Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) Service Manual ▷ View online
INF-3
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
Attention
f
Do not drop the remote control.
f
Avoid contact with liquids.
f
Do not attempt to modify or disassemble the remote control.
f
Please observe the following contents that are described on the back of the remote control unit (see the picture below).
g
Do not use a new battery together with an old battery.
g
Do not use unspecified batteries.
g
Make sure the polarities (+ and -) are correct when inserting the batteries.
In addition, please read the contents that are related to batteries in the "Read this first!".
1. 请勿把旧电池和新电池一起使用。
2. 请勿使用不合规格的电池。
3. 确保电池安装正确。
原产地:中国
1.Do not use old battery with new one.
2.Do not use batteries other than the
2.Do not use batteries other than the
type specified.
3.Be sure the batteries are inserted properly.
3.Be sure the batteries are inserted properly.
Made in China
Caution label at the back of the remote control
Note
f
The remote control can be used within a distance of about 7 m (22′11-5/8″) if pointed directly at the remote control signal receiver. The
remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate correctly.
f
You can operate the projector by reflecting the remote control signal on the screen. The operating range may differ due to the loss of light
caused by the properties of the screen.
f
When the remote control signal receiver is lit with a fluorescent light or other strong light source, the projector may become inoperative. Set
the projector as far from the luminous source as possible.
Projector body
4
5
12
13
4
1
2
3
10 11
8 9
6
6
6
7
6
r
Front
r
Side
r
Rear
: Projection direction
WARNING
Keep your hands and other objects away from the air exhaust
port.
f
Keep your hands and face away.
f
Do not insert your fingers.
f
Keep heat-sensitive objects away.
Heated air from the air exhaust port can cause burns, injury, or
deformations.
1 Remote control signal receiver
2 Focus Lever
2 Focus Lever
Adjusts the focus.
3 Zoom Lever
Adjusts the zoom.
4 Adjustable feet
Adjusts the projection angle.
5 Projection Lens
6 Air exhaust port
7 Speaker
8 <AC IN> terminal
6 Air exhaust port
7 Speaker
8 <AC IN> terminal
Connects the supplied power cord.
9 Security slot
This security slot is compatible with the Kensington security
cables.
10 Burglar hook port
Attaches a burglar prevention cable, etc.
28 - ENGLISH
Chapter 1 Preparation - About your projector
1. 2. Projector body (for PT-VZ585N,PT-VW545N,PT-VX615N)
INF-4
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
11 Connecting terminals (
page 30)
12
13 Air intake port
2
3
1
5
4
r
Top
r
Bottom
:
Projection direction
1 Vertical lens shift dial
Adjusts the projecting position in the vertical direction (vertical
shift).
2 Control panel and Indicators
3 Lamp cover
The luminous lamp is inside.
4 Air exhaust port
5 Burglar hook port
5 Burglar hook port
Attaches a burglar prevention cable, etc.
Attention
f
Do not block the ventilation ports (intake and exhaust) of the projector.
r
Control panel and Indicators
8
9
10
1
2
3
4
3
4
6
5
7
1 Power button <v/b> (v Standby / b Power on)
Sets the projector to the state where the projector is switched
off (standby mode). Also starts projection when the power is
switched off (standby mode).
2 Power indicator <ON(G)/STANDBY(R)>
Displays the status of the power.
3 Lamp indicator <LAMP>
Displays the status of the luminous lamp.
4 Temperature indicator <TEMP>
Displays the status of the internal temperature.
5 Ambient luminance sensor
6 <MENU> button
6 <MENU> button
Displays or hides the main menu.
When the sub menu is displayed, pressing it will return to the
previous screen.
7 <ENTER> button
Determines and executes an item in the menu screen.
8 <INPUT SELECT> button
Switches the input signal to project.
9 asqw buttons
Used to select the menu screen items, switch the setting or
adjust the level.
Also used to enter a password in the [SECURITY] menu or enter
characters
10 <AUTO SETUP/CANCEL> button
Used to
automatically adjust with auto setup function while
projecting the image . It is also used to operate
the Memory Viewer screen and the idle screen of MIRRORING
input and Panasonic APPLICATION input.
ENGLISH - 29
Chapter 1 Preparation - About your projector
INF-5
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
1. 3. Connecting terminals (for PT-VZ585N,PT-VW545N,PT-VX615N)
r
Connecting terminals
1 2
3
4
5
6
7
8
9
10
11
1 <COMPUTER 2 IN/1 OUT> terminal
This is the terminal to input RGB signals or YC
B
C
R
/YP
B
P
R
signals.
It can also output the signals input from <COMPUTER 1 IN>
terminal to an external device.
2 <COMPUTER 1 IN> terminal
This is the terminal to input RGB signals or YC
B
C
R
/YP
B
P
R
signals.
3 <HDMI 1 IN> terminal / <HDMI 2 IN> terminal
These are the terminals to input HDMI signal.
4 <USB B (DISPLAY)> terminal
This terminal is used to connect the projector to the computer
with a USB cable when you want to use the USB display function
of the application software "Wireless Manager ME6.4".
For details, refer to the "Operating Instructions-Wireless Manager
ME6.4" in the CD-ROM.
5 <USB A (VIEWER)> terminal
This is the terminal to attach the USB memory when using the
Memory Viewer function or the Pairing function.
6 <DIGITAL LINK/LAN> terminal
This is a terminal to connect a device that transfer video
signal or audio signal via the LAN terminal. Also, this is the LAN
terminal to connect to the network.
7 <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control the
projector by connecting a computer.
8 <VIDEO IN> terminal
This is the terminal to input video signals.
9 <AUDIO IN 3> terminal
This is the terminal to input audio signals.
Left input <L> and right input <R> are provided for the <AUDIO
IN 3> terminal.
10 <AUDIO IN 1> terminal / <AUDIO IN 2> terminal
These are the terminals to input audio signals.
11 <VARIABLE AUDIO OUT> terminal
This is the terminal to output the input audio signal.
Attention
f
When a LAN cable is directly connected to the projector, the network connection must be made indoors.
30 - ENGLISH
Chapter 1 Preparation - About your projector
INF-6
SECTION 1 SERVICE INFORMATION
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
Attention
f
Do not drop the remote control.
f
Avoid contact with liquids.
f
Do not attempt to modify or disassemble the remote control.
f
Please observe the following contents that are described on the back of the remote control unit (see the picture below).
g
Do not use a new battery together with an old battery.
g
g
Make sure the polarities (+ and -) are correct when inserting the batteries.
1. 请勿把旧电池和新电池一起使用。
2. 请勿使用不合规格的电池。
3. 确保电池安装正确。
原产地:中国
1.Do not use old battery with new one.
2.Do not use batteries other than the
2.Do not use batteries other than the
type specified.
3.Be sure the batteries are inserted properly.
3.Be sure the batteries are inserted properly.
Made in China
Caution label at the back of the remote control
Note
f
The remote control can be used within a distance of about 7 m (22′11-5/8″) if pointed directly at the remote control signal receiver. The
remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate correctly.
f
caused by the properties of the screen.
f
the projector as far from the luminous source as possible.
Projector body
4
5
12
13
4
1
2
3
10 11
8 9
6
6
6
7
6
Front
Side
Rear
Projection direction
WARNING
Keep your hands and other objects away from the air exhaust
port.
f
Keep your hands and face away.
f
f
Keep heat-sensitive objects away.
Heated air from the air exhaust port can cause burns, injury, or
deformations.
1 Remote control signal receiver
2 Focus Lever
2 Focus Lever
Adjusts the focus.
3 Zoom Lever
Adjusts the zoom.
4 Adjustable feet
Adjusts the projection angle.
5 Projection Lens
6 Air exhaust port
7 Speaker
8 <AC IN> terminal
6 Air exhaust port
7 Speaker
8 <AC IN> terminal
Connects the supplied power cord.
9 Security slot
This security slot is compatible with the Kensington security
cables.
10 Burglar hook port
Attaches a burglar prevention cable, etc.
11 Connecting terminals
12
12
13 Air intake port
ENGLISH - 23
Chapter 1 Preparation - About your projector
OM_VZ580_EN.indd 23
2017/5/9 10:20:20
1. 4. Remote controls (for PT-VZ580,PT-VW540,PT-VX610)
About your projector
Remote control
2
1
3
7
5
8
6
9
10
11
11
4
13
12
14
15
16
15
16
17
Front
1 Remote control signal transmitter
2 Power <v/b> button (v standby / b power on)
2 Power <v/b> button (v standby / b power on)
Sets the projector to the state where the projector is switched
off (standby mode). Also starts projection when the power is
switched off (standby mode).
3 Input selection buttons (<COMPUTER 1> / <COMPUTER 2> /
<VIDEO> / <HDMI 1> / <HDMI 2>)
Switches the input signal to project.
4 <MENU> button / <RETURN> button / asqw buttons /
<ENTER> button
Used to operate the menu screen.
The asqw buttons are also used to enter password or
characters for [SECURITY].
5 <FREEZE> button
Pauses the projected image and mute the audio temporarily.
6 Number (<1> - <6>) buttons
Used for entering an ID number in a multiple projector
environment or a password.
7 <AUTO SETUP> button
Used to
perform automatic adjustment while projecting the
image.
8 <MUTE> button
Used to temporarily mute the projector.
9 <AV MUTE> button
Used to turn off the audio and video temporarily.
10 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
11 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
12 <D.ZOOM +> button / <D.ZOOM -> button
Zooms in and out the images.
13 <VOL +> button / <VOL -> button
Adjusts the volume level of the built-in speaker or the audio
output.
14 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment.
15 <ID ALL> button
Used to simultaneously control all the projectors with one
remote control when using multiple projectors.
16 <P-TIMER> button
Operates the presentation timer function.
17 <SCREEN ADJ> button
Corrects the distortion of the projected image.
22 - ENGLISH
Chapter 1 Preparation - About your projector
OM_VZ580_EN.indd 22
2017/5/9 10:20:17
Click on the first or last page to see other PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man3) service manuals if exist.