Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) Service Manual ▷ View online
INF-19
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
1. FREEZE MESSAGE
• Setting the display of on-screen message "FREEZE"( ON/OFF). initial value: ON
- ON : Display "FREEZE" message in the freeze mode.
- OFF : Not display "FREEZE" message in the freeze mode.
- Switch the ON/OFF with buttons.
2. FAN FULL MODE
• Setting the mode of cooling fan motor to the maximum. initial value: OFF
- ON : Fixed high speed cooling mode.
- OFF : Normal mode (Spinning speed changes depending on the surrounding temperature)
- Switch the ON/OFF with buttons.
3. 640x480/60/480/60p
• Setting the switching mode of RGB input signal. initial value: AUTO
- AUTO : Select 640x480/60 or 480/60p of RGB input signal automatically.
- 640x480/60 : Select 640x480/60 mode forcedly.
- 480/60p : Select 480/60p mode forcedly.
- Switch the RGB input signal with buttons.
4. EMULATE
• Setting the serial command format when using other model's serial control commands. initial value: DEFAULT
-DEFAULT: Standard
-D3500
-D4000
-D/W5k series
-D/W/Z6k series
-L730 series
-L780 series
-L735 series
-L785 series
-F/W series
-LZ370
-LB/W series
-VX500 series
-EZ570 series
-VW431D
-MODE_HI: other company
-MODE_NE: other company
-MODE_EP: other company
-MODE_SA: other company
-MODE_SH: other company
-MODE_MI: other company
-MODE_SO: other company
-MODE_IN: other company
-OTHER:other models
- Switch the emulate with buttons.
5. BAUD RATE
• Setting the baud rate of RS232C communication. Initial value:9600
- 9600 / -19200 / -38400 / - 57600 / -115200
* The using baud rate will be set when the OTHER is selected in the EMULATE menu. (Use 9600 in normal)
- Switch the baud rate with buttons.
6. VERSION
* The version no. of command will be displayed when the MODE_** (other company) or OTHER is selected in the EMULATE
menu.
7. INPUT SELECT
* The input select command will be assigned when the MODE_IN is selected in the EMULATE menu.
INF-20
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
(1) – Model No.
(2) – Software version of each microprocessor
MM: Main microprocessor, SM: Sub microprocessor,
NT: Network microprocessor,
BALLAST: Ballast microprocessor
DIGITAL LINK: DIGITAL LINK microprocessor
(3) – Version no. of EMULATE software(When selecting other com-
pany)
[DEFAULT] means not set.
(4) – Input signal name, [NO SIGNAL] means no signal
Input signal frequency (Horizontal / Vertical)
(5) – Projector serial no.
(6) – Status of correction data in the memories
G-SAVED: Gamma correction data
U-SAVED: Color shading correction data
Display is [NG], if no data
---------------------- TEMP ----------------------------------------------
(7) – Temperature error Check
(8) – Measured value of temperature sensors (Celsius)
INTK (Intake air) / EXST (Exhaust air) / FLTR (Filter clogged)
GLOG ( Detected value of clogged sensor)
(9) – Measured value of temperature sensors (Celsius) when the
latest shutdown occurred by temp error.
INTK (Intake air) / EXST (Exhaust air) / CLOG (Filter clogged)
FLTR C.V. (Correction value of filter clogged)
---------------------- FAN ------------------------------------------------
(10) – Fan rotation check
INTK1 / INTK2 / INTK3 / LAMP / POWER / EXST
---------------------- MECHANICAL -----------------------------------
(11) – Iris error check (NG: error)
---------------------- LAMP ----------------------------------------------
(12) – lamp error check
(13) – Lamp memory communication check (NG: error)
(14) – Judge the
lamp usage time
( Normal converted value)
---------------------- UNIT HISTORY ----------------------------------
(15) – Projector accumulated runtime
(16) – Lamp runtime reset times
(17) – Lamp on time
First line --- Current ( Actual time lamp on times
Normal converted value)
Second line--- 1 time before reset (Actual time lamp on
times Normal converted value)
Third line --- 2 times before reset (Actual time lamp on
times Normal converted value)
8. SELF CHECK
• Displays the self diagnostic information
9. TEST PATTERN
• Displays test patterns of White/Red/Green/Blue raster signals.
- Change the patterns by
▲▼
buttons,
Change the color by buttons.
10. FLICKER ADJUST
• Perform the flicker adjustment. ( Refer to "SECTION 3 Adjustment")
11. MODEL NO. SETTING
• Setting up the model no. of the projector. ( Refer to "SECTION 3 Adjustment")
12. PANEL TYPE SETTING
• Setting up the LCD panel type (L-Type or R-Type). ( Refer to "SECTION 3 Adjustment")
13. WHITE BALANCE ADJUST
• Adjust the white balance. ( Refer to "SECTION 3 Adjustment")
14. KEYSTONE CALIBRATION
• Perform the auto keystone calibration. ( Refer to "SECTION 3 Adjustment")
6(/)&+(&.
02'(/379=
02'(/379=
61'%
00
60
17
%$//$67
',*,7$//,1.F
(08/$7(6
;*$
+.+=
(08/$7(6
;*$
+.+=
*6$9('
2.
9+=
86$9('
2.
7(03
7(03
7(03
2.
,17.
,17.
(;67
(;67
)/75
)/75&9
&/2*
&/2*
)$1
,17.,17.,17./$03(;6732:(52.
0(&+$1,&$/
,5,6
,17.,17.,17./$03(;6732:(52.
0(&+$1,&$/
,5,6
2.
/$03
/$03
/$03
2.
+
2.
0(025<
2.
81,7+,6725<
727$/
727$/
+
5(6(7
+
+
+
+
+
+
①
②
④
⑦
⑧
⑩
⑪
⑫
⑬
⑮
⑰
⑤
③
⑥
⑨
⑭
⑯
* The display information varies depending on the input signal and
version of the software.
* The word "OK" of Items (TEMP/FAN/MECHANICAL/LAMP)
would be indicated in red if the projector had shutdown due to
abnormality last time.
INF-21
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
15. CLOG SENSOR CALIBRATION
• This is to calibration the clog sensor circuit. This calibration is necessary when the [A]-P.C. board , EEPROM or clogging
sensor is replaced. ( Refer to "SECTION 3 Adjustment")
16. CLOG SHUTDOWN
• Setting up the shutdown specification by the clogging sensor. initial value: ON
The specification will change as the below when the function is "OFF".
1) Disable the function "Transition to Lamp ECO mode" and "Shutdown" due to the rising of value of filter clogging sensor.
2) Sets up the filter counter timer to [1000H].
3) Disable the function of OSD warning message when the filter counter timer reaches the setting value.
When setting to "ON", the filter counter timer is set to default and enable the functions on items 1)
to 3).
- Witches the function On / Off with button.
17. VALENS
• Displays information about Valens. Displays information with [ENTER] button.
18. DIGITAL LINKS SETUP (Only for PT-VZ585N,PT-VW545N,PT-VX615N)
• Setting up the communication mode of DIGITAL LINK and the Ethernet. initial value: AUTONEGOTIATION
DIGITAL LINK SETUP
DUPLEX(ETHERNET)
AUTONEGOTIATION
DUPLEX(DIGITAL LINK)
AUTONEGOTIATION
STORE
Available mode
Description
AUTONEGOTIATION
The communication method is set automatically.
100BaseTX-FUll
Full-duplex communication method is set.
100BaseTX-Half
Half-duplex communication method is set.
- Select the item with
▲▼
button, change the mode with button.
After setting, select the [ STORE] and press the [ENTER] button to save the setting.
19. RGB PIXEL ADJUST (Only for PT-VZ585N/PT-VZ580)
• Adjust the convergence. Each pixel cab be moved +- 2 dots vertically and horizontally.( Refer to "SECTION 3 Adjustment")
20. GHOST FB CALIBRATION (Only for PT-VZ585N/PT-VZ580)
• Perform the panel ghost feedback calibration.( Refer to "SECTION 3 Adjustment")
21. HDMI EQUALIZER
• Setting up the equalizer of HDMI input signal (AUTO, LOW, MID, HIGH). initial value: AUTO
- Switch the equalizer level with button.
22. SIGNAL SENSITIVITY
• Setting up the delay time of no signal by HDMI1/2 signal . (0 ~ 15) initial value: 0
- Change the delay time with buttons.
23. CLAMP POSITION
• Adjust the clamp position. (1~255) initial value:1
- Setting up clamp position with buttons.
The function is enabled when select the COMPUTER1/2 .
24. THRESHOLD SW
• Switch the threshold of Synchronization signal. ( LOW, HIGH) initial value: LOW
- Select the item with
▲▼
button, setting up the slice level with buttons.
25. WAIT UNMUTE
• Setting up the mute time at the start of audio output.(0ms, 250ms, 500ms, 750ms, 1.0s, 1.5s, 2.0s)). initial value:250ms
- Switch the delay time with buttons.
It is enabled when input signal HDMI1/HDMI2/DIGITAL LINK/Network.
INF-22
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
4. Notes on service
4. 1. Before service operation
4. 1. 1. LCD panel
1. The display unit of this projector comprises three LCD panels. Although an LCD panel is a product of high-precision tech-
nology, some of the pixels on the image may be missing or constantly lit. Please note that this is not a failure.
2. Displaying a still image for a longer time may result in an after-image on the LCD panels. If this happens, display the all
white screen in the test pattern for an hour or more.
4. 1. 2. Lamp
1. The light source of the projector is a high-pressure mercury lamp.
2. A high-pressure mercury lamp has the following characteristics.
• The luminance of the lamp will decrease by duration of usage.
• The lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or degradation due to
cumulative runtime.
• The lamp life varies greatly depending on individual differences and usage conditions. In particular, continuous use for 12
hours or more and frequent off/on switching of the power greatly deteriorate the lamp and affects the lamp life.
• In rare cases, the lamps burst shortly after projection starts.
• The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the lamp unit
regularly.
(Refer to items “When to replace the lamp unit”, “How to replace the lamp unit”)
• If the lamp bursts, gas contained inside of the lamp is released in the form of smoke.
• It is recommended that you store the Replacement Lamp Unit as a contingency
Replacement lamp unit : ET-LAV400
Note
* Panasonic takes no responsibility for any damage or malfunction of the
product resulting from use of lamp units which are not manufactured by
Panasonic. Use only specified lamp units.
Attention * Please be sure to read the warnings and notices on the lamp that is
described in the Operating Instructions. "Read this first!", "Precautions for
use", "Maintenance/replacement"
4. 1. 3. Air filter unit
1. Make sure that the air filter unit is properly attached before using the projector. If it is
not properly attached, the projector will suck in dirt and dust causing a malfunction.
2. The cleaning and replacement cycle of the air filter unit varies depending on the usage
environment.
Replacement air filter unit : ET-RFV410
Click on the first or last page to see other PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) service manuals if exist.