DOWNLOAD Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) Service Manual ↓ Size: 21.33 MB | Pages: 100 in PDF or view online for FREE

PT-VZ585N

PT-VW545N

PT-VX615N

PT-VZ580

PT-VW540

PT-VX610

ORDER NO. VED1706655CE

(2017-06)

For the block diagrams, schematic diagrams and parts list, refer to each separated booklet "Block and Schematic 

diagrams" and "Parts List" respectively.



 This manual is common to the models regardless of suffixes of the Model No. 

  The suffix of model no. shows the destination as the below.
  - "T" for Taiwan
  - "D" for India
  The model which does not have the destination suffix is for global model in common.



 Illustrations in this service manual

  Illustrations of the projector, screen, and other parts may vary from the actual product.
 

Illustrations of the projector with the power cord attached are only examples.

   The shape of the supplied power cords varies depending on the country where you purchased the product.

2

 

  

Never use this projector at an altitude of 2 700m or higher.

    Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.

  

This projector is using the P.C.Board which applies lead free solder.

    Use lead free solder in servicing from the standpoint of antipollution for the global environment.

 

  

•  Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder 

Typically the melting point is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature 

limitation function and set it to 370 ± 10 °C.

    •  Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 

600°C or higher).

    •  Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably 

use lead solder, use lead solder after removing lead free solder. Or be sure to heat the lead free solder until it melts 

completely, before applying lead solder.)

    •  After solder to double layered P.C Boards, check the component side for excess solder which may flow onto the oppo-

site side.

    About the identification of the lead free solder P.C.Board.

     For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the 

surface or the back of P.C.Board.

PbF

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC 

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated 

in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to 

correct the interference at his own expense.

Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

There are special components used in this equipment which are important for safety. These parts are marked by 7 in the 

schematic diagram, circuit board diagrams, exploded views and replacement parts list. It is essential that these critical parts 

should be replaced with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original 

design without permission of manufacturer.

The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.

Le technicien d'entretien doit lire et suivre les «Précautions de sécurité» et «Avis important de sécurité» dans ce manuel d'entretien.

7

This service information is designed for experienced repair technicians only and is not designed for use by the general pub-

lic. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service 

a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any 

attempt to service or repair the product or products dealt with in this service information by anyone else could result in seri-

ous injury or death.

7

 

Ce document d'entretien est destiné aux techniciens d'entretien expérimentés uniquement et n'est pas conçu pour une 

utilisation par le grand public. Il ne contient pas des avertissements ou des mises en garde pour aviser les non-techniciens 

des dangers potentiels lorsqu'ils tentent de réparer un produit. Les appareils alimentés par l'électricité doivent être révisés 

ou réparés uniquement par des techniciens professionnels expérimentés. Toute tentative d'entretenir ou de réparer le ou les 

produits traités dans ce document d'entretien par autrui peut entraîner des blessures graves ou la mort.

 

  Risk of explosion if battery is replaced by an incorrect type.

    Replace only with the same of equivalent type recommended by the manufacturer.

    Dispose of used batteries according to the manufacturer’s instructions.

    Risque d'explosion si la batterie est remplacée par un type incorrect.

    Remplacez-la uniquement par le même type ou le type équivalent recommandé par le fabricant.

    Jetez les batteries usagées conformément aux instructions du fabricant.

3

 

f

In case of fuse opening inside the projector, Do not turn the projector on just replacing the fuse with new one be-

cause there might be a possibility to have smoking or firing hazard. Turn it on after solving the main cause of fuse 

opening.

 

f

After repairing, confirm that the projector operates correctly.

 

f

Pay attention to handle the projector as customer's personal settings have been remaining inside the projector.  

 

f

When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.  

Doing so may damage the internal parts and result in malfunctions.

 

f

Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

r

The projector is designed for indoor use only. 

r

 

f

Places where vibration and impacts occur such as in a car or vehicle: Doing so may damage the internal parts 

and result in malfunctions.

 

f

Location close to sea or where corrosive gas may occur: the projector may fall due to corrosion. Also, failure to do 

so may shorten the life of the components and result in malfunction.

 

f

Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare 

cases due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the 

projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.

 

f

Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of the 

luminous lamp, or result in deformation of the outer case due to heat, which may cause malfunction. Make sure to 

observe the operating temperature range of the projector.

 

f

Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.

r

This requires an optional ceiling mount bracket. Be sure to use the Projector Mount Bracket together with the ceiling 

mount bracket for high ceilings or low ceilings.

r

Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate

installation.

r

If there is any facility or equipment which outputs strong radio waves near the installation location, install the projec-

tor at a location sufficiently far from the source of the radio waves. Or, wrap the LAN cable connected to the <DIGI-

TAL LINK/LAN> terminal using a piece of metal foil or a metal pipe which is grounded at both ends.

r

The projection lens is thermally affected by the light from the light source, making the focus unstable in the period 

just after switching on the power. It is recommended that the images are projected continuously for at least 30 min-

utes before the focus is adjusted.

r

r

Using the projector in a location that the altitude is too high or the ambient temperature is too high may shorten the 

life of the components or result in malfunctions.

The upper limit of the operating temperature of the projector varies depending on the altitudes of the operating envi-

ronment. 

4

When using it at altitudes below 1 200 m (3 937') above sea level: 0 °C (32 °F) ~ 40 °C (104 °F)  

When using it at altitudes between 1 200 m (3 937') and 2 700 m (8 858') above sea level: 0 °C (32 °F) ~ 30 °C 

(86 °F).

r

Do not tilt the projector body more than approximately ±30 degrees longitudinally or ±15 degrees laterally. Over 

tilting may result in shortening the life of the components. 

Within 15°

Within 15°

Within 30°

Within 30°

 

f

Use the adjustable feet only for the  oor standing installation and for adjusting the angle. Using them for other 

purposes may damage the projector.

 

f

Do not stack the projectors.

 

f

Do not use the projector supported by its top.

 

f

Do not block the ventilation ports (intake and exhaust) of the projector.

20 - ENGLISH