B
Connector
Connect to
K9G
Power fan
K8R (Behind)
Power [P]-P.C.B
K8000
Iris unit
K9C
Intake fan3
K9E (Behind)
Lamp fan
K9F
Exhaust fan
K8E (Behind)
Exhaust temp. sensor [M3]-P.C.B
K8G (Behind)
Filter temp. sensor [M2]-P.C.B
SECTION
3
ADJ-1
(2017-06)
SECTION 3 ADJUSTMENTS
CONTENTS
1. Adjustment Items and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . ADJ-2
1. 1. Lighting area adjustment
1. 2. Polarizer adjustment
1. 3. Adjusted data transfer
1. 4. Panel type setting
1. 5. Flicker adjustment
1. 6. White balance adjustment
1. 7. Model no. setting
1. 8. Clogging sensor calibration
1. 9. Keystone calibration
1. 10. Electrical convergence adjustment ( for PT-VZ585N/VZ580)
1. 11. Ghost feedback calibration ( for PT-VZ585N/VZ580)
1. 2. Polarizer adjustment
1. 3. Adjusted data transfer
1. 4. Panel type setting
1. 5. Flicker adjustment
1. 6. White balance adjustment
1. 7. Model no. setting
1. 8. Clogging sensor calibration
1. 9. Keystone calibration
1. 10. Electrical convergence adjustment ( for PT-VZ585N/VZ580)
1. 11. Ghost feedback calibration ( for PT-VZ585N/VZ580)
2. Firmware Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADJ-12
ADJ-2
SECTION 3 ADJUSTMENTS
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
1. 1. Lighting area adjustment
1. 1. 1. Lighting area confirmation
1. After replacing the condenser lens, check if any shade is visible in the panel display area,
* Make the projection environment as dark as possible, and project the all-white pattern (internal pattern) for this check.
2. If there is vignetting on the screen, adjust the Condenser lens-out position.
Lighting area
Effective area
1. Adjustment Items and Procedures
When the following parts are disassembled or replaced, please adjust the items according to the table below.
Need to adjust
m
Need to check
Adjustment Item
Replaced Component
Remarks
Con-
denser
lens
Optical
block
Polarizer
[A]-P.C.B
1.1. Lighting area adjustment
m
Adjust if there are color unevenness on the screen
1.2. Polarizer adjustment
Adjust if there are the color shading on the screen
1.3. Adjusted data transfer
Transfer the data from old [A]-P.C.Board to new
one
1.4. Panel type setting
m
Not necessary if "1.3. Adjusted data transfer" is
taken
1.5. Flicker adjustment
1.6. White balance adjustment
m
m
1.7. Model no. setting
Not necessary if "1.3. Adjusted data transfer" is
taken
1.8. Clogging sensor calibration
Not necessary if "1.3. Adjusted data transfer" is
taken
1.9. Keystone adjustment
1.10 Electric convergence
adjustment
(for VZ585N/VZ580)
m
Not necessary if "1.3. Adjusted data transfer" is
taken
1.11 Panel ghost feedback
calibration
(for VZ585N/VZ580)
*1
*1 Item "1.3. Adjusted data transfer" should be
taken if the A-P.C.board is replaced.
Click on the first or last page to see other PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) service manuals if exist.